Whirlpool KEBC208KSS Installation Instructions - Page 4
Whirlpool KEBC208KSS Manual
View all Whirlpool KEBC208KSS manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 4 highlights
B Electrical connection If your house has aluminum wiring, see "Electrical requirements", Page 2. cable from power supply junction box red wires white wire black wires cable from power supply junction box red wires white wires WARNING Electrical Shock Hazard Turn power supply off before connecting wires. Use 8 gauge solid copper wire. Electrically ground range. Failure to follow these instructions can result in death, fire, or electrical shock. This oven is manufactured with white (neutral) power supply wire and a cabinet-connected bare grounding wire twisted together. white and bare grounding oven cable wires - factory crimped Figure 1 cable from oven U.L.-listed conduit connector bare grounding wires black wires cable from oven U.L.-listed conduit connector Figure 2 If local codes PERMIT connecting cabinetgrounding conductor to neutral white wire in junction box: 7. Connect the factory-crimped bare and white oven cable wires to the neutral (white) wire in junction box. See Figure 1. 8. Replace junction box cover. If local codes DO NOT PERMIT connecting cabinet-grounding conductor to neutral white wire in junction box: 7. Separate the factorycrimped bare and white oven cable wires. 8. Connect white oven cable wire to neutral (white) wire in junction box. See Figure 2. 9. Connect the bare grounding oven cable wire to a grounded wire in the junction box. See Figure 2. 10. Replace junction box cover. If connecting to a four-wire electrical system: 7. Separate bare and white oven cable wires. 8. Connect white oven cable wire to neutral (white) wire in junction box. See Figure 2. 9. Connect the bare grounding oven cable wire to the green grounding wire in junction box. Do Not connect bare grounding wire to neutral (white) wire in junction box. See Figure 2. 10. Replace junction box cover. 4. Feed oven cable through opening in the cabinet. Make electrical connection following the steps needed for your installation. 1. Disconnect the power supply. 2. Remove the junction box cover. 3. Connect oven cable to junction box through the U.L.-listed conduit connector. 4. Connect the two black wires together with twist-on connectors. 5. Connect the two red wires together with twist-on connectors. 6. Complete electrical connection according to local codes and ordinances. C Attachment Carefully push against seal area of oven front frame when pushing oven into cabinet. Do Not push against outside edges. 4 screws Slide top of trim up. Push trim into place. Replace trim screw. Lift oven into cabinet cutout using the oven opening as an area to grip. 5. 7. Slide top end of each trim upward onto oven side rails. Push each trim into place at bottom of trim. Use screws to attach each trim to oven. Take care not to scratch other surfaces with ends of trim. 8. shipping foot Replace oven racks. Important: Securely fasten oven to cabinet using the screws provided (two screws for a single oven or four screws for a double oven). Insert the screws through holes in mounting rails. Do Not overtighten screws. 6. Push against seal area of front frame to push oven into cabinet until shipping feet almost contact cabinet. Use a Phillips screwdriver to remove screws attaching shipping feet. Remove and discard shipping feet. Push oven completely into cabinet and center oven in cabinet cutout. Reinstall the oven door by inserting ends of hinges into hinge slots in the oven frame. Push hinges in as far as they will go. Open the door (you will feel the door drop into place) and rotate both hinge latches back to the locked position. Close and open the door to check that the door closes and opens completely. If door does not close or open completely, repeat the door removal step and reinstall door as described above. Repeat for lower oven door. 9. D Check operation 10. 11. Page 3 Make sure the oven door is closed and the "ON" light is shown in the display area. After 2 minutes, partially open oven door. You should feel heat from the oven. Press the "CANCEL" pad. Check the operation of your double oven. Press the "Upper Oven" pad. Press the "BROIL" pad. "BROIL" will appear in the display. Press the "START" pad. Make sure the oven door is closed and the "ON" light is shown in the display area. After 2 minutes, partially open oven door. You should feel heat from the oven. Press the "CANCEL" pad. Press the "Lower Oven" pad and repeat the steps you completed for checking the upper oven. If your oven does not heat or an "F", followed by a number, appears in the display, contact your dealer or check the "If you need service..." section of this Installation Instructions. Turn on power supply. The display panel will light up briefly. "PF" should appear in the temperature display. BAKE BROIL CLEAN Check the operation of your single oven. Press the "BROIL" pad. "BROIL" will appear in the display. Press the "START" pad. To get the most efficient use from your new oven, read your Use and Care Guide. Keep Installation Instructions and Guide close to oven for easy reference.