Yamaha 01X Installation Guide - Page 12
set to ASIO operation. The two latter ASIO - mlan drivers
View all Yamaha 01X manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 12 highlights
e Mode This determines the particular driver operation, and should be set to match the particular software used. • ASIO All mLAN audio channels are set for ASIO. The two latter channels are connected to the monitor input of the 01X. • WDM(2CH)+ASIO...... This setting is intended for certain sequencers, such as the SQ01. In this setting, mLAN audio channels 15 and 16 (7and 8 when 01X is set to 96kHz/88.2kHz operation) (from computer to 01X) are set to WDM (for TWE), while the remaining channels (also computer to 01X) are set to ASIO (for the Audio Mixer). All mLAN audio channels from the 01X to computer are set to ASIO operation. The two latter ASIO channels are connected to the monitor input of the 01X. • WDM This setting is intended for certain sequencers, such as SONAR, and sets all mLAN audio channels to WDM operation. The two latter channels are connected to the monitor input of the 01X. • When selecting "WDM + ASIO" or "WDM," confirm the settings in the Sounds and Audio Devices Properties (page 13) after installing r Status This indicates the current data (MIDI/Audio) reception status (from 01X to Computer) of the mLAN connection. If there is an error in transmission, a message is shown. Blue .........Data is being properly transmitted. Yellow......Only one type of data (MIDI or audio) is being received. Red ..........Error in reception. Gray.........No reception. About the Information window This window indicates the data reception status (from the 01X to computer) for both MIDI and audio. R1, R2, etc. This indicates the data reception status. "R1" corresponds to MIDI reception while "R2 corresponds to audio reception from the 01X. The number of tabs shown differs depending on your particular computer configuration. Receive Status This mark indicates the order in which the data of each format is received. The symbol "o" indicates that data in the corresponding format is being received. The symbol "-" indicates that data in a different format is being received. For example, the symbol "oooooooo-" in the "Audio" field indicates that nine sequences have been received, and the first eight sequences are in the audio data format. The "Unknown" field displays symbols if sequences in unknown formats are received. These fields are blank if no mLAN data is received. If an error occurs during reception, a red warning message flashes. In this case, check the transmission device. Icon Blue .........Reception is normal. Red..........Error in reception. Gray ........No reception. t Set Clicking this button actually applies the settings made in this window. Changes to the settings do not take effect unless [Set] is clicked. y Revert If you've made changes to the settings (but not yet clicked [Set]), clicking this button restores the settings made the last time [Set] was clicked. Once you click [Set], [Revert] cannot be used. u EXIT Click to close the dialog box. When canceling the installation If you've cancelled an installation before it is complete, the software may not have been installed properly. Follow the instructions below to properly install the software. 1 Click on "Add or Remove Programs" in the Control Panel (page 6) and find "Install mLAN for 01X" and "mLAN Tools 2.0" in the list. 2 Delete the two programs in order: first, "Install mLAN for 01X," then "mLAN Tools 2.0." 3 Start installation again from step 12 (page 7). When the settings of the mLAN Auto Connector or Driver Setup cannot be changed, or when the program Install mLAN for 01X/mLAN Tools 2.0 cannot be uninstalled. The message below may sometimes appear when changing the settings with mLAN Auto Connector and Driver Setup or when uninstalling. When using the mLAN driver with a program such as an audio sequencer, the settings in mLAN Auto Connector and Driver Setup cannot be changed, and Install mLAN for 01X/mLAN Tools 2.0 cannot be uninstalled. Execute these operation only after closing all applications. There may be times when the settings in mLAN Auto Connector and Driver Setup cannot be changed and Install mLAN for 01X/mLAN Tools 2.0 cannot be uninstalled, even when applications are not running. This may occur in the following cases. • When Mode in the Driver Setup is set to "WDM" or "WDM + ASIO." • When the mLAN WDM driver ("mLAN Audio Out/In 01") is selected as the audio device in Windows. If this is the case, follow the instructions below before changing the settings in mLAN Auto Connector and Driver Setup and/or uninstalling Install mLAN for 01X/mLAN Tools 2.0. 1 Select [Start] ➝ [Control Panel] ➝ [Sounds and Audio Devices] ➝ [Voice]. Make sure that something other than "mLAN Audio Out/In 01" is selected for the "Voice playback" and "Voice recording" settings. 2 Select [Start] ➝ [Control Panel] ➝ [Sounds and Audio Devices] ➝ [Audio]. Make sure that something other than "mLAN Audio Out/In 01" is selected for the "Sound playback" and "Sound recording" settings. 12 TOOLS for 01X/Plug-in Effect Installation Guide