Whirlpool WET4027EW Installation Guide - Page 31

Connect Vent

Get Whirlpool WET4027EW PDF manuals and user guides View all Whirlpool WET4027EW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

6. Check for leaks Connect Vent 1. C onnect vent to exhaust outlet (27" model shown) Turn on water faucets to check for leaks. A small amount of water may enter washer. It will drain later. 7. Secure drain hose Laundry Tub Standpipe Wall Connecting from front (for closet or recessed area) Connecting from rear Using a 4" (102 mm) clamp, connect vent to exhaust outlet in dryer. If connecting to existing vent, make sure vent is clean. Dryer vent must fit over dryer exhaust outlet and inside exhaust hood. Check that vent is secured to exhaust hood with a 4" (102 mm) clamp. 2. Move washer/dryer to final location 44..545"."5" (1(11134mmmm) ) 4.5" ((111134 mmmm)) 44..55"" (1143 mm) Secure drain hose to laundry tub leg, drain standpipe, or inlet hoses for wall standpipe with shipping strap removed earlier (27" models) or plastic strap included in the parts package (24" models). Move washer/dryer to final location, taking care not to crush or kink vent. After washer/dryer is in place, remove corner posts and cardboard from under washer/dryer. 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
31
Turn on water faucets to check for leaks. A small amount of
water may enter washer. It will drain later.
6.
Check for leaks
Secure drain hose to laundry tub leg, drain standpipe, or inlet
hoses for wall standpipe with shipping strap removed earlier
(27" models) or plastic strap included in the parts package
(24" models).
7.
Secure drain hose
(113 mm)
(113 mm)
Laundry Tub
Standpipe
Wall
Connect Vent
1.
Connect vent to exhaust outlet
(27" model shown)
2.
Move washer/dryer to final location
Using a 4" (102 mm) clamp, connect vent to exhaust outlet
in dryer. If connecting to existing vent, make sure vent is
clean. Dryer vent must fit over dryer exhaust outlet and inside
exhaust hood. Check that vent is secured to exhaust hood
with a 4" (102 mm) clamp.
Move washer/dryer to final location, taking care not to crush
or kink vent.
After washer/dryer is in place, remove corner posts and
cardboard from under washer/dryer.
Connecting from front
(for closet or recessed
area)
Connecting
from rear
4.5"
(114 mm)
4.5"
(114 mm)
4.5"
(114 mm)