Weslo Wetl39710 Instruction Manual - Page 12

Important: If

Get Weslo Wetl39710 PDF manuals and user guides View all Weslo Wetl39710 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

4. Follow your progress with the displays. The track-The track represents a distance of 1/4 mile (402 meters). As you walk or run on the treadmill, the indicators around the track will appear in succession until the entire track appears. The track will then disappear and the indicators will again begin to appear in succession.  The left display-As you exercise, the left display can show the elapsed time and the approximate number of calories that you have burned. The display also shows your heart rate when you use the pulse sensor (see step 5 on this page). Note: When you use a preset workout, the left display will show the time remaining in the workout instead of the elapsed time. The right display-The right display can show the speed of the walking belt and the distance that you have walked or run. To reset the displays, press the Stop button, remove the key, and then reinsert the key. 5. Measure your heart rate if desired. To measure your heart rate, stand on the foot rails and place your thumb on the pulse sensor (see the drawing on page 10). Do not press too hard, or the circulation in your thumb will be restricted and your pulse may not be detected. When your pulse is detected, the small heart symbol in the left display will flash and your heart rate will be shown. For the most accurate heart rate reading, hold your thumb on the pulse sensor for at least 15 seconds. If the displayed heart rate appears to be too high or too low, or if your heart rate is not displayed, lift your thumb for a few seconds, and then reposition your thumb on the pulse sensor. Remember to stand still while measuring your heart rate. 6. When you are finished exercising, remove the key from the console. Step onto the foot rails, press the Stop button, remove the key from the console, and put it in a secure place. When you are finished using the treadmill, press the power switch into the off position and unplug the power cord. IMPORTANT: If you do not do this, the treadmill's electrical components may wear prematurely. 1122

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
12
12
4.
Follow your progress with the displays.
The track—
The track
represents a distance of
1/4 mile (402 meters).
As you walk or run on
the treadmill, the indica-
tors around the track will
appear in succession until the entire track appears.
The track will then disappear and the indicators will
again begin to appear in succession.
The left display—
As
you exercise, the left
display can show the
elapsed time and the
approximate number of
calories that you have
burned. The display also shows your heart rate
when you use the pulse sensor (see step 5 on
this page). Note: When you use a preset workout,
the left display will show the time remaining in the
workout instead of the elapsed time.
The right display—
The
right display can show
the speed of the walking
belt and the distance
that you have walked or
run.
To reset the displays, press the Stop button,
remove the key, and then reinsert the key.
5.
Measure your heart rate if desired.
To measure your heart rate,
stand on the foot
rails
and place your thumb on the pulse sensor
(see the drawing on page 10).
Do not press too
hard, or the circulation in your thumb will be
restricted and your pulse may not be detected.
When your pulse is detected, the small heart sym-
bol in the left display will flash and your heart rate
will be shown.
For the most accurate heart rate
reading, hold your thumb on the pulse sensor
for at least 15 seconds.
If the displayed heart rate appears to be too high
or too low, or if your heart rate is not displayed, lift
your thumb for a few seconds, and then reposi-
tion your thumb on the pulse sensor. Remember to
stand still while measuring your heart rate.
6.
When you are finished exercising, remove the key
from the console.
Step onto the foot rails, press the Stop button,
remove the key from the console, and put it in a
secure place. When you are finished using the
treadmill, press the power switch into the off posi-
tion and unplug the power cord.
IMPORTANT: If
you do not do this, the treadmill’s electrical
components may wear prematurely.