Whirlpool GZ7936XHS Dimension Guide - Page 1
Whirlpool GZ7936XHS Manual
View all Whirlpool GZ7936XHS manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
® Retractable Downdraft Vent System PRODUCT MODEL NUMBERS GZ7930XG GZ7930XH GZ7936XG GZ7936XH Electrical: 120-volt, 60-Hz, AC-only, 15 amp electrical supply. Use copper wire only. A timedelay fuse or circuit breaker and separate circuit is recommended. OVERALL DIMENSIONS 8-1/4" (21 cm) retractable vent height top trim widths 30" vent (76.2 cm) 36" vent (91.4 cm) 4" (10.2 cm) 27" (68.6 cm) for 30" (76.2 cm) vent 33" (83.8 cm) for 36" (91.4 cm) vent 1-1/2" (3.8 cm) 3/8" (9.5 mm) 16" (40.6 cm) EXTERIOR-MOUNTED BLOWER MOTOR 8" (20.3 cm) For use with Model No. KPEC992M [900 cfm (25.5 m3/m)] only 9" (22.9 cm) Diameter CABINET OPENING DIMENSIONS 8" (20,3 cm) 16" (40.6 cm) See cooktop manufacturer's instructions for cooktop cutout depth and width. Use dimensions for vent system cutout location that applies to your installation. A = 1/2" (12.7 mm) min. 23-9/16" (59.8 cm) 17-3/16" (43.7 cm) 5/8" (15.9 mm) 3-1/4"x 10" (8.3 cm x 25.4 cm) 16" (40.6 cm) INTERNAL 16" BLOWER (40.6 cm) MOTOR 9-3/8" (23.8 cm) 26-1/8" (66.4 cm) 5/8" (15.9 mm) 2-1/8" (54 cm) 4-1/8"+A (10.5 cm) 17-9/16" (44.6 cm) Maximum length of vent system Vent 6" (15.2 cm) round 3-1/4" x 10" (8.3 cm x 25.4 cm) Length 35 feet (8.9 m) 35 feet (8.9 m) For best performance, use no more than three 90° elbows. If more than one elbow is used, make sure that there is a minimum of 24" (61 cm) of straight vent between any two elbows. Do Not install two elbows together. It is recommended that you use round vent instead of rectangular vent, especially if elbows are required. If rectangular vent is required, it should be transitioned to 6" (15.2 cm) round vent as soon as possible. all cutouts shown are for 3-1/4" x 10" (8.3 cm x 25.4 cm) vent system 3/8" (9.5 mm) Locate power supply junction box at lower right hand rear corner of cabinet. centerline of cooktop cutout Vent system cutout dimensions for internal blower models only. Exterior mounted blower systems connect with 10" (25.4 cm) round vent. The cutout locations for this vent system will depend upon your specific installation. Determining the length of system you need: To calculate the length of system you need, add the equivalent feet for each vent piece that will be needed. See example for 6" (15.2 cm) round vent system. Because Whirlpool Corporation policy includes a continuous commitment to improve Dimensions are for planning purposes only. For complete details, see Installation Ref. 8284826 Rev. B our products, we reserve the right to change materials and specifications without notice. Instructions packed with product. Specifications subject to change without notice. 10-20-03