Xerox 6200DX Network Guide - Page 35

Macintosh EtherTalk Network (MacOS 8.x/9.x/X, version 10.1), Requirements, Enabling EtherTalk

Get Xerox 6200DX - Phaser Color Laser Printer PDF manuals and user guides
UPC - 095205062090
View all Xerox 6200DX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

Phaser® 6200 Color Laser Printer Macintosh EtherTalk Network (MacOS 8.x/9.x/X, version 10.1) This section provides installation and troubleshooting steps for Macintosh (MacOS 8 through X, version 10.1):  Quick install steps for MacOS 8.x and 9.x - see page 31.  Quick install steps for MacOS X, version 10.1 - see page 33.  Setting up the Macintosh Ethernet port for TCP/IP or AppleTalk - see page 33.  Macintosh troubleshooting step-by-step - see page 34. Requirements  A workstation with the appropriate driver installed.  A working knowledge of the operating system (System 8.0+ or higher) being used on your workstation.  Proper cabling in use to connect your printer to the network. Enabling EtherTalk If you use EtherTalk, Macintosh computers do not require IP addresses. 1. Open the AppleTalk Control Panel. 2. Verify that the Ethernet port is the selected network port. 3. To install the printer driver, double-click the installer on the Printer Installer and Utilities CD-ROM. Perform the next two steps for MacOS 8.x and 9.x. 1. Open the Chooser, select the LaserWriter driver. 2. From the right column of the Chooser, select the printer. Click Create to create the desktop printer. Perform the next two steps for MacOS X, version 10.1 only. 1. Open Print Center. 2. Click Add Printer, select the printer, then click Add. For more details, refer to the infoSMART Knowledge Base at www.xerox.com/officeprinting/infoSMART, Document #2562. Copyright © 2002 Xerox Corporation. All Rights Reserved. 30

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
Phaser® 6200 Color Laser Printer
Copyright © 2002 Xerox Corporation. All Rights Reserved.
30
Macintosh EtherTalk Network
(MacOS 8.x/9.x/X, version 10.1)
This section provides installation and troubleshooting steps for Macintosh (MacOS 8 through X,
version 10.1):
Quick install steps for MacOS 8.x and 9.x — see page 31.
Quick install steps for MacOS X, version 10.1 — see page 33.
Setting up the Macintosh Ethernet port for TCP/IP or AppleTalk — see page 33.
Macintosh troubleshooting step-by-step — see page 34.
Requirements
A workstation with the appropriate driver installed.
A working knowledge of the operating system (System 8.0+ or higher) being used on your
workstation.
Proper cabling in use to connect your printer to the network.
Enabling EtherTalk
If you use EtherTalk, Macintosh computers do not require IP addresses.
1.
Open the
AppleTalk
Control Panel.
2.
Verify that the
Ethernet
port is the selected network port.
3.
To install the printer driver, double-click the installer on the
Printer Installer and Utilities
CD-ROM
.
Perform the next two steps for MacOS 8.x and 9.x.
1.
Open the
Chooser
, select the
LaserWriter
driver.
2.
From the right column of the
Chooser
, select the printer. Click
Create
to create the desktop
printer.
Perform the next two steps for MacOS X, version 10.1 only.
1.
Open
Print Center
.
2.
Click
Add Printer
, select the printer, then click
Add
.
For more details, refer to the infoSMART Knowledge Base at
www.xerox.com/officeprinting/infoSMART
, Document #2562.