Whirlpool WGD6400SB Use and Care Manual - Page 13

Read Dryer Use.

Get Whirlpool WGD6400SB PDF manuals and user guides View all Whirlpool WGD6400SB manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

4. Install the 2 hinges to the front panel of the dryer using 4 screws. Use the non-slotted side to attach the hinge to the front panel. 5. Install screws in the top hinge holes in the door. Do not tighten screws. Leave approximately 1A" (5 mm) of screw exposed. f. Check that all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped. 2. Check that you have all of your tools. 3. Dispose of/recycle all packaging materials. 4. Check the dryer's final location. Be sure the vent is not crushed or kinked. 5. Check that the dryer is level. See "Level Dryer." A. Install these screws first. 6. Hang door by placing screw heads into top slotted holes of hinges and slide door down. Align bottom screw holes in hinge and door. Install two bottom screws. Tighten all hinge screws. ] 7. Close door to engage door strike. Electrica( Shock Hazard P(ug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord, Failure to follow these instructions can result in death, fire, or electrical shock. 6. Plug into a grounded 3 prong outlet. Turn on power. 7. Remove any protective film or tape remaining on the dryer. NOTE: Glass door models have a protective film on the window that should be removed. 8. Read "Dryer Use." g. Wipe the dryer drum interior thoroughly with a damp cloth to remove any dust. 10. Test dryer operation by selecting a Timed Dry heated cycle and starting the dryer. For this test, do not select the Air Only modifier. If the dryer will not start, check the following: • Dryer is plugged into a grounded 3 prong outlet. • Electrical supply is connected. • Household fuse is intact and tight, or circuit breaker has not tripped. • Dryer door is closed. 11. When the dryer has been running for 5 minutes, open the dryer door and feel for heat. If you feel heat, cancel cycle and close door. If you do not feel heat, turn off the dryer and check that the gas supply line shutoff valve is open. • If the gas supply line shutoff valve is closed, open it, then repeat the 5-minute test as outlined above. • If the gas supply line shutoff valve is open, contact a qualified technician. 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
4.
Install the 2 hinges to the front panel of the dryer using
4 screws.
Use the non-slotted
side to attach
the hinge to the
front panel.
5.
Install screws
in the top hinge holes in the door. Do not
tighten
screws.
Leave approximately
1A" (5 mm) of screw
exposed.
6.
A. Install these screws
first.
Hang door by placing screw
heads into top slotted
holes of
hinges and slide door down. Align bottom
screw
holes in
hinge and door. Install two bottom
screws.
Tighten all hinge
screws.
]
7.
Close door to engage
door strike.
f.
Check that all parts are now installed.
If there is an extra part,
go back through
the steps to see which step was skipped.
2.
Check that you have all of your tools.
3.
Dispose
of/recycle
all packaging
materials.
4.
Check the dryer's final location.
Be sure the vent is not
crushed
or kinked.
5.
Check that the dryer
is level. See "Level
Dryer."
6.
7.
8.
g.
10.
11.
Electrica(
Shock
Hazard
P(ug into
a grounded
3
prong
outlet.
Do not remove
ground
prong.
Do not use an adapter.
Do not use an extension
cord,
Failure
to follow
these
instructions
can result
in
death,
fire, or
electrical
shock.
Plug into a grounded
3 prong outlet. Turn on power.
Remove
any protective
film or tape remaining
on the dryer.
NOTE: Glass door models
have a protective
film on the
window
that should be removed.
Read "Dryer Use."
Wipe the dryer drum
interior thoroughly
with a damp cloth to
remove any dust.
Test dryer operation
by selecting
a Timed
Dry heated
cycle
and starting
the dryer. For this test, do not select the Air Only
modifier.
If the dryer
will
not start,
check
the
following:
•
Dryer is plugged
into a grounded
3 prong outlet.
•
Electrical
supply
is connected.
•
Household
fuse is intact and tight, or circuit
breaker
has
not tripped.
•
Dryer door
is closed.
When the dryer has been running for 5 minutes, open the
dryer door and feel for heat. If you feel heat, cancel cycle and
close door. If you do not feel heat, turn off the dryer
and
check that the gas supply
line shutoff
valve is open.
•
If the gas supply
line shutoff
valve is closed, open it, then
repeat the 5-minute
test as outlined
above.
•
If the gas supply
line shutoff
valve is open, contact
a
qualified
technician.
13