Whirlpool WFW94HEXW Dimension Guide - Page 1

Whirlpool WFW94HEXW Manual

Get Whirlpool WFW94HEXW PDF manuals and user guides View all Whirlpool WFW94HEXW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 1 highlights

Front-Loading Automatic Washer PRODUCT MODEL NUMBERS WFW94HEX, WFW95HEX, WFW97HEX OVERALL DIMENSIONS Washer dimensions 51" (1295 mm) 27" (686 mm) Custom under counter installation: Electrical: A 120 volt, 60 Hz., AC only, 15- or 20-amp, fused electrical supply is required. A time-delay fuse or circuit breaker is recommended. It is recommended that a separate circuit serving only this appliance be provided. Drain System Options Drain system can be installed using a floor drain, wall standpipe, floor standpipe, or laundry tub. Select method you need. IMPORTANT: To avoid siphoning, 4.5" (113 mm) of drain hose should be inside standpipe or below the top of wash tub. Always secure drain hose with beaded tie strap. Floor standpipe drain system 38" (965 mm) 311/2" (800 mm) 1" (25 mm) Recessed area or closet installation (washer only): 39" min. (990 mm) 1" (25 mm) 34" min. (864 mm) 3" (76 mm) 48 in.2 (310 cm2) 41/2" (113 mm) Minimum diameter for a standpipe drain: 2" (51 mm). Minimum carry-away capacity: 17 gal. (64 L) per minute. A 1/4" (6 mm) diameter to 1" (25 mm) diameter Standpipe Adapter Kit is available (Part Number 280130). To order, please see toll-free phone numbers on front page of your Washer User Instructions. Top of standpipe must be at least 30" (762 mm) high; install no higher than 96" (2.44 m) from bottom of washer. If you must install higher than 96" (2.44 m), you will need a sump pump system. Wall standpipe drain system 41/2" (113 mm) 4" (102 mm) 3" (76 mm) 24 in.2 (155 cm2) 1" (25 mm) 1" (25 mm) Recessed area or closet installation (stacked washer and dryer): 6" (152 mm) 3" (76 mm) 771/2" (1969 mm) 48 in.2 (310 cm2) Custom cabinet installation: 7" (178 mm) 14" (356 mm) Floor drain system 5" (127 mm) 3" (76 mm) 24 in.2 (155 cm2) 1" (25 mm) 1" (25 mm) 4" (102 mm) 1" (25 mm) 1" (25 mm) Floor drain system requires a Siphon Break Kit (Part Number 285834) and additional drain hose (Part Number 8318155) with a connector kit (Part Number 285835) that may be purchased separately. To order, please see tollfree phone numbers in your Washer User Instructions. Minimum siphon break: 28" (711 mm) from bottom of washer. (Additional hoses might be needed.) Laundry tub drain system 41/2" (113 mm) min. 30" (762 mm) Minimum capacity: 20 gal. (76 L). Top of laundry tub must be at least 30" (762 mm) above floor; install no higher than 96" (2.44 m) from bottom of washer. Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice. Dimensions are for planning purposes only. For complete details, see Installation Instructions packed with product. Specifications subject to change without notice. Ref. W10254447 08/2010

  • 1
Front-Loading Automatic Washer
PRODUCT MODEL NUMBERS
OVERALL DIMENSIONS
WFW94HEX, WFW95HEX,
WFW97HEX
Electrical:
A 120 volt, 60 Hz., AC only, 15- or 20-amp,
fused electrical supply is required. A time-delay fuse
or circuit breaker is recommended. It is recommended
that a separate circuit serving only this appliance
be provided.
Washer dimensions
Because Whirlpool Corporation policy includes a continuous commitment to improve
Dimensions are for planning purposes only. For complete details, see Installation
our products, we reserve the right to change materials and specifications without notice.
Instructions packed with product. Specifications subject to change without notice.
Ref. W10254447
08/2010
Drain System Options
31
1
/
2
"
(800 mm)
27"
(686 mm)
38"
(965 mm)
51"
(1295 mm)
7"
(178 mm)
14"
(356 mm)
1"
(25 mm)
4"
(102 mm)
1"
(25 mm)
34" min.
(864 mm)
1"
(25 mm)
4"
(102 mm)
24 in.
2
(155 cm
2
)
48 in.
2
(310 cm
2
)
3"
(76 mm)
3"
(76 mm)
1"
(25 mm)
1"
(25 mm)
1"
(25 mm)
39" min.
(990 mm)
1"
(25 mm)
5"
(127 mm)
24 in.
2
(155 cm
2
)
48 in.
2
(310 cm
2
)
3"
(76 mm)
3"
(76 mm)
77
1
/
2
"
(1969 mm)
6"
(152 mm)
1"
(25 mm)
Custom cabinet installation:
Recessed area or closet installation (washer only):
Recessed area or closet installation
(stacked washer and dryer):
Custom under counter installation:
Floor standpipe drain system
4
1
/
2
"
(113 mm)
Wall standpipe drain system
4
1
/
2
"
(113 mm)
Laundry tub drain system
Minimum capacity: 20 gal. (76 L).
Top of laundry tub must be at least
30" (762 mm) above floor; install no
higher than 96" (2.44 m) from bottom
of washer.
30"
(762 mm)
min.
4
1
/
2
"
(113 mm)
Floor drain system requires a Siphon Break Kit (Part
Number 285834) and additional drain hose (Part Number
8318155) with a connector kit (Part Number 285835) that
may be purchased separately. To order, please see toll-
free phone numbers in your Washer User Instructions.
Minimum siphon break: 28" (711 mm) from bottom of
washer. (Additional hoses might be needed.)
Floor drain system
Drain system can be installed using a floor drain, wall
standpipe,
floor standpipe, or laundry tub. Select
method you need.
IMPORTANT:
To avoid siphoning, 4.5" (113 mm) of
drain hose should be inside standpipe or below the top
of wash tub. Always secure drain hose with beaded tie
strap.
Minimum diameter for a standpipe drain: 2" (51 mm).
Minimum carry-away capacity: 17 gal. (64 L) per minute.
A
1
/
4
" (6 mm) diameter to 1" (25 mm) diameter Standpipe
Adapter Kit is available (Part Number 280130). To order,
please see
toll-free phone numbers on front page of your
Washer User Instructions. Top of standpipe must be at
least 30" (762 mm) high; install no higher than 96" (2.44 m)
from bottom of washer. If you must install higher than 96"
(2.44 m), you will need a sump pump system.