Whirlpool WEE750H0HV Internet Connectivity Guide - Page 2
Connected Appliance Regulatory Notices - manual
View all Whirlpool WEE750H0HV manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 2 highlights
Connected Appliance Regulatory Notices Federal Communications Commission (FCC) Compliance Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. Le émetteurs radio IC : 10248A-WICHAM01 et 10248A-FLDAAM01 ont été approuvés par Industrie Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur. Type d'antenne Gain admissible L'impédance maximal d'antenne (dBi) requise (OHM) À fentes 1,2 50 Monopôle (WICHAM01 0,5 50 seulement) Dipole 3,0 50 F 1,60 50 Planaire F 4,2 50 Pour satisfaire aux exigences de la FCC et IC d'exposition aux radiofréquences, une distance de séparation de 20 cm ou plus doit être maintenue entre cet appareil et des personnes lors de fonctionnement du dispositif. Pour assurer la conformité des opérations au plus près que cette distance n'est pas recommandée. L'antenne utilisée pour ce transmetteur ne doit pas être co-localisés en conjonction avec toute autre antenne ou transmetteur. RF Exposure Information To comply with FCC/IC RF exposure requirements for mobile transmitting devices, this transmitter should only be used or installed at locations where OEM Responsibilities to comply with FCC and Industry Canada Regulations there is at least 20 cm separation distance between the antenna and all The WICHAM01 / FLDAAM01 Modules have been certified for integration persons. into products only by OEM integrators under the following conditions: To comply with FCC/IC RF exposure limits for general 1. The antenna(s) must be installed such that a minimum separation population/uncontrolled exposure, the antenna(s) used for this transmitter distance of 20 cm is maintained between the radiator (antenna) and all must be installed to provide a separation distance of at least 20 cm from all persons at all times. persons and must not be co-located or operating in conjunction with any 2. The transmitter module must not be co-located or operating in other antenna or transmitter. conjunction with any other antenna or transmitter. As long as the two conditions above are met, further transmitter testing will Industry Canada (IC) Compliance Notice This Device complies with Industry Canada License-exempt RSS standard(s). Operation is subject to the following two conditions: 1. This device may not cause interference, not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). 2. This device must accept any interference, including interference that may cause undesired operation of the device. Under Industry Canada regulations, this radio transmitter may only operate IMPORTANT NOTE: In the event that these conditions cannot be met (for certain configurations or co-location with another transmitter), then the using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the FCC and Industry Canada authorizations are no longer considered valid and the FCC ID and IC Certification Number cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re- equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. evaluating the end product (including the transmitter) and obtaining a separate FCC and Industry Canada authorization. The radio transmitters IC: 10248A-WICHAM01 and 10248A-FLDAAM01 have been approved by Industry Canada to operate with the antenna types End Product Labeling listed below with the maximum permissible gain and required antenna The WICHAM01 / FLDAAM01 Modules are labeled with FCC ID and IC impedance for each antenna type indicated. Antenna types not included in Certification Number. If the FCC ID and IC Certification Number are not this list, having a gain greater than the maximum gain indicated for that type, visible when the module is installed inside another device, then the outside are strictly prohibited for use with this device. of the device into which the module is installed must also display a label Antenna Type Maximum Permissible Required referring to the enclosed module. In that case, the final end product must be Antenna Gain (dBi) Impendance (OHM) labeled in a visible area or display the following: Slot 1.2 50 "Contains FCC ID: A5UWICHAM01" Monopole 0.5 (WICHAM01 only) Dipole 3.0 F 1.60 50 "Contains IC: 10248A-WICHAM01" or 50 "Contains FCC ID: A5UFLDAAM01" "Contains IC: 10248A-FLDAAM01" 50 The OEM of the WICHAM01 / FLDAAM01 Module must only use the Planar F 4.2 50 approved antenna(s), which have been certified with this module. The OEM To comply with FCC and Industry Canada RF radiation exposure limits for integrator has to be aware not to provide information to the end user general population, the antenna(s) used for this transmitter must be installed regarding how to install or remove this RF module or change RF related such that a minimum separation distance of 20 cm is maintained between parameters in the user manual of the end product. the radiator (antenna) and all persons at all times and must not be co- located or operating in conjunction with any other antenna or transmitter. The user manual for the end product must include the Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Conformément à la réglementation d'Industrie Canada, le présent émetteur following information in a prominent location: "To comply with FCC and Industry Canada RF radiation exposure limits for general population, the antenna(s) used for this transmitter must be installed such that a minimum separation distance of 20 cm is maintained between the radiator (antenna) and all persons at all times and must not be co- located or operating in conjunction with any other antenna or transmitter." radio peut fonctionner avec une antenne d'un type et d'un gIaninsommaeximEuarl o(opuean factories the letter "W" of the part code mentioned herein will be automatically 17-May-2017 17:39:35 EDT | RELEASED replaced by the number "4000" (e.g. "W12345678" becomes "400012345678")