Yamaha A3000 Upgrade Guide For V2 - Page 25

PLAY - SETUP, Output Setup for A/D Input Signal], PLAY - CONTROL, Program Controller Setup 1], ADOut - converter

Get Yamaha A3000 PDF manuals and user guides
UPC - 027108936673
View all Yamaha A3000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

Chapter 2 Changes in PLAY MODE PLAY - SETUP - ADOut [Output Setup for A/D Input Signal]  134 The MainOut display above Knob 2 has been slightly upgraded. If you set the output destination to an effect block, the screen now indicates both the block (Ef1, Ef2, or Ef3) and effect type that is currently set for that block. Version 1 indicated only the block (Effect1, Effect2, or Effect3). PLAY - CONTROL - PgmCtl1 [Program Controller Setup 1]  136 • Knob 3 offers three additional "devices": Note Number, Velocity, and Program LFO. • The program LFO is a new feature on Version 2. To set the program LFO to modify a specific parameter, just set Knob 3 to ProgramLFO and then turn Knob 4 or Knob 5 to select the parameter. (The program LFO itself is set up at the PLAY | CONTROL PgmLF01 and PgmLF02 pages; see below.) Note that you cannot select ProgramLFO at this page if the Wave type (at the PgmLF01 page) is set to Saw or Square. • On Version 1, the Knob 3 display area showed only the controller number. On Version 2, the display shows both the controller number and the name of the corresponding device (if any). If you have set up a knob to act as controller, the knob name and transmit channel will appear next to the controller number (for example, 073/K4(5) would indicate that Knob 4 is set to operate as Controller 073 transmitting over Transmit Channel 5). • Knobs 4 and 5 include four new parameters: EF1: Width, EF2:Width, EF3:Width, and PgmLFODepth. The first three control the widths for effect blocks 1 to 3, respectively. PgmLFODepth controls the depth of the program LFO. PLAY - CONTROL - PgmCtl2 [Program Controller Setup 2]  139 The Knob 3 control type offers two new settings, +ofst(-exp) and -ofst(+exp). Like the +offset setting, these two new settings will also cause the A3000 to convert received control-change values to corresponding values in the range {0 to Range}. The difference is that +offset uses a linear conversion, +ofst(-exp) produces exponentially greater changes at lower control-change values, and ofst(+exp) produces greater changes at higher values. Chapter 2 Upgrade Reference 25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
Changes in PLAY MODE
25
Chapter 2
Chapter 2
Upgrade Reference
PLAY - SETUP -
ADOut
[Output Setup for A/D Input Signal]
134
The
MainOut
display above Knob 2 has been slightly upgraded. If you set the output
destination to an effect block, the screen now indicates both the block (
Ef1
,
Ef2
, or
Ef3
)
and effect type that is currently set for that block. Version 1 indicated only the block
(
Effect1
,
Effect2
, or
Effect3
).
PLAY - CONTROL -
PgmCtl1
[Program Controller Setup 1]
136
•
Knob 3 offers three additional “devices”:
Note Number
,
Velocity
, and
Program LFO
.
• The
program LFO
is a new feature on Version 2. To set the program LFO to modify a
specific parameter, just set Knob 3 to
ProgramLFO
and then turn Knob 4 or Knob 5 to
select the parameter. (The program LFO itself is set up at the PLAY | CONTROL
PgmLF01
and
PgmLF02
pages; see below.)
Note that you cannot select
ProgramLFO
at this page if the
Wave
type (at the
PgmLF01
page) is set to
Saw
or
Square
.
•
On Version 1, the Knob 3 display area showed only the controller number. On Version
2, the display shows both the controller number and the name of the corresponding
device (if any). If you have set up a knob to act as controller, the knob name and
transmit channel will appear next to the controller number (for example,
073/K4(5)
would indicate that Knob 4 is set to operate as Controller 073 transmitting over
Transmit Channel 5).
•
Knobs 4 and 5 include four new parameters:
EF1: Width
,
EF2:Width
,
EF3:Width
,
and
PgmLFODepth
. The first three control the widths for effect blocks 1 to 3, respec-
tively.
PgmLFODepth
controls the depth of the program LFO.
PLAY - CONTROL -
PgmCtl2
[Program Controller Setup 2]
139
The Knob 3 control type offers two new settings,
+ofst(-exp)
and
-ofst(+exp)
. Like the
+offset
setting, these two new settings will also cause the A3000 to convert received
control-change values to corresponding values in the range {0 to
Range
}. The difference
is that
+offset
uses a linear conversion,
+ofst(-exp)
produces exponentially greater changes
at lower control-change values, and
ofst(+exp)
produces greater changes at higher val-
ues.