Weslo Cadence 80 Treadmill User Manual - Page 7

Upright Spacer and the Frame. Remove the 3 1/2 Bolt.

Page 7 highlights

3. Open part bag B. Hold an Upright Spacer (59) against 3 one side of the Frame (96) as shown. Insert a 3 1/2" Bolt (54) into the indicated hole in the Upright Spacer and the Frame. Next, tighten a 3/4" Tek Screw (9) into the Upright Spacer and the Frame. Remove the 3 1/2" Bolt. Repeat on the other side of the Frame. Have a second person lift the front end of the Frame (96). Insert a 3 1/2" Bolt (54) with a 3/8" Star Washer (55) into the Right Upright (104) and the right Upright Spacer (59), and tighten the Bolt into the Frame. Do not overtighten the Bolt. Repeat on the left side of the Frame. 96 9 59 104 55 54 Hole 4. Attach the Latch Housing (46) to the Left Upright (47) with two 3/4" Screws (38). Make sure that the large hole in the Latch Housing is on the side shown. Remove the Latch Knob (48) from the Latch Pin (52). Make sure that the Latch Pin Collar (49) and the Spring (50) are on the Latch Pin. Insert the Latch Pin into the Storage Latch (46), and then tighten the Latch Knob back onto the Latch Pin. 4 48 38 46 47 Large Hole 50 49 52 5. Identify the Right Handrail (41), which has a large hole in the left side. Feed the Wire Harness (65) up into the bracket on the Right Handrail and out of the large hole in the left side. (Note: It may be helpful to use needlenose pliers to pull the Wire Harness out of the hole.) Remove any plastic ties from the bracket. Insert the bracket on the Right Handrail (41) into the upper end of the Right Upright (104). Attach the Right Handrail with two 1" Bolts (43), two 1/4" Washers (44), two 1/4" Star Washers (45), a 4" Bolt (117), and a 5/16" Washer (122) as shown. Do not tighten the Bolts yet. See drawing 5a. Insert the included nylon tie through the indicated hole in the Right Handrail (41). See drawing 5b. Look into the Right Handrail (41) and make sure that the Wire Harness (65) is secured to the side shown. Tighten the nylon tie and cut the excess off the end. Attach the Left Handrail (not shown) in the same way. Note: You may need to tip the Left Handrail to one side as you insert the bracket into the top of the Left Upright. There is not a wire harness in the Left Upright. 7 5 65 Large Hole Bracket 41 43 44 45 43 44 45 104 117 122 5a Tie 5b Tie 41 41 65

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23

7
5. Identify the Right Handrail (41), which has a large hole in
the left side. Feed the Wire Harness (65) up into the
bracket on the Right Handrail and out of the large hole in
the left side. (Note: It may be helpful to use needlenose
pliers to pull the Wire Harness out of the hole.) Remove
any plastic ties from the bracket.
Insert the bracket on the Right Handrail (41) into the
upper end of the Right Upright (104). Attach the Right
Handrail with two 1” Bolts (43), two 1/4” Washers (44),
two 1/4” Star Washers (45), a 4” Bolt (117), and a 5/16”
Washer (122) as shown.
Do not tighten the Bolts yet.
See drawing 5a. Insert the included nylon tie through the
indicated hole in the Right Handrail (41).
See drawing 5b. Look into the Right Handrail (41) and
make sure that the Wire Harness (65) is secured to the
side shown. Tighten the nylon tie and cut the excess off
the end.
Attach the Left Handrail (not shown) in the same way.
Note: You may need to tip the Left Handrail to one side
as you insert the bracket into the top of the Left Upright.
There is not a wire harness in the Left Upright.
4. Attach the Latch Housing (46) to the Left Upright (47)
with two 3/4” Screws (38). Make sure that the large hole
in the Latch Housing is on the side shown.
Remove the Latch Knob (48) from the Latch Pin (52).
Make sure that the Latch Pin Collar (49) and the Spring
(50) are on the Latch Pin. Insert the Latch Pin into the
Storage Latch (46), and then tighten the Latch Knob
back onto the Latch Pin.
46
38
52
50
47
Large Hole
48
49
4
3.
Open part bag B.
Hold an Upright Spacer (59) against
one side of the Frame (96) as shown. Insert a 3 1/2” Bolt
(54) into the indicated hole in the Upright Spacer and the
Frame. Next, tighten a 3/4” Tek Screw (9) into the
Upright Spacer and the Frame. Remove the 3 1/2” Bolt.
Repeat on the other side of the Frame.
Have a second person lift the front end of the Frame
(96). Insert a 3 1/2” Bolt (54) with a 3/8” Star Washer (55)
into the Right Upright (104) and the right Upright Spacer
(59), and tighten the Bolt into the Frame.
Do not over-
tighten the Bolt.
Repeat on the left side of the Frame.
3
55
96
Hole
54
104
9
59
65
43
44
104
45
43
44
45
41
41
117
122
Large
Hole
Bracket
5
5a
5b
Tie
Tie
65
41