Weslo Pursuit 695i English Manual - Page 13

adjustable

Page 13 highlights

HOW TO ADJUST THE RESISTANCE STRAP If there is not enough pedaling resistance when the resistance knob is turned to the highest setting, the Resistance Strap (47) may need to be adjusted. To adjust the Resistance Strap, the left side shield must first be removed. Refer to the Instructions at the left and remove the left side shield. Next, turn the resistance knob to the lowest setting. Locate and open the Strap Buckle 33 47 (46). Grip the end of the Resistance Strap (47) and 46 pull It up to remove any slack. While holding the end of the Resistance Strap, fully close the Strap Buckle. Turn the Crank (33) for a moment to make sure that there Is not too much resistance. When the Resistance Strap is properly adjusted, reattach the left side shield and pedal. HOW TO ADJUST THE BELT The exercise cycle features a belt that must be kept properly adjusted. If the belt causes excessive noise or slips as you pedal, the belt should be checked. To do this, the left side shield must first be removed. Refer to the instructions on page 12 and remove the left side shield. Next, use an adjustable wrench to turn the right pedal 16 counterclock- wise and remove it. Remove the right side shield. Press down on the center of the Belt (16) between the front and rear pulleys. There should be from 1/4" to 1/2" of vertical movement In the center of the Belt. If the Belt (16) is properly adjusted, reat- 16 tach the side shields and ped- als. If the Belt 39 needs to be adjusted, loosen the M8 Washer Nut (34) on 37 each side of the Flywheel (39). To tighten the Belt, turn the two M6 Nuts (37) clock- wise; to loosen the Belt, turn the Nuts counterclock- wise. Make sure that the Flywheel is straight and tight- en the M8 Washer Nuts (34). Reattach the side shields and pedals. 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16

HOW
TO
ADJUST
THE
RESISTANCE
STRAP
If
there
is
not
enough
pedaling
resistance
when
the
resistance
knob
is
turned
to
the
highest
setting,
the
Resistance
Strap
(47)
may
need
to
be
adjusted.
To
adjust
the
Resistance
Strap,
the
left
side
shield
must
first
be
removed.
Refer
to
the
Instructions
at
the
left
and
remove
the
left
side
shield.
Next,
turn
the
resistance
knob
to
the
lowest
setting.
Locate
and
open
the
33
Strap
Buckle
(46).
Grip
the
end
of
the
Resistance
Strap
(47)
and
46
pull
It
up
to
remove
any
slack.
While
holding
the
end
of
the
Resistance
Strap,
fully
close
the
Strap
Buckle.
Turn
the
Crank
(33)
for
a
moment
to
make
sure
that
there
Is not
too
much
resistance.
When
the
Resistance
Strap
is
properly
adjusted,
reattach
the
left
side
shield
and
pedal.
HOW
TO
ADJUST
THE
BELT
47
The
exercise
cycle
features
a
belt
that
must
be
kept
properly
adjusted.
If
the
belt
causes
excessive
noise
or
slips
as
you
pedal,
the
belt
should
be
checked.
To
do
this,
the
left
side
shield
must
first
be
removed.
Refer
to
the
instructions
on
page
12
and
remove
the
left
side
shield.
Next,
use
an
adjustable
wrench
to
turn
the
right
pedal
counterclock-
wise
and
remove
it.
Remove
the
right
side
shield.
Press
down
on
the
center
of
the
Belt
(16)
between
the
front
and
rear
pulleys.
There
should
be
from
1/4"
to
1/2"
of
vertical
movement
In
the
center
of
the
Belt.
16
If
the
Belt
(16)
is
properly
adjusted,
reat-
tach
the
side
shields
and
ped-
als.
If
the
Belt
needs
to
be
adjusted,
loosen
the
M8
Washer
Nut
(34)
on
each
side
of
the
Flywheel
(39).
To
tighten
the
Belt,
turn
the
two
M6
Nuts
(37)
clock-
wise;
to
loosen
the
Belt,
turn
the
Nuts
counterclock-
wise.
Make
sure
that
the
Flywheel
is
straight
and
tight-
en
the
M8
Washer
Nuts
(34).
Reattach
the
side
shields
and
pedals.
16
39
37
13