Yamaha 8300 Marching multi toms 8300 series Owners Manual - Page 1

Yamaha 8300 Manual

Page 1 highlights

JA EN ZH Marching Multi-Toms Owner's Manual 2% Quad-Type 25 Quint-Type 45 Sextet-Type ZJ01120 ϱՑ : R2 Ќ޹ߌ࣢ b b Accessories Tuning Key (1 Wrench (1) Yamaha Corporation Manual Development Group ©Yamaha Corporation Published 09/2018 ‫ڿ‬ϱ POA0 B 8 mm / ؓш  ஫ҙ / CAUTION / ᇿၩ 5).5)4 54# .54 NN This product is designed to be used with the MTH-9500/MTH-9500S (carrier) or the MTS-810B* (stand) exclusively. Be sure to use this product only with the designated carrier/stand. Use of an unsupported carrier/stand may result in damage to the instrument or personal injury. * The older generation of the MTS-810B stand comes with 12mm diameter arms. The generation can be identified by the Yamaha logo mark on the bottom part of the MTS-810B as shown below. 5).5)4 ກࡏ ࠇ.54 b b b ࣸϱ֥.54 NN֥ᆦӪфb 54 b ৽ NN CURRENT) The stand displaying this logo mark has 14mm diameter arms and can be used with this product NN b ‫ NN 54 NN ‫; OLD) The stand displaying this logo mark has 12mm diameter arms and might not be able to hold the instrument properly. In this case, please order the MTS-810B arms (14mm diameter) part ZY212700, which is sold separately NN 54 NN b

  • 1
  • 2

マーチングマルチタム
取扱説明書
Marching Multi-Toms
Owner’s Manual
行进多音鼓
使用说明书
■ 同梱品
/ Accessories /
附属零件
●チューニングキー(1個)
Tuning Key (1)
调音杆(1只)
●スパナ(1個)
Wrench (1)
扳手(1只)
a:
対辺 8
/
8 mm
/
对边 8
ZH
EN
JA
保护环境
如果需要废弃设备时,请与本地相关机构联系,获取正确的
废弃方法。请勿将设备随意丢弃或作为生活垃圾处理。
注意
/ CAUTION /
注意
この製品は専用のキャリア(MTH-9500/MTH-9500S)またはスタンド(MTS-810B*)と共に使用します。
専用のキャリアまたはスタンド以外はご使用にならないでください。
けがやトラブルの原因となります。
*
MTS-810B で製造時期の古いものはアーム径 12mm のものがございます。スタンド下部にあるヤマハロゴマークで新旧をご確認ください。(下図参照)
This product is designed to be used with the MTH-9500/MTH-9500S (carrier) or the MTS-810B* (stand) exclusively.
Be sure to use this product only with the designated carrier/stand.
Use of an unsupported carrier/stand may result in damage to the instrument or personal injury.
*
The older generation of the MTS-810B stand comes with 12mm diameter arms. The generation can be identified by the Yamaha logo mark
on the bottom part of the MTS-810B as shown below.
本产品设计专门用于 MTH-9500/MTH-9500S (托架) 或 MTS-810B* (支架)。确保在使用本产品时采用指定的托架/支架。
使用不匹配的托架/支架可能导致乐器损坏或人身伤害。
*
旧版的 MTS-810B 支架采用直径为 12 mm 的支撑臂。
该版本可通过 MTS-810B 底部的雅马哈标识进行识别,如下所示。
(新)
アーム径 14mm でそのままご使用になれます。
(CURRENT)
The stand displaying this logo mark has 14mm diameter arms and can
be used with this product.
(新版)
支架显示该标识,支撑臂直径为 14 mm,可用于本产品。
(旧)
アーム径 12mm のため正しくセッティングできない可能性があります。その場合
は別売りの MTS-810B 用アーム ( 先端 14mm 径 ) ZY212700 をお買い求めください。
(OLD)
The stand displaying this logo mark has 12mm diameter arms and might
not
be able to hold the instrument properly. In this case,
please order the MTS-810B
arms (14mm diameter) part ZY212700, which is sold separately.
(旧版)
支架显示该标识,支撑臂直径为 12 mm,在这种情况下可能无法稳固地支撑乐
器,请订购 MTS-810B 支撑臂 ( 直径为 14 mm) 部件 ZY212700,该部件单独销售。
QD-8313
クオードタイプ
/ Quad-Type /
四音鼓型
QT-8313
クイントタイプ
/ Quint-Type /
五音鼓型
ST-8313
セクステットタイプ
/ Sextet-Type /
六音鼓型
ZJ01120
版次
: R2
Yamaha Corporation
Manual Development Group
©Yamaha Corporation
Published 09/2018
改版
POA0