Yamaha ATS-1060 ATS-1060 Owners Manual - Page 28

Troubleshooting

Get Yamaha ATS-1060 PDF manuals and user guides View all Yamaha ATS-1060 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

Troubleshooting Refer to the table below when the unit does not function properly. If the problem you are experiencing is not listed below or if the instructions below do not help, turn off the unit, disconnect the power cable, and contact the nearest authorized Yamaha dealer or service center. First, check the following: 1 The power cables of the unit, TV and playback devices (such as BD/DVD players) are connected to AC wall outlets securely. 2 The unit, TV and playback devices (such as BD/DVD players) are turned on. 3 The connectors of each cable are securely inserted into jacks on each device. Power and system Problem The power turns off suddenly. The power cannot be turned on. All indicators go out although the unit is turned on (it may seem that the unit is turned off). Cause When the auto power standby function is enabled, the unit automatically turns off in any of the following situations: - No operations have been performed for 8 hours - BLUETOOTH or HDMI is selected as the input source, but no audio has been input to the unit or no operations have been performed with the unit for more than 20 minutes. The protection circuitry has been activated. (The DD / DTS indicator flashes.) The Bluetooth connection was terminated by a Bluetooth device with the unit's Bluetooth standby function enabled. The protection circuitry has been activated three times consecutively. (If you try to turn on the power in this condition, the DD / DTS indicator will flash.) The unit is configured so that indicators do not glow or flash unless the unit is being operated. Remedy Turn on the unit again. If the auto power standby function is not used, disable the function (p. 27). After confirming that all connections are made properly, turn on the unit again. If the power still turns off frequently, unplug the power cable from the AC wall outlet and contact the nearest authorized Yamaha dealer or service center. Disable the Bluetooth standby function (p. 25). To protect the product, the power cannot be turned on. Unplug the power cable from the AC wall outlet and contact the nearest authorized Yamaha dealer or service center. Use the DIMMER key to select the desired brightness (p. 21). 28 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
28
En
Troubleshooting
Refer to the table below when the unit does not function properly. If the problem you are experiencing is not listed below or if the instructions
below do not help, turn off the unit, disconnect the power cable, and contact the nearest authorized Yamaha dealer or service center.
First, check the following:
1
The power cables of the unit, TV and playback devices (such as BD/DVD players) are connected to AC wall outlets securely.
2
The unit, TV and playback devices (such as BD/DVD players) are turned on.
3
The connectors of each cable are securely inserted into jacks on each device.
Power and system
Problem
Cause
Remedy
The power turns off
suddenly.
When the auto power standby function is enabled, the unit
automatically turns off in any of the following situations:
– No operations have been performed for 8 hours
– BLUETOOTH or HDMI is selected as the input source,
but no audio has been input to the unit or no operations
have been performed with the unit for more than 20
minutes.
Turn on the unit again. If the auto power standby function is not
used, disable the function (p. 27).
The protection circuitry has been activated. (The
DD /
DTS indicator flashes.)
After confirming that all connections are made properly, turn on
the unit again. If the power still turns off frequently, unplug the
power cable from the AC wall outlet and contact the nearest
authorized Yamaha dealer or service center.
The
Bluetooth
connection was terminated by a
Bluetooth
device with the unit’s
Bluetooth
standby function enabled.
Disable the
Bluetooth
standby function (p. 25).
The power cannot be turned
on.
The protection circuitry has been activated three times
consecutively. (If you try to turn on the power in this
condition, the
DD / DTS indicator will flash.)
To protect the product, the power cannot be turned on. Unplug
the power cable from the AC wall outlet and contact the nearest
authorized Yamaha dealer or service center.
All indicators go out although
the unit is turned on (it may
seem that the unit is turned
off).
The unit is configured so that indicators do not glow or
flash unless the unit is being operated.
Use the DIMMER key to select the desired brightness (p. 21).