Weslo Cadence 935 Treadmill Canadian English Manual - Page 6

Place the Console Base 52 on the Left and Right

Get Weslo Cadence 935 Treadmill PDF manuals and user guides View all Weslo Cadence 935 Treadmill manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

3. Insert the bracket on the Left Handrail (61) into the left Upright (59). Whilst a second person holds the Console Base (52), carefully insert the Right Handrail (60) into the right Upright (59). Make sure that the lower ends of the Handrails (61, 60) are on the inside of the Base Legs (64) (refer to the inset drawing). Loosely thread an Upright Bolt (48) with an Upright Washer (38) into each Upright (59). Refer to the inset drawing. Insert a Handrail Bolt (71) with a Base Leg Washer (70) into the right Base Leg (64) and the Right Handrail (60). Loosely thread a Flange Nut (9) onto the Handrail Bolt. Repeat this step with the Left Handrail (not shown). 4. Place the Console Base (52) on the Left and Right Handrails (61, 60). Insert the excess Wire Harness (not shown) into the top of the right Upright (59), as you pull the excess Wire Harness (76) out of the bottom of the Upright (see drawing 6). Attach the Console Base with four Console Screws (47). Tighten all parts used in assembly step 3. 5. Attach the Left Frame Guide (86) and the Frame Guide Spacer (14) to the left side of the Frame (87) with four Latch Screws (47) as shown. Note: Be careful not to overtighten the Screws. Make sure that the notched end of the Frame Guide is at the bottom. 3 52 61 Bracket 76 60 48 38 59 59 48 38 60 9 64 4 61 60 47 5 86 47 14 87 Notched End 70 71 52 47 59 6. The console requires two "AA" batteries (not includ- 6 ed); alkaline batteries are recommended. Open the Battery Cover (56) as shown. Insert two batteries into the battery compartment, with the negative (-) ends of the batteries touching the springs. Close the battery cover, push up on the battery cover tab, and then push the tab forward as shown in the inset 56 drawing. Be sure that the tab locks into place. Batteries Battery Cover Tab 7. Make sure that all parts are properly tightened before you use the treadmill. Note: Some parts may be left over after assembly is completed. Save the included allen wrench for adjusting the walking belt. To protect the floor or carpet from damage, place a mat under the treadmill. 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
3.
Insert the bracket on the Left Handrail (61) into the
left Upright (59). Whilst a second person holds the
Console Base (52), carefully insert the Right
Handrail (60) into the right Upright (59).
Make sure
that the lower ends of the Handrails (61, 60) are
on the inside of the Base Legs (64) (refer to the
inset drawing).
Loosely thread
an Upright Bolt (48) with an Upright
Washer (38) into each Upright (59).
Refer to the inset drawing. Insert a Handrail Bolt
(71) with a Base Leg Washer (70) into the right Base
Leg (64) and the Right Handrail (60).
Loosely
thread
a Flange Nut (9) onto the Handrail Bolt.
Repeat this step with the Left Handrail (not shown).
4.
Place the Console Base (52) on the Left and Right
Handrails (61, 60). Insert the excess Wire Harness
(not shown) into the top of the right Upright (59), as
you pull the excess Wire Harness (76) out of the
bottom of the Upright (see drawing 6). Attach the
Console Base with four Console Screws (47).
Tighten all parts used in assembly step 3.
5. Attach the Left Frame Guide (86) and the Frame
Guide Spacer (14) to the left side of the Frame (87)
with four Latch Screws (47) as shown. Note: Be
careful not to overtighten the Screws.
Make sure
that the notched end of the Frame Guide is at the
bottom.
6.
The console requires two "AA" batteries (not includ-
ed); alkaline batteries are recommended. Open the
Battery Cover (56) as shown. Insert two batteries
into the battery compartment,
with the negative (–)
ends of the batteries touching the springs.
Close
the battery cover, push up on the battery cover tab,
and then push the tab forward as shown in the inset
drawing. Be sure that the tab locks into place.
5
4
6
14
87
47
86
Notched End
47
61
47
60
59
52
6
38
38
48
52
59
59
61
60
76
Bracket
48
3
Battery Cover Tab
Batteries
56
70
64
60
71
9
7.
Make sure that all parts are properly tightened before you use the treadmill.
Note: Some parts may be
left over after assembly is completed. Save the included allen wrench for adjusting the walking belt. To protect
the floor or carpet from damage, place a mat under the treadmill.