Home » Whirlpool Manuals » Laundry Washers » Whirlpool WFW9050XW » Manual Viewer

Whirlpool WFW9050XW Owners Manual - Page 36

hr:min

UPC - 883049204994

View all Whirlpool WFW9050XW manuals

Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

Programmes Programmes de lavage Choisir les programmes de lavage en appuyant sur le bouton de sélection de programme jusqu'au programme désiré. Chaque programme est conçu pour différents types de tissu et niveaux de saleté. ■ Chaque programme comporte une durée, température et vitesse d'essorage préréglées et peut comporter des options préréglées. Les préréglages procurent les soins aux tissus recommandés pour le programme sélectionné. ■ Les préréglages peuvent être modifiés à tout moment avant que l'on ait appuyé sur START/PAUSE (mise en marche/ pause). Toutes les options (TEMP) ne sont pas disponibles avec tous les programmes. Pour modifier les réglages après le début d'un programme, sélectionner START/PAUSE (mise en marche/pause) puis sélectionner les réglages désirés. Appuyer sur la touche START/PAUSE (pendant environ 3 secondes) pour poursuivre le programme. Préréglages de programme Chaque programme comporte une durée, température et vitesse d'essorage préréglées. Ces réglages procurent les soins aux tissus recommandés pour le programme sélectionné. Voir le tableau. Programme Durée estimée* (hr:min) Temp. Vitesse d'essorage Heavy Duty (service intense) 1:22 Hot (chaude) High (élevée) Normal 1:12 Warm (tiède) High (élevée) Delicate (articles délicats) 0:37 Cold (froide) Low (basse) Rinse & Spin (rinçage et essorage) 0:26 Cold (froide) High (élevée) Drain & Spin (vidange et essorage) 0:14 N/A High (élevée) Clean Washer with 0:54 N/A AFFRESH™ (nettoyage de la laveuse avec AFFRESH™) High (élevée) *Les durées de programme varient automatiquement en fonction de la pression et de la température de l'eau, du détergent et de la charge de linge. La durée du programme sera prolongée en cas d'excès de mousse ou si la charge est déséquilibrée. 36 Heavy Duty (service intense) Utiliser ce programme pour laver des charges de vêtements robustes, aux couleurs grand teint et très sales. Ce programme combine un culbutage à vitesse rapide, une durée de lavage prolongée et un essorage à vitesse élevée pour réduire les durées de séchage. Normal Utiliser ce programme pour laver des charges de tissus qui ne se repassent pas tels que chemises de sport, chemisiers, vêtements de travail tout-aller, mélanges à pressage permanent, coton et linge de maison et tissus synthétiques. Ce programme combine un culbutage à vitesse moyenne, un essorage à vitesse élevée et un processus de refroidissement de la charge pour réduire le froissement. Delicate (articles délicats) Utiliser ce programme pour laver les tissus fragiles et la lingerie. Ce programme combine un culbutage à basse vitesse et un essorage à basse vitesse pour assurer un soin délicat des tissus. ■ Utiliser des sacs en filet pour laver les sous-vêtements tels que les soutiens-gorge à armature, les articles avec cordons et les articles de petite taille tels que les chaussettes. Rinse & Spin (rinçage et essorage) Utiliser ce programme pour obtenir un rinçage et un essorage seulement. Ce programme combine un culbutage à vitesse élevée et un essorage à vitesse élevée. Le programme Rinse & Spin est utile pour : ■ Les charges qui nécessitent un rinçage uniquement. ■ Ajouter de l'assouplissant de tissu à une charge en utilisant le distributeur d'assouplissant de tissu. Drain & Spin (vidange et essorage) Utiliser ce programme pour vidanger la laveuse ou pour vidanger et essorer la charge de lavage. La vitesse d'essorage est préréglée à élevée. Utilisation de Drain & Spin (vidange et essorage) : 1. Sélectionner le programme Drain & Spin (vidange et essorage).

Section	Page
Front-Loading Automatic Washer	1
Use & Care Guide	1
For questions about features, operation/performance, parts, accessories, or service, call: 1-800-253-1301	1
or visit our website at...	1
www.whirlpool.com	1
In Canada, call: 1-800-807-6777	1
or visit our website at...	1
www.whirlpool.ca	1
Laveuse Automatique À Chargement Frontal	1
Guide d'utilisation et d'entretien	1
Pour assistance, installation, ou service, composez le : 1-800-807-6777 ou visitez notre site internet à..	1
www.whirlpool.ca	1
TABLE OF CONTENTS	1
TABLE DES MATIÈRES	1
WASHer Safety	2
INSTALLATION requirements	3
Tools and Parts	3
Tools needed for connecting the water inlet hoses	3
Pliers (that open to 19/16\	3
Flashlight (optional)	3
Tools needed for connecting the drain hose	3
Locking pliers (that open to 19/16\	3
Tools needed for installation	3
Open end wrenches 14 mm and 13 mm	3
Level	3
Wood block	3
Ruler or measuring tape	3
Alternate Parts	3
Options	3
Optional pedestal	3
Location Requirements	3
A water heater set to deliver 120°F (49°C) water to the washer.	3
A grounded electrical outlet located within 6 ft. (1.8 m) of where the power cord is attached to the back of the washer. See “Electrical Requirements.”	3
Hot and cold water faucets located within 4 ft. (1.2 m) of the hot and cold water fill valves, and water pressure of 20-100 psi (137.9-689.6 kPa).	3
A level floor with a maximum slope of 1\	3
A sturdy and solid floor to support the washer with a total weight (water and load) of 400 lbs. (180 kg).	3
Installation clearances	4
The location must be large enough to allow the washer door to be fully opened.	4
Additional spacing should be considered for ease of installation and servicing. The door opens more than 90°, and it is not reversible.	4
Additional clearances might be required for wall, door, and floor moldings.	4
Additional spacing of 1\	4
Companion appliance spacing should also be considered.	4
Washer Dimensions	4
Drain System	5
Standpipe drain system - wall or floor (views A & B)	5
Laundry tub drain system (view C)	5
Floor drain system (view D)	5
Electrical Requirements	6
A 120 volt, 60 Hz., AC only, 15- or 20-amp, fused electrical supply is required. A time-delay fuse or circuit breaker is recommended. It is recommended that a separate circuit serving only this appliance be provided.	6
This washer is equipped with a power supply cord having a 3 prong grounding plug.	6
To minimize possible shock hazard, the cord must be plugged into a mating, 3 prong, grounding-type outlet, grounded in accordance with local codes and ordinances. If a mating outlet is not available, it is the personal responsibility and obligation o...	6
If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate.	6
Do not ground to a gas pipe.	6
Check with a qualified electrician if you are not sure the washer is properly grounded.	6
Do not have a fuse in the neutral or ground circuit.	6
installation instructions	7
Remove Transport System	7
1. On the back of the washer, loosen the 4 transport bolts using a 13 mm wrench.	7
2. Once the bolt is loose, move it to the center of the hole and completely pull out the bolt, including the plastic spacer covering the bolt.	7
3. Once all 4 bolts are removed, discard the bolts and spacers. Then pull the power cord through the opening of the rear panel and close the hole with the attached cap.	7
4. Cover the bolt holes with the 4 transport bolt hole plugs.	7
Connect the Inlet Hoses	7
1. Attach a hose to the hot water faucet. Screw on coupling by hand until it is seated on the washer.	7
2. Attach a hose to the cold water faucet. Screw on coupling by hand until it is seated on the washer.	7
3. Using pliers, tighten the couplings with an additional two-thirds turn.	7
Run water through both faucets and inlet hoses, into a laundry tub, drainpipe or bucket, to get rid of particles in the water lines that might clog the inlet valve screens.	7
Check the temperature of the water to make sure that the hot water hose is connected to the hot water faucet and that the cold water hose is connected to the cold water faucet.	7
1. Attach the hot water hose to the washer’s hot (H) water inlet valve. Screw on coupling by hand until it is seated on the washer.	8
2. Attach the cold water hose to the washer’s cold (C) water faucet. Screw on coupling by hand until it is seated on the washer.	8
3. Using pliers, tighten the couplings with an additional two-thirds turn.	8
4. Turn on the water faucets completely and check for leaks.	8
Connect the Drain Hose	8
1. Use locking pliers, squeeze hose clamp tabs together and insert over the end of drain hose.	8
2. Slide drain hose onto washer connection.	8
3. Once drain hose is in place, release pliers.	8
4. Washer drain system can be installed using a floor drain, wall standpipe, floor standpipe, or laundry tub.	8
Use the drain hose form, and do not force excess drain hose into standpipe. Hose should be secure, but loose enough to provide a gap for air.	8
Do not lay excess hose on the bottom of the laundry tub.	8
Floor drain	8
Secure the Drain Hose	9
1. Drape the power cord over the washer top.	9
2. Move the washer to its final location.	9
3. Place the drain hose in the laundry tub or standpipe as shown. See illustrations A and B.	9
Do not force excess drain hose back into the rear of the washer.	9
To avoid siphoning, do not seal or put more than 4½\	9
4. If the washer faucets and the drain standpipe are recessed, put the hooked end of the drain hose in the standpipe as shown. See illustration C.	9
Level the Washer	9
1. Slide the washer to its final location.	9
2. Check that all four feet are in firm contact with the floor.	9
3. Check the levelness of the washer by placing a level on the top edge of the washer, first side to side then front to back.	9
4. Make sure all four feet are in firm contact with the floor. Then check that the washer is perfectly level (use a level). Repeat steps 1-3 until washer is level.	9
5. After the washer is level, and all four feet are in firm contact with the floor, use a 9/16\	9
6. The washer should not move front to back, side to side, or diagonally when pushed on its top edges.	9
7. Confirm the levelness of the washer.	9
Complete Installation	9
1. Check the electrical requirements. Be sure that you have the correct electrical supply and the recommended grounding method. See “Electrical Requirements.”	9
2. Check that all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped.	9
3. Check that you have all of your tools.	9
4. Dispose of/recycle all packaging materials.	9
5. Check that both water faucets are on.	9
6. Check for leaks around faucets and inlet hoses.	9
7. Plug into a grounded 3 prong outlet.	9
8. Read “Washer Use.”	9
9. To test and to clean your washer, measure 1/2 the detergent manufacturer’s recommended amount of High Efficiency (HE) detergent for a medium-size load. Pour the detergent into the detergent dispenser. Select Clean Washer with AFFRESH™ cycle, t...	9
Use only HE High Efficiency detergent.	9
FEATURES AND BENEFITS	10
Electronic Controls	10
Auto Water Level	10
Larger Load Size	10
Suspension System	10
2 Springs to isolate vibration	10
3 Shock absorbers at the washer base to minimize movement	10
Stainless Steel Drum	10
Adaptive Variable Speed Motor	10
Add a Garment	10
Dynamic Balance	10
Smart Dispensers	10
Use only HE High Efficiency detergent.	10
washer USE	11
Starting Your Washer	11
Using the Proper Detergent	11
Use only HE High Efficiency detergent.	11
1. To load washer Open the washer door by pulling on the handle. Sort laundry according to color and type of fabric. Place a load of sorted clothes in the washer. Do not overload washer. Overloading can cause poor cleaning.	11
2. Close the washer door by pushing it firmly until the lock clicks. After a lock check at the beginning of the cycle, the washer door will remain locked during the wash cycle.	11
3. Open the dispenser drawer and add laundry products to the detergent, bleach, or fabric softener compartments. Close drawer slowly to avoid spills. See “Using the Dispenser.”	11
4. Turn on the washer by pressing POWER or Select Cycle button. Select one of the cycles by pushing the cycle selector. The indicator light for the selected cycle will illuminate. When selecting a Wash Cycle, the TEMP indicator light for the preset t...	11
5. Select the desired Options. Not all Options are available with all cycles. See “Options.”	11
6. If desired, select the Cycle Signal. The signal is helpful when you are washing items that should be removed from the washer as soon as it stops. Press and hold CYCLE SIGNAL to select signal on or signal off.	11
7. To begin the wash cycle immediately Press and hold START/PAUSE (for approximately 3 seconds).	12
Using the Dispenser	12
Use only HE High Efficiency detergent.	12
1. Pull out the dispenser drawer.	12
2. Add the desired laundry products to the proper compartment.	12
3. Push in the dispenser drawer slowly and completely (to avoid a spill).	12
Dispenser	12
Main Wash detergent compartment	12
Liquid color-safe bleach or oxi products may be added to the Main Wash compartment along with liquid detergent.	12
Powdered color-safe bleach or oxi products may be added to the Main Wash compartment along with the powdered detergent.	12
Do not mix powdered and liquid products in the Main Wash compartment.	12
Use the measurement device which comes with the detergent. Add no more than the manufacturer's recommended amount.	12
Chlorine bleach compartment	12
Use only liquid chlorine bleach in this dispenser. Do not use this dispenser to add powdered chlorine or any form of color- safe bleach or oxi products to your load.	12
Always measure liquid chlorine bleach. Use a measuring cup with a pour spout; do not guess. Follow the manufacturer’s directions for proper use.	12
Do not fill beyond the “MAX” level.	12
Fabric softener compartment	12
Do not fill beyond the “MAX” level.	12
Pausing or Restarting	13
1. To pause the washer at any time, press START/PAUSE.	13
2. To continue the cycle, press and hold START/PAUSE (for approximately 3 seconds).	13
Changing Cycles and Options	13
1. Press POWER.	13
2. The washer powers down, the door unlocks, and clothes can be removed.	13
1. Press START/PAUSE once.	13
2. Press the desired OPTION. If the option is not available, the machine will beep.	13
3. Press and hold START/PAUSE (for approximately 3 seconds) to continue the cycle.	13
1. Press START/PAUSE.	13
2. Select DRAIN & SPIN.	13
3. Press and hold START/PAUSE (for approximately 3 seconds) to begin the drain.	13
4. When the spin is complete, the door unlocks. Items can be removed from the washer.	13
Status Lights	13
1. Press START/PAUSE. The washer door unlocks, and items can be added.	13
2. To continue the cycle, close the door and press and hold START/PAUSE (for approximately 3 seconds).	13
Cycles	13
Each cycle has a preset cycle time, temperature, spin speed, and may have preset Options. The preset settings provide the recommended fabric care for the selected cycle.	13
The preset settings can be changed anytime before START/ PAUSE is pressed. Not all Options (TEMP) are available with all Cycles. To change settings after the cycle has started, press START/PAUSE, then select the desired settings. Press and hold START...	13
Cycle	13
Estimated Time* (hr:min)	13
Temp	13
Spin Speed	13
Use mesh garment bags to wash undergarments such as underwire bras, items with strings, and small items such as socks.	14
Loads that need rinsing only.	14
Adding fabric softener to a load using the fabric softener dispenser.	14
1. Select Drain & Spin cycle.	14
Normal Sounds	14
Options	14
If an option is available with a selected cycle, the light for that option will illuminate when selected.	14
If an option is unavailable with a selected cycle, there will be a short tone and the light for that option will not illuminate when selected.	14
Temperature Guide	14
Controlled Temperature	14
Cold rinse is not controlled by the ATC and will be the same temperature as the water coming from your cold water faucet.	14
Laundry Tips	15
Preparing clothes for washing	15
Use only High Efficiency detergents. The package for this type of detergent will be marked “HE” or “High Efficiency.” This wash system, along with less water, will create too much sudsing with a regular non-HE detergent. Using regular deterge...	15
Use only HE High Efficiency detergent.	15
Close zippers, snaps, and hooks to avoid snagging other items. Remove pins, buckles, and other hard objects to avoid scratching the washer interior. Remove non-washable trim and ornaments.	15
Empty pockets. Small items can be caught with the washer resulting in noise or plugging the pump.	15
Turn down cuffs; brush away lint and dirt.	15
Turn wool and synthetic knits inside out to avoid pilling.	15
Tie strings and sashes so they will not tangle.	15
Mend tears, loose hems, and seams.	15
Treat spots and stains.	15
Stained or wet garments should be washed promptly for best results.	15
Mix large and small items, avoid washing single items, and load evenly.	15
Wash small items, such as infant socks, in a mesh garment bag. To create a balanced load it is recommended that more than one garment bag be used, and that each garment bag be filled with equal amounts of material.	15
Sorting	15
Separate heavily soiled items from lightly soiled ones, even if they would normally be washed together. Separate lint-givers (towels, chenille) from lint-takers (corduroy, synthetics, permanent press). When possible, turn lint-givers inside out.	15
Separate dark colors from light colors, colorfast items from noncolorfast items.	15
Sort by fabric and construction (sturdy cottons, knits, delicate items).	15
Unloading	15
Remove clothes from washer after the cycle is completed. Metal objects such as zippers, snaps, and buckles may rust if left in the washer basket for a long time.	15
When unloading garments, occasionally check under the colored seal at the front of the tub for small items.	15
Loading	15
Loading suggestions	15
Stain Removal Guide	16
Ink	16
4	16
Grass	16
4	16
Blood	16
4	16
Tomato Products	16
4	16
Coffee/ Chocolate	16
4	16
Mud	16
4	16
Cosmetics	16
Dirty Motor Oil	16
Ring around the Collar	16
4	16
Washer care	17
Cleaning Your Washer	17
1. Open the washer door and remove any clothing or items from the washer.	17
2. Inspect the colored seal/bellow between the door opening and the basket for stained areas. Pull back the seal/bellow to inspect all areas under the seal/bellow and to check for foreign objects.	17
3. If stained areas are found, wipe down these areas of the seal/ bellow, using the procedure that follows.	17
a) Mix a dilute solution, using 3/4 cup (177 mL) of liquid chlorine bleach, and 1 gal. (3.8 L) of warm tap water.	17
b) Wipe the seal/bellow area with the dilute solution, using a damp cloth.	17
c) Let stand 5 minutes.	17
d) Wipe down area thoroughly with a dry cloth and let the washer interior air dry with door open.	17
Wear rubber gloves when cleaning for prolonged periods.	17
Refer to the bleach manufacturer’s instructions for proper use.	17
Read these instructions completely before beginning the cleaning process.	17
Begin procedure	17
1. Open the washer door and remove any clothing or items from the washer.	17
2. Using the AFFRESH® washer cleaner (Recommended): Add one AFFRESH® washer cleaner tablet to the washer drum.	17
3. Open the dispenser drawer and immediately add 2/3 cup (160 mL) of liquid chlorine bleach to the bleach compartment.	17
4. Close the washer door and dispenser drawer.	17
5. Select the CLEAN WASHER with AFFRESH™ cycle.	17
6. Press START/PAUSE.	17
7. The cycle will determine whether clothing or other items are in the washer.	17
Repeat steps 1, 2, and 6 to start the cycle again.	17
8. Once the cycle has begun, allow the cycle to complete.	17
9. After the cycle is complete, leave the door open slightly, to allow for better ventilation and drying of washer interior.	17
Always do the following to maintain washer freshness	17
Use only HE High Efficiency detergent.	17
Leave the door slightly open after each cycle to allow for better ventilation and drying of washer interior.	17
Repeat the cleaning procedure monthly.	17
If the procedure does not sufficiently improve the machine freshness, please evaluate your installation and usage conditions for other causes.	17
1. Unlock the dispenser drawer by pressing the Release Lever. See “Using the Dispenser.” Remove the drawer.	17
2. Remove the inserts (the siphon from the softener and bleach compartments).	17
3. Wash the parts under running water.	17
4. Replace the inserts and return the dispenser to the drawer.	17
Water Inlet Hoses	18
Vacation, Storage, and Moving Care	18
Non-use or vacation care:	18
Unplug washer or disconnect power.	18
Turn off the water supply to the washer. This helps avoid accidental flooding (due to a water pressure surge) while you are away.	18
Slightly open door to provide ventilation.	18
1. Put 1 qt (1 L) of R.V.-type antifreeze in the drum.	18
2. Run washer on a Rinse & Spin cycle.	18
3. Unplug washer or disconnect power.	18
4. Shut off both water faucets.	18
5. Disconnect water inlet hoses from faucets and drain.	18
1. Flush water pipes.	18
2. Reconnect water inlet hoses to faucets.	18
3. Turn on both water faucets.	18
4. Plug in washer or reconnect power.	18
5. Run the washer through the Normal cycle with 1/2 the manufacturer’s recommended amount of HE detergent for a medium-size load, to clean the washer and remove the antifreeze, if used.	18
1. If washer will be moved during freezing weather, put in 1 qt (1 L) of R.V.-type antifreeze in the drum. Run washer on a Rinse & Spin cycle.	18
2. Unplug the power cord.	18
3. Disconnect the drain hose from the drain system and attach to rear panel clips.	18
4. Shut off both water faucets.	18
5. Disconnect the water inlet hoses from faucets, then drain the hoses and clip them to the rear panel of the washer.	18
6. IMPORTANT: Call service. Do not reuse transport bolts. Washer must be transported in the upright position. To avoid suspension and structural damage, your machine must be properly set up for relocation by a certified technician.	18
1. Follow the “Installation Instructions” to locate, level, and connect the washer.	18
2. Run the washer through the Normal cycle with 1/2 the manufacturer’s recommended amount of HE detergent for a medium-size load, to clean the washer and remove the antifreeze, if used.	18
troubleshooting	19
First try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions) to possibly avoid the cost of a service call...	19
In U.S.A. http://www.whirlpool.com/help - In Canada www.whirlpool.ca	19
“F8E1” on display (Long Fill - no water or insufficient water supply) Press POWER to cancel the cycle. Unplug washer or disconnect power.	19
“F9E1” on display (Drain Problem) Press POWER to cancel the cycle. Unplug washer or disconnect power.	19
“F--E--” Variables (Washer Problem) Press POWER to cancel the cycle. Select DRAIN & SPIN if there is excessive water in the washer.	19
Is the washer level? The washer must be level. The four feet should be properly installed, and the nuts should be tightened against the washer cabinet.	19
Did you empty pockets? You may be hearing items that are caught under the door seal or basket. Check under the door seal and remove items.	19
Washer making a different noise? As with any new product, you will hear sounds that you are not accustomed to. You may hear various sounds when the door is locked or unlocked, and during the washing, rinsing, or spinning process. Between changes in w...	19
Is washer installed on a sturdy and solid floor? Refer to the “Installation Instructions” for flooring requirements. Noise and vibration may be reduced by placing a piece of 3/4\	19
Is the washer gurgling or humming? As water is drained from the washer, you may hear air being pulled through the pump. This happens during the end of draining. It is normal.	19
Are you washing items with metal snaps, buckles, or zippers? You may hear metal items touching the washer drum. This is normal.	19
Were the 4 shipping bolts in the back of the machine removed? See “Remove Transport System.”	19
Was the door opened during “Add a Garment”? Water can drip off the inside of the door, when the door is opened after the start of a cycle.	19
Is HE detergent being used? The non-High Efficiency detergents can cause oversudsing which can leak from the rear of the washer.	19
Are the fill hoses tight?	19
Are the fill hose gaskets properly seated? Check both ends of each hose. See “Connect the Inlet Hoses.”	19
Is the drain hose properly installed? The drain hose should be secured to the drainpipe or laundry tub. See “Secure the Drain Hose.”	19
Is the sink or drain clogged? Sink and drainpipe must be able to carry away 17 gal. (64 L) of water per minute. If the sink or drain is clogged or slow, water can back up out of drainpipe or sink. Check household plumbing (laundry tubs, faucets, drai...	19
Did you follow the manufacturer’s directions when adding detergent and fabric softener to the dispensers? Measure detergent and fabric softener. Slowly pour into the dispensers. Wipe up all spills. Dilute fabric softener in the fabric softener disp...	20
Did you put powdered or liquid color-safe bleach into the liquid chlorine bleach dispenser (on some models)? Add powdered or liquid color-safe bleach directly to the washer basket. Do not use the chlorine bleach dispenser for color-safe bleach.	20
Is the fabric softener dispenser clogged? Clean the fabric softener dispenser. See “Washer Care” for details.	20
Are the laundry products in the correct dispenser compartment? Add the correct amounts of detergent, fabric softener, or liquid chlorine bleach to the correct compartments. Add powdered or liquid color-safe bleach to the Main Wash compartment.	20
Is there water in the dispenser at the end of the cycle? A small amount of water will remain in the dispenser compartment. This is normal.	20
See “Cleaning Your Washer”	20
Are you using AFFRESH® washer cleaner on a regular basis? AFFRESH® washer cleaner removes and avoids odor-causing residue in all High Efficiency washers. For washers where odor is present, use 3 tablets instead of 1 tablet. After the CLEAN WASHER w...	20
Are you using HE detergent? Use of non-HE detergent can cause a film residue which can result in odor.	20
Did you leave the door open after use? This washer has a tight seal to avoid water leaks. To avoid odors leave the door open to allow the washer to dry between uses.	20
Did all of the water drain out of the washer during the spin? Select DRAIN & SPIN to remove any water remaining in the washer. The washer door will unlock at the end of the drain.	20
Is the door locked and is the “Add a Garment” light on? Press START/PAUSE once. The door will unlock.	20
Is the power cord plugged into a grounded 3 prong outlet? Plug power cord into a grounded 3 prong outlet.	20
Are you using an extension cord? Do not use an extension cord.	20
Has a household fuse blown, or has a circuit breaker tripped? Check that the washer is plugged into a working outlet, and check for blown fuses. Replace the fuse, or reset the circuit breaker. If the problem continues, call an electrician.	20
Is your voltage low? Check electrical source or call electrician.	20
Is the washer door firmly shut? The door must be closed during operation.	20
Has a cycle been selected, but START/PAUSE has not been selected and held for 3 seconds? Press and hold START/PAUSE, for 3 seconds.	20
Was the door open after completion of last cycle? The door must be opened and closed again to start a new cycle.	20
Is the door locked? If door is locked, run a drain cycle and drain the washer.	20
Are the touch pad controls locked? Hold for 3 seconds the button to lock/unlock controls.	20
Are the touch pad buttons not responding? Press POWER on the touch-pad twice. Check the touch-pad/ LED assembly by selecting different cycles and changing the options available to confirm the touch-pad/LED assembly is responding.	20
Does the washer shut down the same time in the same wash cycle repeatedly? Unplug washer or disconnect power. Wait 5 minutes. Plug in washer or reconnect power. Run another cycle.	20
Is the washer level? Check that the washer is level. See “Level Washer.”	21
Has the drawer dispensed detergent? Check that the dispenser drawer is not clogged with detergent.	21
Are both the hot and cold water faucets turned on? Check water hose connections to the washer. Check for plugged screen in water source. Check the water supply and the water valve.	21
Low water pressure at home? Check if the home has low water pressure, open the water faucets.	21
Are both the hot and cold water faucets turned on? Verify hot and cold valve at the water faucets are fully open.	21
Is the water inlet hose kinked? Straighten the hoses. Check water hose connections to the washer and make sure water supply hoses are not obstructed. Check for plugged screen.	21
Are the water inlet valve screens clogged? Turn off the water and remove inlet hoses from the washer. Remove any accumulated film or particles. Reinstall hoses, turn on water, and check for leaks.	21
Are you using HE detergent? HE detergent is a low sudsing detergent. This is normal and will not affect cleaning performance.	21
Low water? This washer uses very little water to provide good cleaning results. You will see little or no water splashing in this washer. This is normal.	21
Is the washer in a normal pause in the cycle? The washer pauses for about 2 minutes during certain cycles. Allow the cycle to continue. Some cycles feature periods of tumbling and soak.	21
Is the washer overloaded? Wash smaller loads.	21
Are the hot and cold water inlet hoses reversed? See “Connect the Inlet Hoses.”	21
Are you washing many loads? As your frequency of loads washed increases, the water temperature may decrease for hot and warm temperatures. This is normal.	21
Low water? This washer uses very little water to provide good cleaning results. You will see little or no water splashing in this washer. This is normal.	21
Are you using HE detergent? HE detergent is a low sudsing detergent. This is normal and will not affect cleaning performance.	21
Is the top of drain hose lower than 30\	21
Does the drain extend into the drain pipe more than 4½\	21
Does the drain hose fit too tightly in the standpipe, or is it taped to the standpipe? The drain hose should be loose yet fit securely. Do not seal the drain hose with tape. The hose needs an air gap. See “Secure the Drain Hose.”	21
Is the drain hose clogged, or the end of the drain hose more than 96\	21
Does the drain hose fit too tightly in the standpipe, or is it taped to the standpipe? The drain hose should be loose yet fit securely. Do not seal the drain hose with tape. The hose needs an air gap. See “Secure the Drain Hose.”	21
Does the drain extend into the drain pipe more than 4½\	21
Excessive suds? When excessive suds are detected, a special suds routine automatically starts. Cycle will complete once extra suds are removed. This will occur more frequently when a non-HE detergent is used.	21
Is the load balanced? A single or bulky item may cause imbalance. Add more items or redistribute the load.	21
Is the drum empty? Rotate drum by hand to check for any binding of the spin basket. Check for clothing stuck between spin basket and outer tub. Move open end drum up and down while holding outer tub steady and check for looseness (more than 1/4\	21
Is the load balanced? A single or bulky item may cause imbalance. Add more items or redistribute the load.	21
Excessive suds? When excessive suds are detected, a special suds routine automatically starts. This routine will add time to the original cycle.	21
Did the load cause imbalance? When an imbalance occurs, an imbalance routine will start to redistribute the load. This extends the cycle.	21
Are you washing a single item or bulky load? Spin time is added if an unbalanced load is detected. The washer will attempt to redistribute the load with additional tumbling.	21
Did you wash a large load in a delicate cycle? When using the Delicate wash cycle you should use small loads. This ensures a gentle wash for your garments without increasing cycle times.	21
Clothes Care	22
Did you use the right cycle for the load being washed? Select a cycle with a higher spin speed.	22
Did you wash a single item or bulky items or have you overloaded the washer? A single item, bulky items, or overloading may cause imbalance. Add items or try to evenly distribute your wet laundry in the drum, and start a Rinse/Drain & Spin cycle. If ...	22
Did you use HE detergent? Suds during rinse and spin cycles can reduce spin speed. Use HE detergent.	22
Did you add detergent to the dispenser? For best results, add detergent to the detergent compartment. Do not add detergent to the washer drum.	22
Did you sort properly? Sort lint givers (towels, chenille) from lint takers (corduroy, synthetics). Transfer of dye can occur when mixing whites and colors in a load. Sort dark clothes from whites and lights.	22
Did you overload the washer? Do not overload the washer. The washer can be fully loaded, but not tightly packed. The wash load must be balanced. Lint can be trapped in the load if overloaded.	22
Check the following: Was paper or tissue left in pockets?	22
Did you use enough HE detergent? Follow manufacturer’s recommendations for the type of load you are washing. For best performance, use only High Efficiency detergent. Use enough HE detergent to remove soil and hold it in suspension.	22
Do you have hard water? Use more detergent for washing heavy soils in cold or hard water.	22
Is your water colder than 60°F (15.6°C)? Wash water colder than 60°F (15.6°C) may not completely dissolve the detergent. Use hot or warm washes if safe for the fabric load. Make sure your hot water system is adequate to provide a hot water wash.	22
Are you using a low speed wash cycle? Powdered detergents may not dissolve well in a slow-speed cycle. For best results, use liquid detergent for slow-speed cycles such as Delicate.	22
Did you unload the washer promptly? To avoid transfer of dye, unload the washer as soon as it stops.	22
Did you use a fabric softener dispensing ball? Dispensing balls will not operate correctly with this washer. Add liquid fabric softener to the fabric softener compartment.	22
Did you use powdered detergent in a low-speed cycle? Consider using liquid detergent.	22
Did you unload the washer promptly? Unload the washer as soon as it stops.	22
Did you use the right cycle for the load being washed? Use the Delicate cycle with a low spin speed to reduce wrinkling.	22
Did you overload the washer? The wash load must be balanced and not overloaded. Loads should tumble freely during washing.	22
Was the wash water warm enough to relax wrinkles? If safe for load, use warm or hot wash water.	22
Are the hot and cold water hoses reversed? Check that the hot and cold water hoses are connected to the right faucets. A hot rinse followed by spin will cause wrinkling. See “Connect the Inlet Hoses.”	22
WHIRLPOOL CORPORATION LAUNDRY WARRANTY	23
For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or furnished with the product, Whirlpool Corporation or Whirlpool Canada LP (hereafter “Whirlpool”) will pay for Fa...	23
2. Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or repair house fuses, or to correct house wiring or plumbing.	23
3. Service calls to repair or replace appliance light bulbs, air filters or water filters. Consumable parts are excluded from warranty coverage.	23
4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in accordance with electrical or plumbing codes, or use of products not approved by Whirlpool.	23
5. Cosmetic damage, including scratches, dents, chips or other damage to the finish of your major appliance, unless such damage results from defects in materials or workmanship and is reported to Whirlpool within 30 days from the date of purchase.	23
6. Pick up and delivery. This major appliance is intended to be repaired in your home.	23
7. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.	23
8. Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an authorized Whirlpool servicer is not available.	23
9. The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance with Whirlpool’s published installation instructions.	23
10. Replacement parts or repair labor on major appliances with original model/serial numbers that have been removed, altered, or cannot be easily determined.	23
IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces do not allow limitations on the du...	23
YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. WHIRLPOOL SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow the exclusion or limitation of incide...	23
If outside the 50 United States and Canada, contact your authorized Whirlpool dealer to determine if another warranty applies.	23
If you think you need repair service, first see the “Troubleshooting” section of the Use & Care Guide. If you are unable to resolve the problem after checking “Troubleshooting,” additional help can be found by checking the “Assistance or Se...	23
SÉCURITÉ DE LA LAVEUSE	24
Exigences d'installation	25
Outillage et pièces	25
Outils nécessaires au raccordement des tuyaux d'arrivée d'eau	25
Pince (ouverture jusqu'à 19/16\	25
Lampe de poche (facultative)	25
Outils nécessaires pour le raccordement du tuyau de vidange	25
Pince multiprise (ouverture jusqu'à 19/16\	25
Outils nécessaires à l'installation	25
Clés plates de 14 mm et 13 mm	25
Niveau	25
Cale en bois	25
Règle ou mètre ruban	25
Autres pièces	25
Options	25
Piédestal facultatif	25
Exigences d'emplacement	25
Un chauffe-eau pour fournir de l'eau à 120°F (49°C) à la laveuse.	25
Une prise électrique reliée à la terre située à moins de 6 pi (1,8 m) de la prise du cordon électrique se trouvant à l'arrière de la laveuse. Voir “Spécifications électriques”.	26
Des robinets d'eau chaude et d'eau froide situés à moins de 4 pi (1,2 m) des robinets d'admission d'eau chaude et d'eau froide, et une pression d'eau de 20-100 lb/po² (137,9-689,6 kPa).	26
Un plancher de niveau ayant une pente maximale de 1\	26
Un plancher robuste et solide capable de soutenir le poids total de la laveuse (eau et charge) de 400 lb (180 kg).	26
Dégagements de séparation à respecter	26
L'emplacement doit être assez grand pour permettre d'ouvrir complètement la porte de la laveuse.	26
Prévoir davantage d'espace pour faciliter l'installation et l'entretien. La porte s'ouvre à plus de 90° et n'est pas réversible.	26
Un espace supplémentaire peut être requis pour les moulures de porte et de plancher et pour les plinthes.	26
Un espace supplémentaire de 1\	26
Il faut aussi prendre en compte l'espace requis entre les appareils voisins.	26
Dimensions de la laveuse	26
Système de vidange	27
Système de vidange avec tuyau de rejet à l'égout - mural ou au plancher (vues A et B)	27
Système de vidange avec évier de buanderie (vue C)	27
Système de vidange au plancher (vue D)	27
Spécifications électriques	28
Une alimentation de 120 volts, 60-Hz, CA seulement, de 15 ou 20 ampères, protégée par un fusible est requise. On recommande d'utiliser un fusible ou un disjoncteur temporisé. Il est recommandé de raccorder l'appareil sur un circuit distinct excl...	28
Cette laveuse comporte un cordon d'alimentation électrique à trois broches pour liaison à la terre.	28
Pour minimiser les risques de choc électrique, on doit brancher le cordon sur une prise de courant de configuration correspondante, à 3 alvéoles, reliée à la terre et installée conformément aux codes et règlements locaux. Si une prise de cour...	28
Si les codes le permettent et si on utilise un conducteur distinct de liaison à la terre, il est recommandé qu'un électricien qualifié vérifie la qualité de la liaison à la terre.	28
Ne pas utiliser une tuyauterie de gaz pour le raccordement à la terre.	28
En cas de doute quant à la qualité de la liaison à la terre de la laveuse, consulter un électricien qualifié.	28
Ne pas installer un fusible dans le conducteur neutre ou le circuit de liaison à la terre.	28
Instructions d'installation	29
Élimination des accessoires de transport	29
1. Au moyen d'une clé de 13 mm, desserrer les 4 boulons de transport situés à l'arrière de la laveuse.	29
2. Une fois le boulon desserré, le déplacer au centre du trou et retirer complètement le boulon, y compris la cale d'espacement en plastique couvrant le boulon.	29
3. Une fois que les 4 boulons ont été retirés, jeter les boulons et les cales d'espacement. Puis tirer le cordon d'alimentation à travers l'ouverture du panneau arrière et obturer le trou avec le bouchon fourni.	29
4. Couvrir les trous des boulons avec les 4 bouchons pour les trous des boulons de transport.	29
Raccordement des tuyaux d'alimentation	29
1. Fixer un tuyau au robinet d'eau chaude. Visser complètement le raccord à la main pour qu'il comprime la rondelle.	29
2. Fixer un tuyau au robinet d'eau froide. Visser complètement le raccord à la main pour qu'il comprime la rondelle.	29
3. À l'aide d'une pince, serrer les raccords en effectuant deux tiers de tour supplémentaires.	29
Laisser s'écouler l'eau des deux robinets et des tuyaux d'alimentation, dans un évier de buanderie, un tuyau rigide de rejet à l'égout ou un seau, pour éliminer les particules se trouvant dans les canalisations d'eau qui pourraient obstruer les ...	29
Vérifier la température de l'eau pour s'assurer que le tuyau d'eau chaude est connecté au robinet d'eau chaude et que le tuyau d'eau froide est connecté au robinet d'eau froide.	29
1. Fixer le tuyau d'eau chaude à la valve du tuyau d'alimentation d'eau chaude (H) de la laveuse. Visser le raccord à la main pour qu'il comprime la rondelle.	30
2. Fixer le tuyau d'eau froide au robinet d'eau froide (C) de la laveuse. Visser le raccord à la main pour qu'il comprime la rondelle.	30
3. À l'aide d'une pince, serrer les raccords en effectuant 2/3 de tour supplémentaires.	30
4. Ouvrir les robinets d'eau complètement et vérifier qu'il n'y a pas de fuites.	30
Raccordement du tuyau de vidange	30
1. À l'aide d'une pince multiprise, serrer les deux onglets de la bride de tuyau et insérer la bride sur l'extrémité du tuyau de vidange.	30
2. Faire glisser le tuyau de vidange sur le raccord de la laveuse.	30
3. Une fois le tuyau de vidange en place, relâcher la prise de la pince.	30
4. Le système de vidange de la laveuse peut être installé à l'aide d'un conduit d'évacuation au plancher, un tuyau rigide de rejet à l'égout mural, un tuyau de rejet à l'égout rigide au plancher ou un évier de buanderie.	30
Utiliser la bride de retenue pour tuyau de vidange et ne pas forcer l'excédent de tuyau rigide dans le tuyau de rejet à l'égout. Le tuyau doit être bien immobilisé, tout en permettant le passage d'air.	30
Ne pas mettre l'excédent du tuyau de vidange dans l'évier de buanderie.	30
Égout au plancher	30
Immobilisation du tuyau de vidange	31
1. Faire passer le cordon d'alimentation par-dessus la laveuse.	31
2. Déplacer la laveuse à son emplacement final.	31
3. Placer le tuyau de vidange dans l'évier de buanderie ou le tuyau rigide de rejet à l'égout. Voir les illustrations A et B.	31
Ne pas forcer l'excédent de tuyau de vidange dans l'arrière de la laveuse.	31
Pour éviter un effet de siphon, ne pas assurer l'étanchéité ou introduire plus de 4½\	31
4. Si les robinets d'eau et le tuyau rigide de rejet à l'égout sont placés en retrait, introduire l'extrémité en crochet du tuyau de vidange dans le tuyau rigide de rejet à l'égout. Voir l'illustration C.	31
Réglage de l'aplomb de la laveuse	31
1. Faire glisser la laveuse à son emplacement final.	31
2. Vérifier que les quatre pieds sont bien en contact avec le plancher.	31
3. Utiliser un niveau placé sur le bord supérieur de la laveuse pour contrôler l'aplomb, d'abord transversalement, puis dans le sens avant arrière.	31
4. S'assurer que les quatre pieds sont bien en contact avec le plancher. Vérifier ensuite que la laveuse est parfaitement d'aplomb (utiliser un niveau). Répéter les étapes 1 à 3 jusqu'à ce que la laveuse soit d'aplomb.	31
5. Après que l'aplomb de la laveuse a été établi et que les quatre pieds sont bien en contact avec le plancher, tourner les écrous de blocage sur les pieds à l'aide d'une clé à molette de 9/16\	31
6. La laveuse ne doit pas bouger d'avant en arrière, latéralement ou transversalement lorsqu'on appuie sur les bords supérieurs.	31
7. Vérifier le bon aplomb de la laveuse.	31
Achever l'installation	31
1. Consulter les spécifications électriques. Vérifier que la tension électrique disponible est correcte et que la méthode recommandée de mise à la terre a été respectée. Voir “Spécifications électriques”.	31
2. Vérifier que toutes les pièces sont maintenant installées. S'il reste une pièce, passer en revue les différentes étapes pour découvrir laquelle aurait été oubliée.	31
3. S'assurer d'avoir récupéré tous vos outils.	31
4. Jeter ou recycler tous les matériaux d'emballage.	31
5. Vérifier que chaque robinet d'arrivée d'eau est ouvert.	31
6. Vérifier qu'il n'y a pas de fuites autour des robinets et des tuyaux d'arrivée d'eau.	31
7. Brancher sur une prise à 3 alvéoles reliée à la terre.	31
8. Lire “Utilisation de la laveuse”.	31
9. Pour tester et nettoyer la laveuse, mesurer la moitié de la quantité de détergent HE Haute efficacité recommandée par le fabricant pour une charge de taille moyenne. Verser le détergent dans le distributeur de détergent. Sélectionner le pr...	31
Utiliser uniquement un détergent HE Haute efficacité.	31
CARACTÉRISTIQUES ET AVANTAGES	32
Commandes électroniques	32
Niveau d'eau automatique	32
Volume de charge plus important	32
Système de suspension	32
2 ressorts pour isoler les vibrations	32
3 amortisseurs à la base de la laveuse pour minimiser le mouvement	32
Tambour en acier inoxydable	32
Moteur adaptatif à vitesse variable	32
Add a Garment (ajouter vêtement)	32
Équilibre dynamique	32
Distributeurs intelligents	32
Utiliser uniquement un détergent HE Haute efficacité.	32
UTILISATION DE LA LAVEUSE	33
Mise en marche de la laveuse	33
Utilisation du détergent approprié	33
Utiliser uniquement un détergent HE Haute efficacité.	33
1. Pour charger la laveuse Ouvrir la porte de la laveuse en tirant sur la poignée. Trier le linge d'après la couleur et le type de tissu. Placer une charge de linge trié dans la laveuse. Ne pas surcharger la laveuse. Une surcharge peut causer un n...	33
2. Fermer la porte de la laveuse en la poussant fermement jusqu'à ce que le verrou s'enclenche. Après un contrôle du verrouillage au début du programme, la porte de la laveuse demeurera verrouillée durant le programme de lavage.	33
3. Ouvrir le tiroir distributeur et verser les produits de lessive dans les compartiments de détergent, d'agent de blanchiment ou d'assouplissant de tissu. Fermer le tiroir lentement pour éviter les renversements. Voir “Utilisation du distributeu...	33
4. Mettre la laveuse en marche en appuyant sur le bouton POWER (mise sous tension) ou Select Cycle (sélectionner un programme). Sélectionner un des programmes en appuyant sur le sélecteur de programme. Le témoin lumineux correspondant au programm...	34
5. Sélectionner les Options désirées. Toutes les Options ne sont pas disponibles avec tous les programmes. Voir “Options”.	34
6. Si désiré, sélectionner le signal de fin de programme. Le signal est utile lorsque vous lavez des articles qui doivent être enlevés de la laveuse aussitôt qu'elle s'arrête. Appuyer sur CYCLE SIGNAL (signal de programme) pour sélectionner s...	34
7. Pour commencer le programme de lavage immédiatement Appuyer sur START/PAUSE (pendant 3 secondes environ).	34
8. Pour commencer le programme de lavage ultérieurement Appuyer sur DELAY START (mise en marche différée) jusqu'à ce que la durée de délai souhaitée (en heures) s'affiche. Appuyer sur START/PAUSE (mise en marche/pause). Le témoin restera allu...	34
Utilisation du distributeur	34
Utiliser uniquement un détergent HE Haute efficacité.	34
1. Tirer le tiroir distributeur.	34

Match case Limit results 1 per page

Programmes

e lavage

Choisir les programmes de lavage en appuyant sur le bouton de

sélection de programme jusqu'au programme désiré. Chaque

programme est conçu pour différents types de tissu et niveaux

de saleté.

■

Chaque programme comporte une durée, température et

vitesse d'essorage préréglées

et peut comporter des options

préréglées. Les préréglages procurent les soins aux tissus

recommandés pour le programme sélectionné.

■

Les préréglages peuvent être modifiés à tout moment avant

que l'on ait appuyé sur START/PAUSE (mise en marche/

pause). Toutes les options (TEMP) ne sont pas disponibles

avec tous les programmes. Pour modifier les réglages après le

début d'un programme, sélectionner START/PAUSE (mise en

marche/pause) puis sélectionner les réglages désirés.

Appuyer sur la touche START/PAUSE (pendant environ

3 secondes) pour poursuivre le programme.

Préréglages

e programme

Chaque programme comporte une durée, température et vitesse

d'essorage préréglées. Ces réglages procurent les soins aux

tissus recommandés pour le programme sélectionné. Voir le

tableau.

*Les durées de programme varient automatiquement en fonction

de la pression et de la température de l'eau, du détergent et de la

charge de linge. La durée du programme sera prolongée en cas

d'excès de mousse ou si la charge est déséquilibrée.

Heavy Duty (service intense)

Utiliser ce programme pour laver des charges de vêtements

robustes, aux couleurs grand teint et très sales. Ce programme

combine un culbutage à vitesse rapide, une durée de lavage

prolongée et un essorage à vitesse élevée pour réduire les durées

de séchage.

Normal

Utiliser ce programme pour laver des charges de tissus qui ne se

repassent pas tels que chemises de sport, chemisiers, vêtements

de travail tout-aller, mélanges à pressage permanent, coton et

linge de maison et tissus synthétiques. Ce programme combine

un culbutage à vitesse moyenne, un essorage à vitesse élevée et

un processus de refroidissement de la charge pour réduire le

froissement.

Delicate (articles

élicats)

Utiliser ce programme pour laver les tissus fragiles et la lingerie.

Ce programme combine un culbutage à basse vitesse et un

essorage à basse vitesse pour assurer un soin délicat des tissus.

■

Utiliser des sacs en filet pour laver les sous-vêtements tels

que les soutiens-gorge à armature, les articles avec cordons

et les articles de petite taille tels que les chaussettes.

Rinse & Spin (rinçage et essorage)

Utiliser ce programme pour obtenir un rinçage et un essorage

seulement. Ce programme combine un culbutage à vitesse élevée

et un essorage à vitesse élevée.

Le programme Rinse & Spin est utile pour :

■

Les charges qui nécessitent un rinçage uniquement.

■

Ajouter de l'assouplissant de tissu à une charge en utilisant le

distributeur d'assouplissant de tissu.

Drain & Spin (vi

ange et essorage)

Utiliser ce programme pour vidanger la laveuse ou pour vidanger

et essorer la charge de lavage. La vitesse d'essorage est

préréglée à élevée.

Utilisation

e Drain & Spin (vi

ange et essorage) :

Sélectionner le programme Drain & Spin (vidange et

essorage).

Programme

Durée

estimée*

(hr:min)

Temp.

Vitesse

'essorage

Heavy Duty (service

intense)

1:22

Hot

(chaude)

High

(élevée)

Normal

1:12

Warm

(tiède)

High

(élevée)

Delicate

(articles

élicats)

0:37

Cold

(froide)

Low

(basse)

Rinse & Spin

(rinçage et

essorage)

0:26

Cold

(froide)

High

(élevée)

Drain & Spin

(vi

ange et

essorage)

0:14

N/A

High

(élevée)

Clean Washer with

AFFRESH™

(nettoyage

e la

laveuse avec

AFFRESH™)

0:54

N/A

High

(élevée)