Weslo Pursuit 5.0r Bike English Manual - Page 15

Maintenance And Troubleshooting

Get Weslo Pursuit 5.0r Bike PDF manuals and user guides View all Weslo Pursuit 5.0r Bike manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

MAINTENANCE AND TROUBLESHOOTING Inspect and tighten all parts of the exercise cycle regularly. Replace any worn parts immediately. To clean the exercise cycle, use a damp cloth and a small amount of mild detergent. IMPORTANT: To avoid damage to the console, keep liquids away from the console and keep the console out of direct sunlight. BATTERY REPLACEMENT If the console display becomes dim, the batteries should be replaced; most console problems are the result of low batteries. To replace the batteries, see assembly step 8 on page 9. HOW TO ADJUST THE REED SWITCH If the console does not display correct feedback, the reed switch should be adjusted. In order to adjust the reed switch, you must first remove the left pedal and the left side shield. Using an adjustable wrench, turn the left pedal clockwise and remove it. Next, remove the screws from the left side shield. Then, carefully remove the left side shield. HOW TO ADJUST THE BELT If you can feel the pedals slip while you are pedaling, even when the resistance is at the highest level, the belt may need to be adjusted. To adjust the belt, first remove the left pedal and the left side shield. Using an adjustable wrench, turn the left pedal clockwise and remove it. Next, remove the screws from the left side shield. Next, loosen the two 3/8" Locknuts (32), one on each side of the Flywheel (37). Then, tighten the M6 Nylon Locknuts (63), one on each side of the Flywheel, until the belt is properly tightened. Finally, tighten the 3/8" Nylon Locknuts. Then, reattach the side shield covers. 32 37 63 21 43 47 38 With the left side shield removed, locate the Reed Switch (43). Turn the Crank (21) until the Magnet (38) is aligned with the Reed Switch. Next, loosen, but do not remove, the indicated M3 x 10mm Screw (47). Slide the Reed Switch slightly closer to or away from the Magnet, and then retighten the Self-tapping Screw. Turn the Crank for a moment. Repeat these actions until the console displays correct feedback. When the Reed Switch is correctly adjusted, reattach the left side shield and the left pedal. 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
15
Inspect and tighten all parts of the exercise cycle reg-
ularly. Replace any worn parts immediately.
To clean the exercise cycle, use a damp cloth and a
small amount of mild detergent.
IMPORTANT: To
avoid damage to the console, keep liquids away
from the console and keep the console out of
direct sunlight.
BATTERY REPLACEMENT
If the console display becomes dim, the batteries
should be replaced; most console problems are the
result of low batteries. To replace the batteries, see
assembly step 8 on page 9.
HOW TO ADJUST THE REED SWITCH
If the console does not display correct feedback, the
reed switch should be adjusted. In order to adjust the
reed switch, you must first remove the left pedal and
the left side shield. Using an adjustable wrench, turn
the left pedal clockwise and remove it. Next, remove
the screws from the left side shield. Then, carefully
remove the left side shield.
With the left side shield removed, locate the Reed
Switch (43). Turn the Crank (21) until the Magnet (38)
is aligned with the Reed Switch. Next, loosen, but do
not remove, the indicated M3 x 10mm Screw (47).
Slide the Reed Switch slightly closer to or away from
the Magnet, and then retighten the Self-tapping Screw.
Turn the Crank for a moment. Repeat these actions
until the console displays correct feedback. When the
Reed Switch is correctly adjusted, reattach the left
side shield and the left pedal.
HOW TO ADJUST THE BELT
If you can feel the pedals slip while you are pedaling,
even when the resistance is at the highest level, the
belt may need to be adjusted.
To adjust the belt, first remove the left pedal and the
left side shield. Using an adjustable wrench, turn the
left pedal clockwise and remove it. Next, remove the
screws from the left side shield.
Next, loosen the two 3/8" Locknuts (32), one on each
side of the Flywheel (37). Then, tighten the M6 Nylon
Locknuts (63), one on each side of the Flywheel, until
the belt is properly tightened. Finally, tighten the 3/8"
Nylon Locknuts. Then, reattach the side shield covers.
MAINTENANCE AND TROUBLESHOOTING
38
43
47
21
63
37
32