Whirlpool WFW96HEAC Use & Care Guide - Page 16

Winter Storage Care, Non-use And Vacation Care, Transporting Your Washer, Washer Care Cont.

Get Whirlpool WFW96HEAC PDF manuals and user guides View all Whirlpool WFW96HEAC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

WASHER CARE (cont.) Cleaning the Precision Dispense Cartridge It is recommended that you rinse out the Precision Dispense cartridge when changing detergent types or concentrations, or when the washer will not be used for an extended period. 1. Pull dispenser out until it stops. 2. Lift out the Precision Dispense cartridge. 3. Lift cover on cartridge and flush interior thoroughly with warm water. 4. Allow to air dry or wipe with a clean, soft towel. IMPORTANT: Cartridge is not dishwasher safe. NON-USE AND VACATION CARE Operate your washer only when you are home. If moving, or not using your washer for a period of time, follow these steps: 1. Unplug or disconnect power to washer. 2. Turn off water supply to washer to avoid flooding due to water pressure surges. 3. Clean the dispensers. See "Cleaning the Dispensers." WINTER STORAGE CARE IMPORTANT: To avoid damage, install and store washer where it will not freeze. Because some water may stay in hoses, freezing can damage washer. If storing or moving during freezing weather, winterize your washer. To winterize washer: 1. Shut off both water faucets, disconnect and drain water inlet hoses. 2. Put 1 qt. (1 L) of R.V.-type antifreeze in washer drum and run washer on NORMAL cycle for about 2 minutes to mix antifreeze and remaining water. 3. Unplug washer or disconnect power. TRANSPORTING YOUR WASHER 1. Shut off both water faucets. Disconnect and drain water inlet hoses. 2. If washer will be moved during freezing weather, follow WINTER STORAGE CARE directions before moving. 3. Disconnect drain hose from drain system and from back of washer. 4. Unplug power cord. 5. Place inlet hoses and drain hose inside washer drum. 6. Bundle power cord with a rubber band or cable tie to keep it from hanging onto the ground. IMPORTANT: Call for service to install new transport bolts. Do not reuse transport bolts. Washer must be transported in the upright position. To avoid structural damage to your washer, it must be properly set up for relocation by a certified technician. 16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
16
Operate your washer only when you are home. If moving,
or not using your washer for a period of time, follow these
steps:
1.
Unplug or disconnect power to washer.
2.
Turn off water supply to washer to avoid flooding due
to water pressure surges.
3.
Clean the dispensers. See “Cleaning the Dispensers.”
WINTER STORAGE CARE
IMPORTANT:
To avoid damage, install and store washer
where it will not freeze. Because some water may stay in
hoses, freezing can damage washer. If storing or moving
during freezing weather, winterize your washer.
To winterize washer:
1.
Shut off both water faucets, disconnect and drain water
inlet hoses.
2.
Put 1 qt. (1 L) of R.V.-type antifreeze in washer drum and
run washer on NORMAL cycle for about 2 minutes to
mix antifreeze and remaining water.
3.
Unplug washer or disconnect power.
NON-USE AND VACATION CARE
TRANSPORTING YOUR WASHER
1.
Shut off both water faucets. Disconnect and drain water
inlet hoses.
2.
If washer will be moved during freezing weather, follow
WINTER STORAGE CARE directions before moving.
3.
Disconnect drain hose from drain system and from back
of washer.
4.
Unplug power cord.
5.
Place inlet hoses and drain hose inside washer drum.
6.
Bundle power cord with a rubber band or cable tie to
keep it from hanging onto the ground.
IMPORTANT:
Call for service to install new transport bolts.
Do not reuse transport bolts. Washer must be transported
in the upright position. To avoid structural damage to
your washer, it must be properly set up for relocation
by a certified technician.
WASHER CARE (cont.)
Cleaning the Precision Dispense Cartridge
It is recommended that you rinse out the Precision
Dispense cartridge when changing detergent types
or concentrations, or when the washer will not be used
for an extended period.
1.
Pull dispenser out until it stops.
2.
Lift out the Precision Dispense cartridge.
3.
Lift cover on cartridge and flush interior thoroughly with
warm water.
4.
Allow to air dry or wipe with a clean, soft towel.
IMPORTANT:
Cartridge is not dishwasher safe.