Whirlpool WFW9290FBD Use & Care Guide - Page 17

Select CYCLE, Adjust settings, if desired, Select any additional options, Setting a delayed wash

Get Whirlpool WFW9290FBD PDF manuals and user guides View all Whirlpool WFW9290FBD manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

8. Select CYCLE* 10. Select any additional options* Turn cycle knob to select your wash cycle. See "Cycle Guide" for details on cycle features. 9. Adjust settings, if desired* To add an option to the cycle, touch its name - Steam Clean, EcoBoost™, FanFresh®, Extra Rinse, Cycle Signal, or Control Lock. To remove an option from the selected cycle, touch the option again. 11. Setting a delayed wash The display will show the default settings for the selected cycle. To adjust a setting, touch its name - Wash Temp, Spin, Soil, or PreSoak. Adjusting settings will change the Estimated Time Remaining. Tightly packing the load, unbalanced loads, or excessive suds may also cause the washer to increase the cycle time. You can also adjust the detergent concentration and water hardness settings, if needed. Default settings are 2x detergent concentration and normal water hardness. If the detergent concentration is not listed on the package, see "About Detergent Concentration" to calculate the concentration. To Adjust Dispenser Settings: 1. Touch DETERGENT CONCENTRATION until the desired concentration appears on the time display. 2. Touch WATER HARDNESS until the desired water hardness appears on the time display. If you do not want to begin a cycle immediately, you may choose the Delay Wash option. This will delay the start of the wash cycle by up to 8 to 12 hours depending on your model. To set a Delayed Start: 1. Touch ADJUST DELAY TIME + or - to set the desired delay time. 2. Touch START to start the delay countdown. The countdown stops blinking. *Not all options and settings are available with all cycles. See "Cycle Guide" for available options and settings. 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
17
8.
Select CYCLE*
Turn cycle knob to select your wash cycle. See “Cycle Guide”
for details on cycle features.
The display will show the default settings for the selected
cycle. To adjust a setting, touch its name – Wash Temp, Spin,
Soil, or PreSoak. Adjusting settings will change the Estimated
Time Remaining. Tightly packing the load, unbalanced loads,
or excessive suds may also cause the washer to increase the
cycle time.
You can also adjust the detergent concentration and water
hardness settings, if needed. Default settings are 2x detergent
concentration and normal water hardness. If the detergent
concentration is not listed on the package, see “About
Detergent Concentration” to calculate the concentration.
To Adjust Dispenser Settings:
1.
Touch DETERGENT CONCENTRATION until the desired
concentration appears on the time display.
2.
Touch WATER HARDNESS until the desired water
hardness appears on the time display.
9.
Adjust settings, if desired*
10.
Select any additional options*
To add an option to the cycle, touch its name – Steam Clean,
EcoBoost
™
, FanFresh
®
, Extra Rinse, Cycle Signal, or Control
Lock. To remove an option from the selected cycle, touch the
option again.
11.
Setting a delayed wash
If you do not want to begin a cycle immediately, you may
choose the Delay Wash option. This will delay the start
of the wash cycle by up to 8 to 12 hours depending on
your model.
To set a Delayed Start:
1.
Touch ADJUST DELAY TIME + or – to set the desired
delay time.
2.
Touch START to start the delay countdown. The countdown
stops blinking.
*Not all options and settings are available with all cycles.
See “Cycle Guide” for available options and settings.