Xerox 850DP Xerox Wide Format 8825/8830/8850/8855/X2 Tech System Introduction - Page 50

/8830/8850 Printer Control Panel Displayed Error Codes

Get Xerox 850DP - Phaser Color Solid Ink Printer PDF manuals and user guides
UPC - 042215454858
View all Xerox 850DP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

XES Synergix 8825/8830/8850/8855 & X2-TECH System Introduction 42 8825/8830/8850 Printer Control Panel Displayed Error Codes Status Code C0.-C1.-C2.-C3.-C4.-E2.-E4.-- E5.-- E6.-E7.-E9.-F1.-J1.01 J2.02 LL.-U1.01 Explanation This code indicates a cutter problem. Follow the instructions on the Message Display. This code indicates a problem with Roll 1. Follow the instructions on the Message Display. This Code indicates a problem with Roll 2. Follow the instructions on the Message Display. This code indicates a problem with Roll 3. Follow the instructions on the Message Display. This code indicates a problem at the cut sheet bypass. Follow the instructions on the Message Display. This code indicates a problem in the paper path. Follow the instructions on the Message Display. This code indicates a problem in the fuser area. (Trail or lead edge jam. Stripper finger sensor jam. Copy exit sensor, activate bypass sensor, or accordian jam sensor was detected to be actuated when the machine was powered-up.) Follow the instructions on the Message Display. This code indicates an interlock problem. (Developer cover, cutter cover, cut sheet shelf, or front door was opened while machine was in run mode.) Follow the instructions on the Message Display. This code indicates a problem in the paper path. Follow the instructions on the Message Display. Communication failure with the controller. Switch the printer off. Wait a few seconds, then switch the printer on. Switch the printer off. Wait a few seconds, then switch the printer on. This code indicates a problem in communicating with the folder. Follow the instructions on the Folder Message Display. This code indicates that the toner cartridge is out of toner and should be replaced. Refer to the CARE section, "Replacing the Toner Cartridge," in the Xerox 8825/8830 Printer Operator Manual. This code indicates that the toner cartridge is not installed correctly. Refer to the CARE section, "Replacing the Toner Cartridge," in the Xerox 8825/8830 Printer Operator Manual. Communications, sensor, or fuser errors. Switch the printer off. Wait a few seconds, then switch the printer on. Copy counter disconnected. Call for service.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
XES Synergix 8825/8830/8850/8855 & X2-TECH System Introduction
42
8825/8830/8850 Printer Control
Panel Displayed Error Codes
Status Code
Explanation
C0.--
This code indicates a cutter problem.
Follow the instructions on the Message Display.
C1.--
This code indicates a problem with Roll 1.
Follow the instructions on the Message Display.
C2.--
This Code indicates a problem with Roll 2.
Follow the instructions on the Message Display.
C3.--
This code indicates a problem with Roll 3.
Follow the instructions on the Message Display.
C4.--
This code indicates a problem at the cut sheet bypass.
Follow the instructions on the Message Display.
E2.--
This code indicates a problem in the paper path. Follow the instructions on the Message Display.
E4.--
This code indicates a problem in the fuser area. (Trail or lead edge jam.
Stripper finger sensor jam.
Copy exit sensor, activate bypass sensor, or
accordian jam sensor was detected to be actuated when the machine was powered-up.)
Follow the instructions on the Message Display.
E5.--
This code indicates an interlock problem. (Developer cover, cutter cover, cut sheet shelf, or front door was opened while machine was in run mode.)
Follow the instructions on the Message Display.
E6.--
This code indicates a problem in the paper path. Follow the instructions on the Message Display.
E7.--
Communication failure with the controller. Switch the printer off.
Wait a few seconds, then switch the printer on.
E9.--
Switch the printer off.
Wait a few seconds, then switch the printer on.
F1.--
This code indicates a problem in communicating with the folder. Follow the instructions on the Folder Message Display.
J1.01
This code indicates that the toner cartridge is out of toner and should be replaced.
Refer to the CARE section, “Replacing the Toner Cartridge,” in the
Xerox 8825/8830 Printer Operator Manual.
J2.02
This code indicates that the toner cartridge is not installed correctly.
Refer to the CARE section, “Replacing the Toner Cartridge,” in the Xerox 8825/8830
Printer Operator Manual.
LL.--
Communications, sensor, or fuser errors.
Switch the printer off.
Wait a few seconds, then switch the printer on.
U1.01
Copy counter disconnected.
Call for service.