Yamaha 24N DME64N/24N V1 Owners Manual - Page 26

USB Connection, DME Designer can be used for overall zone control

Get Yamaha 24N PDF manuals and user guides View all Yamaha 24N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

Connection USB Connection Connect the DME64N/24N [USB] connector to the computer's USB connector using a USB cable. USB connections can be used in the following two ways: (1) Connect the computer to, and control the zone master DME64N/24N using the DME Designer. (2) Connect to any individual DME64N/24N and control that DME64N/24N unit using MIDI commands from a MIDI sequencer or similar software. DME Designer can be used for overall zone control, as well as sending components to the zone via the zone master. When using MIDI commands from a MIDI sequencer to directly control a DME64N/24N, HOST (see page 52) should be set to USB-1 or USB-2. NOTE The correspondence between the MIDI commands to be received/transmitted and the scene parameters can be set up using the DME Designer. NOTE The USB port being used by the DME Designer cannot also be used by a MIDI sequencer or other application. NOTE When connecting a computer to a DME64N/24N via USB, the appropriate USB-MIDI driver must be installed on the computer. Refer to the DME Designer Installation Guide for details on installing the appropriate driver. Make sure that the USB-MIDI driver THRU setting is "OFF." Zone Zone Master DME64N/24N USB Cable In the case of (1), above Ethernet Straight Cable Switching Hub Computer (DME Designer operation) Ethernet Straight Cable Ethernet Straight Cable DME64N/24N DME64N/24N USB Cable In the case of (2), above Computer (MIDI sequencer or similar operation) Preparation 26 DME64N/24N Owner's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
Preparation
Connection
DME64N/24N Owner’s Manual
26
USB Connection
Connect the DME64N/24N [USB] connector to the computer’s USB connector using a USB cable.
USB connections can be used in the following two ways:
(1) Connect the computer to, and control the zone master DME64N/24N using the DME Designer.
(2) Connect to any individual DME64N/24N and control that DME64N/24N unit using MIDI commands
from a MIDI sequencer or similar software.
DME Designer can be used for overall zone control, as well as sending components to the zone via the zone
master.
When using MIDI commands from a MIDI sequencer to directly control a DME64N/24N, HOST (see page
52) should be set to USB-1 or USB-2.
NOTE
The correspondence between the MIDI commands to be received/transmitted and the scene parameters can be set up using
the DME Designer.
NOTE
The USB port being used by the DME Designer cannot also be used by a MIDI sequencer or other application.
NOTE
When connecting a computer to a DME64N/24N via USB, the appropriate USB-MIDI driver must be installed on the
computer. Refer to the DME Designer Installation Guide for details on installing the appropriate driver.
Make sure that the USB-MIDI driver THRU setting is “OFF.”
DME64N/24N
DME64N/24N
DME64N/24N
Zone
Zone Master
USB Cable
Ethernet Straight Cable
Ethernet Straight Cable
Ethernet
Straight Cable
USB Cable
Computer
(MIDI sequencer or
similar operation)
Computer
(DME Designer operation)
Switching Hub
In the case of (1), above
In the case of (2), above