Whirlpool LER3622PQ Dimension Guide - Page 1

Whirlpool LER3622PQ - 3.4 cu. Ft. Electric Dryer Manual

Get Whirlpool LER3622PQ - 3.4 cu. Ft. Electric Dryer PDF manuals and user guides
UPC - 050946958712
View all Whirlpool LER3622PQ manuals
Add to My Manuals
Save this manual to your list of manuals

Page 1 highlights

® Electric Compact Dryer PRODUCT MODEL NUMBERS LER3622P OVERALL DIMENSIONS Electrical: A four-wire or three-wire, single phase, 120/240-volt, 60-Hz, AC-only, electrical supply (or 120/208-volt electrical supply, if specified on the serial/rating plate) is required on a separate 30-amp circuit, fused on both sides of the line. A time-delay fuse or circuit breaker is recommended. Exhaust venting: Exhaust your dryer to the outside. Four-inch diameter vent is required. Rigid or flexible metal exhaust vent must be used. Do Not use plastic or metal foil vent. Exhaust outlet hood must be at least 12 inches from the ground or any object that may be in the path of the exhaust. *Most installations require a minimum 5¹⁄₂" (14.0 cm) clearance behind the dryer for the exhaust vent with elbows. *20 3 4" (52.7 cm) 31"† (78.7 cm) 23 7 8" (60.6 cm) RECESSED AREA AND CLOSET INSTALLATION Recessed or closet installation - Dryer only Recessed or closet installation - Stacked Closet confined area 14" (35.6 cm) 18" (45.7cm) 12" (30.5 cm) 12" (30.5 cm) 3" 0"* 0"* (7.6 cm) (0cm) (0 cm) A B 0"* (0 cm) A. Side view - closet or confined area B. Recessed area *Additional spacing recommended DRYER 3" (7.6 cm) WASHER 0"* 1" (0 cm) (2.5 cm) A B 48 in.2 (309.7 cm2) 24 in.2 (154.8 cm2) 3" For closet installation (7.6 cm) with a door, minimum ventilation openings in the top and bottom of the door are required. Louvered doors with equivalent ventilation openings are acceptable. 3" (7.6 cm) C A. Recessed area B. Side view - closet or confined area C. Closet door with vents EXHAUST VENTING Recommended hood styles B A Angled hood style is acceptable. 4" (10.2 cm) Vent system chart Number of 90º turns or elbows Type of vent Box or louvered hoods Angled hoods 4" (10.2 cm) 4" (10.2 cm) A. Louvered hood style B. Box hood style 2.5" 0 (6.4 cm) 1 2 Select the route that will provide the straightest and most direct path outdoors. Plan the installation to use the fewest number of elbows and turns. Use the fewest 90° turns possible. Do not use vent runs longer than specified in vent length chart. Determine the number of elbows you will need. Rigid metal 36 ft (11 m) Flexible metal 28 ft (8.5 m) Rigid metal 26 ft (7.9 m) Flexible metal 18 ft (5.5 m) Rigid metal 16 ft (4.9 m) Flexible metal 8 ft (2.8 m) 26 ft (7.9 m) 22 ft (6.7 m) 16 ft (4.9 m) 12 ft (3.7 m) 6 ft (1.8 m) 2 ft (0.6 m) Because Whirlpool Corporation policy includes a continuous commitment to improve Dimensions are for planning purposes only. For complete details, see Installation our products, we reserve the right to change materials and specifications without notice. Instructions packed with product. Specifications subject to change without notice. Ref. 8577196 08-24-05

  • 1
®
Electric Compact Dryer
PRODUCT MODEL NUMBERS
OVERALL DIMENSIONS
RECESSED AREA AND CLOSET INSTALLATION
EXHAUST VENTING
LER3622P
Electrical:
A four-wire or three-wire, single
phase, 120/240-volt, 60-Hz, AC-only, electrical
supply (or 120/208-volt electrical supply, if
specified on the serial/rating plate) is required on a
separate 30-amp circuit, fused on both sides of the
line. A time-delay fuse or circuit breaker is
recommended.
Exhaust venting:
Exhaust your dryer to the
outside. Four-inch diameter vent is required. Rigid
or flexible metal exhaust vent must be used. Do
Not use plastic or metal foil vent. Exhaust outlet
hood must be at least 12 inches from the ground
or any object that may be in the path of the
exhaust.
Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only.
For complete details, see Installation
Instructions packed with product.
Specifications subject to change without notice.
Ref. 8577196
08-24-05
23
7
8
(60.6 cm)
"
20
3
4
(52.7 cm)
"
31"
†
(78.7 cm)
*
Recessed or closet installation - Dryer only
*Additional spacing recommended
Recessed or closet installation - Stacked
A. Side view - closet or confined area
B. Recessed area
A. Recessed area
B. Side view - closet or confined area
C. Closet door with vents
A
B
3"
(7.6cm)
14"
(35.6cm)
18" (45.7cm)
0"*
(0cm)
0"*
(0cm)
DRYER
WASHER
(7.6 cm)
3"
(30.5 cm)
12"
(30.5 cm)
12"
0"*
(0 cm)
0"*
(0 cm)
A
B
C
1"
(2.5 cm)
3"
(7.6 cm)
48 in.
2
(309.7 cm )
2
24 in.
2
(154.8 cm )
2
3"
(7.6 cm)
Vent system chart
Number of
90º turns
or elbows
Type of
vent
Box or
louvered
hoods
Angled
hoods
0
Rigid metal
Flexible metal
36 ft (11 m)
28 ft (8.5 m)
26 ft (7.9 m)
22 ft (6.7 m)
1
Rigid metal
Flexible metal
26 ft (7.9 m)
18 ft (5.5 m)
16 ft (4.9 m)
12 ft (3.7 m)
2
Rigid metal
Flexible metal
16 ft (4.9 m)
8 ft (2.8 m)
6 ft (1.8 m)
2 ft (0.6 m)
Closet confined area
For closet installation
with a door, minimum
ventilation openings
in the top and bottom
of the door are
required. Louvered
doors with equivalent
ventilation openings
are acceptable.
*Most installations require a
minimum 5
¹⁄₂
" (14.0 cm)
clearance behind the dryer for
the exhaust vent with elbows.
Select the route that will provide the straightest and most direct path
outdoors. Plan the installation to use the fewest number of elbows and turns.
Use the fewest 90° turns possible.
Do not use vent runs longer than specified in vent length chart.
Determine the number of elbows you will need.
A. Louvered hood style
B. Box hood style
4"
(10.2 cm)
4"
(10.2 cm)
A
B
4"
(10.2 cm)
2.5"
(6.4 cm)
Recommended hood styles
Angled hood style
is acceptable.