Whirlpool WVW51UC0F Dimension Guide - Page 1
Whirlpool WVW51UC0F Manual
View all Whirlpool WVW51UC0F manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
30" (76.2 cm) and 36" (91.4 cm) Wall-Mount Canopy Range Hood PRODUCT MODEL NUMBERS WVW51UC0F WVW51UC6F ELECTRICAL REQUIREMENTS A 120-volt, 60-Hz., AC-only, 15-amp, fused electrical circuit is required. CABINET DIMENSIONS PRODUCT DIMENSIONS 10⁷⁄₈" (27.6 cm) 13 33.5 cm) 10" (25.4 cm) min. 13" (33.0 cm) max. 2" (5.1 cm) min. 9" (22.9 cm) min.* 9¹⁄₂" (24.1 cm) 10" (25.4 cm) min. 13" (33.0 cm) max. Vent and power supply cable entry location Side cabinet 20" (50.8 cm)* min. 30" (76.2 cm) or 36" (91.4 cm) Side cabinet "X" bottom of canopy to cooking surface Centerline Cooking surface 20" (50.8 cm) 30" (76.2 cm) or 36" (91.4 cm) **27¹⁄₈" (68.9 cm) min. **41¹⁄₈" (104.5 cm) max. *27¹⁄₈" (68.9 cm) min. *45¹⁄₂" (115.6 cm) max. * For non-vented (recirculating) installations IMPORTANT: Minimum distance "X": 24" (61 cm) from electric cooking surface Minimum distance "X": 27" (68.6 cm) from gas cooking surface Suggested maximum distance "X": 36" (91.4 cm) The chimneys can be adjusted for different ceiling heights. See the following chart. Vented Installations Min. ceiling height Electric cooking surface 7' 4" (2.23 m) Gas cooking surface 7' 7" (2.31 m) Max. ceiling height 9' 5" (2.87 m) 9' 5" (2.87 m) 17 43.7 cm) * For non-vented (recirculating) installations ** For vented installations. VENTING REQUIREMENTS ■■ Vent system must terminate to the outdoors except for non-vented (recirculating) installations. Non-Vented (Recirculating) Installations ■■ Do not terminate the vent system in an attic or other enclosed area. Electric cooking surface Gas cooking surface Min. ceiling height 7' 4" (2.23 m) 7' 7" (2.31 m) Max. ceiling height 9' 9" (2.97 m) 9' 9" (2.97 m) NOTE: The range hood chimneys are adjustable and designed to meet varying ceiling or soffit heights depending on the distance "X" between the bottom of the range hood and the cooking surface. For higher ceilings, a Stainless Steel Chimney Extension Kit Part Number EXTKIT10FS is available from your dealer or an authorized parts distributor. The chimney extension replaces the upper chimney shipped with the range hood. ■■ Do not use 4" (10.2 cm) laundry-type wall cap. ■■ Use metal vent only. Rigid metal vent is recommended. Plastic or metal foil vent is not recommended. ■■ The length of vent system and number of elbows should be kept to a minimum to provide efficient performance. For the Most Efficient and Quiet Operation: ■■ Use no more than three 90° elbows. ■■ Make sure there is a minimum of 24" (61 cm) of straight vent between the elbows if more than 1 elbow is used. ■■ Do not install 2 elbows together. ■■ Use clamps to seal all joints in the vent system. ■■ The vent system must have a damper. If the roof or wall cap has a damper, do not use the damper supplied with the range hood. ■■ Use caulking to seal exterior wall or roof opening around the cap. Because Whirlpool Corporation includes a continues commitment to improve our products, we reserve the right to change materials and specifications without notice. ■■ The size of the vent should be uniform. Dimensions are for planning purposes only. For complete details, see Installation Instructions packed with product. Specifications subject to change without notice. Page 1 of 2 Ref. W10836369A 05/09/2016