Weslo Cadence Dl35 English Manual - Page 10

Nut. The Leg Lever must pivot freely.

Get Weslo Cadence Dl35 PDF manuals and user guides View all Weslo Cadence Dl35 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

10. Lubricate the 3/8" x 2 1/4" Bolt (10). Attach the Leg Lever (14) to the Bench Frame (5) with the Bolt and a 3/8" Jam Nut (11). Do not overtighten the Jam Nut. The Leg Lever must pivot freely. 10 14 10 5 11 11. Tap two 3/4" Inner Caps (12) into each Pad Tube 11 (20). Insert the Pad Tubes (20) through the holes in the Leg Lever (14). Center the Pad Tubes and slide two Foam Pads (12) onto each Pad Tube. 12 13 14 12. Attach a Backrest Bracket (2) to the Backrest (1) 12 with two 1/4" x 3/4" Screws (3). Make sure that the Backrest Bracket is oriented as shown. Do not tighten the Screws yet. 12 20 13 3 2 3 1 13. Refer to drawing 13a. Hold the Backrest (1) in a vertical position as shown and slide the end of the attached Backrest Bracket (2) onto the welded rod on the Bench Frame (5). Hold the other Backrest Bracket (2) at an angle as shown and slide it onto the rod. Refer to drawing 13b. Attach the Backrest Bracket (2) to the Backrest (1) with two 1/4" x 3/4" Screws (3). Note: The Screw nearest the rod should be attached first. Fully tighten all four 1/4" x 3/4" Screws (3) used 10 in steps 12 and 13. 13a 2 13b 1 2 Rod 5 3 2 1 3 Rod

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
10
11.
Tap two 3/4” Inner Caps (12) into each Pad Tube
(20).
Insert the Pad Tubes (20) through the holes in the
Leg Lever (14). Center the Pad Tubes and slide two
Foam Pads (12) onto each Pad Tube.
10.
Lubricate the 3/8” x 2 1/4” Bolt (10). Attach the Leg
Lever (14) to the Bench Frame (5) with the Bolt and
a 3/8” Jam Nut (11).
Do not overtighten the Jam
Nut. The Leg Lever must pivot freely.
10
14
5
10
11
11
14
13
12
20
13
12
12.
Attach a Backrest Bracket (2) to the Backrest (1)
with two 1/4” x 3/4” Screws (3).
Make sure that the
Backrest Bracket is oriented as shown. Do not
tighten the Screws yet.
13.
Refer to drawing 13a. Hold the Backrest (1) in a
vertical position as shown and slide the end of the
attached Backrest Bracket (2) onto the welded rod
on the Bench Frame (5). Hold the other Backrest
Bracket (2) at an angle as shown and slide it onto
the rod.
Refer to drawing 13b. Attach the Backrest Bracket
(2) to the Backrest (1) with two 1/4” x 3/4” Screws
(3).
Note: The Screw nearest the rod should be
attached first.
Fully tighten all four 1/4” x 3/4” Screws (3) used
in steps 12 and 13.
13a
1
12
1
3
3
2
1
3
2
5
Rod
Rod
3
2
2
13b