Whirlpool WFW8620HW Owners Manual - Page 19

Cleaning Load & Go, Containers, On Some Models, Non-use And Vacation Care, Winter Storage Care,

Get Whirlpool WFW8620HW PDF manuals and user guides View all Whirlpool WFW8620HW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

CLEANING LOAD & GO™ CONTAINERS (on some models) It is recommended that you rinse out the Load & Go™ containers when refilling, when changing detergent types or concentrations, or when the washer will not be used for an extended period. 1. Pull the dispenser drawer out until it stops. 2. Lift out the Load & Go™ containers. 3. Lift the fill lid and flush interior thoroughly with warm water. TRANSPORTING YOUR WASHER 1. Shut off both water faucets. Disconnect and drain water inlet hoses. 2. If washer will be moved during freezing weather, follow "Winter Storage Care" directions before moving. 3. Disconnect drain hose from drain system and from back of washer. 4. Unplug power cord. 5. Place inlet hoses and drain hose inside washer drum. 6. Bundle power cord with a rubber band or cable tie to keep it from hanging to the ground. IMPORTANT: Call for service to install new transport bolts. Do not reuse transport bolts. Washer must be transported in the upright position. To avoid structural damage to your washer, it must be properly set up for relocation by a certified technician. 4. Allow to air dry. IMPORTANT: Containers are not dishwasher-safe. NON-USE AND VACATION CARE Operate your washer only when you are home. If moving or not using your washer for a period of time, follow these steps: 1. Unplug or disconnect power to washer. 2. Turn off water supply to washer to avoid flooding due to water pressure surges. HELPFUL TIP: Attach a reminder note to the washer to turn the water back on before washer's next use. 3. Clean the dispensers. See "Cleaning the Dispensers." WINTER STORAGE CARE IMPORTANT: To avoid damage, install and store washer where it will not freeze. Because some water may stay in hoses, freezing can damage washer. If storing or moving during freezing weather, winterize your washer. To winterize washer: 1. Shut off both water faucets; then disconnect and drain water inlet hoses. HELPFUL TIP: Attach a reminder note to the washer to turn the water back on before washer's next use. 2. Put 1 qt. (1 L) of R.V.-type antifreeze in washer drum and run washer on Normal cycle for about 2 minutes to mix antifreeze and remaining water. 3. Unplug washer or disconnect power. REINSTALLING/USING WASHER AGAIN To reinstall washer after non-use, vacation, winter storage, or moving: 1. Refer to Installation Instructions to locate, level, and connect washer. 2. Before using again, run washer through the following recommended procedure: To use washer again: 1. Flush water pipes and hoses. Reconnect water inlet hoses. Turn on both water faucets. 2. Plug in washer or reconnect power. 3. Run washer through Heavy Duty cycle to clean washer and remove antifreeze, if used. Use only HE detergent. Use half the manufacturer's recommended amount for a medium-size load. 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
19
It is recommended that you rinse out the Load & Go
™
containers when refilling, when changing detergent types or
concentrations, or when the washer will not be used for an
extended period.
1.
Pull the dispenser drawer out until it stops.
2.
Lift out the Load & Go
™
containers.
3.
Lift the fill lid and flush interior thoroughly with warm water.
4.
Allow to air dry.
IMPORTANT:
Containers are not dishwasher-safe.
CLEANING LOAD & GO
™
CONTAINERS
(on some models)
Operate your washer only when you are home. If moving
or not using your washer for a period of time, follow these
steps:
1.
±
Unplug or disconnect power to washer.
2.
±
Turn off water supply to washer to avoid flooding due
to water pressure surges.
HELPFUL TIP:
Attach a reminder note to the washer
to turn the water back on before washer’s next use.
3.
±
Clean the dispensers. See “Cleaning the Dispensers.”
NON-USE AND VACATION CARE
WINTER STORAGE CARE
IMPORTANT:
To avoid damage, install and store washer
where it will not freeze. Because some water may stay in
hoses, freezing can damage washer. If storing or moving
during freezing weather, winterize your washer.
To winterize washer:
1.
Shut off both water faucets; then disconnect and drain
water inlet hoses.
HELPFUL TIP:
Attach a reminder note to the washer
to turn the water back on before washer’s next use.
2.
Put 1 qt. (1 L) of R.V.-type antifreeze in washer drum
and run washer on Normal cycle for about 2 minutes
to mix antifreeze and remaining water.
3.
Unplug washer or disconnect power.
TRANSPORTING YOUR WASHER
1.
±
Shut off both water faucets. Disconnect and drain water
inlet hoses.
2.
±
If washer will be moved during freezing weather, follow
“Winter Storage Care” directions before moving.
3.
±
Disconnect drain hose from drain system and from back
of washer.
4.
±
Unplug power cord.
5.
±
Place inlet hoses and drain hose inside washer drum.
6.
±
Bundle power cord with a rubber band or cable tie to
keep it from hanging to the ground.
IMPORTANT:
Call for service to install new transport bolts.
Do not reuse transport bolts. Washer must be transported
in the upright position. To avoid structural damage to
your washer, it must be properly set up for relocation
by a certified technician.
REINSTALLING/USING WASHER AGAIN
To reinstall washer after non-use, vacation, winter storage,
or moving:
1.
±
Refer to Installation Instructions to locate, level, and
connect washer.
2.
±
Before using again, run washer through the following
recommended procedure:
To use washer again:
1.
±
Flush water pipes and hoses. Reconnect water inlet
hoses. Turn on both water faucets.
2.
±
Plug in washer or reconnect power.
3.
±
Run washer through Heavy Duty cycle to clean washer
and remove antifreeze, if used. Use only HE detergent.
Use half the manufacturer’s recommended amount for
a medium-size load.