Home » Yamaha Manuals » Musical Keyboards » Yamaha DJXPSR-D1 » Manual Viewer

Yamaha DJXPSR-D1 Owner's Manual - Page 99

Loading Bulk Data/Sampling Data, the appropriate data.

Get Yamaha DJXPSR-D1 PDF manuals and user guides

Add to My Manuals
Save this manual to your list of manuals

Page 99 highlights

MIDI FUNCTIONS Loading Bulk Data/Sampling Data Once you've saved DJX data as described above, you can easily reload the data back to the DJX. 1 Set up the connected MIDI device for sending the appropriate data. The actual procedure may differ depending on your particular equipment and software. For example, if you are using the Yamaha MDF3 MIDI Data Filer: 1) Make the appropriate MIDI connections. DJX MIDI IN MIDI OUT MDF3 2) Insert the appropriate floppy disk (containing the desired data) into the MIDI Data Filer. 2 Make sure that the DJX is set to the Style mode. Make sure that the DJX is NOT set to the Song mode, and that it is not in the middle of an operation, such as song recording or playback, pattern playback, Bulk Dump Send, etc. 3 Start sending the data from the connected MIDI device. Send the data from the connected device. (Refer to the owner's manual of the device for details.) The DJX automatically receives the data. As the data is being received, the DJX display indicates the various stages of data reception until the operation is complete: STYLE F00Rcv:Sng FUNCTION STYLE F00Rcv:PSU FUNCTION STYLE F00Rcv:Smpl FUNCTION Indicates User Song data is being received. Indicates Peformance Setup User data is being received. Indicates Sampling data is being received. • When the DJX is receiving bulk data/sampling data, none of the panel controls can be used. • Bulk data and sampling data cannot be loaded in the following conditions: • While playing a pattern • In the Song mode • In one of the Recording modes • While calling up a Performance Setup • While sending bulk/ sampling data If you attempt the function while in one of the above conditions, "- - -" appears in the display and the data is not received. 99

Section	Page
Cover	1
SPECIAL MESSAGE SECTION	2
PRECAUTIONS	3
Congratulations	4
Main Features	4
Contents	5
PANEL CONTROLS AND TERMINALS	6
Front Panel	6
Rear Panel	7
SETTING UP	8
POWER REQUIREMENTS	8
TURNING ON THE POWER	8
ACCESSORY JACKS	9
Quick Guide	10
Step 1 The DJX — Take it for a spin!	10
Step 2 Using the Keyboard	12
Step 3 Demo Song/Voice/Style	14
Step 4 Digital Sampling	16
Step 5 Function Parameters	18
Step 6 Assigning Various Controls to the ASSIGN Knob, RIBBON CONTROLLER, and Footswitch	20
PANEL DISPLAY INDICATIONS	22
PLAYING VOICES — THE VOICE MODE	24
PLAYING A VOICE — MAIN VOICE	25
About Panel Voices and GM Voices	26
Drum Kit Voice Chart (voices 141 - 155)	26
Function Parameters — Main Voice	27
TRANSPOSE AND TUNING	28
Transpose	28
Tuning	29
PLAYING TWO VOICES — DUAL VOICE	29
Function Parameters — Dual Voice	30
PLAYING TWO VOICES — SPLIT VOICE	31
Function Parameters — Split Voice	32
ADDITIONAL VOICE FUNCTIONS — VOICE SET, TOUCH SENSITIVITY, AND PITCH BEND RANGE	33
Function Parameters — Voice Set, Touch Sensitivity and Pitch Bend Range	33
EFFECTS	34
REVERB	34
CHORUS	35
DSP	36
ARPEGGIATOR	37
Function Parameters — Effects	37
Effect Types	38
SONG PLAYBACK — THE SONG MODE	40
SELECTING AND PLAYING A SONG	40
CHANGING THE BPM (TEMPO)	41
ABOUT THE BEAT DISPLAY	42
ADJUSTING THE SONG VOLUME	43
PATTERNS — THE STYLE MODE	44
SELECTING A STYLE AND PLAYING THE PATTERN	44
PATTERN CONTROLS	47
PATTERN SECTIONS (BEAT A, BEAT B AND BREAK OUTS)	48
CHANGING THE BPM (TEMPO)	48
ADJUSTING THE PATTERN VOLUME	49
FINGERING	50
BEAT REVERSE	52
PART ON/OFF	52
About the Parts	53
SETTING THE PATTERN SPLIT POINT	54
Function Parameter — Pattern Split Point	55
PERFORMANCE SETUP	56
PERFORMANCE SETUP — USER	56
Recording a User Performance Setup	56
Recalling a User Performance Setup	57
Selecting a User Bank	57
PERFORMANCE SETUP — PRESET	58
Selecting a Preset Performance Setup	58
THE KNOBS	59
USING THE KNOBS	59
About CUTOFF and RESONANCE	62
About GROOVE	62
ASSIGN KNOB	63
ASSIGN Knob Parameters	64
RIBBON CONTROLLER	66
USING THE RIBBON CONTROLLER	66
RIBBON CONTROLLER Parameters	67
How the RIBBON CONTROLLER works	68
DIGITAL SAMPLING	69
ABOUT DIGITAL SAMPLING	69
RECORDING A SAMPLE AND PLAYING IT	70
Guidelines for sampling	71
Trigger Level	71
Sampling memory capacity	73
Deleting a sample	74
Recording additional samples	74
SAMPLE EDITING	75
Setting the End Point	75
Creating Loops	78
About the resolution settings	79
SONG RECORDING	80
RECORDING A USER SONG — REALTIME RECORDING	81
Additional Operations	84
RECORDING A USER SONG — STEP RECORDING	85
Recording Notes	86
Additional Operations	88
Replacing a Note or Rest	89
Entering Velocity Curves	90
Velocity Curve Chart	90
CLEARING A SONG	91
MIDI FUNCTIONS	92
WHAT IS MIDI?	92
Channel Messages	93
System Messages	93
CONNECTING TO A PERSONAL COMPUTER	94
MIDI Terminals	94
FUNCTION PARAMETERS — MIDI	95
USING BULK DUMP SEND/SAMPLING SEND TO SAVE DATA	97
Saving Bulk Data/Sampling Data	97
Loading Bulk Data/Sampling Data	99
USING INITIAL SETUP SEND WITH A SEQUENCER	100
Sending Initial Setup Data	100
Appendix	102
TROUBLESHOOTING	102
DATA BACKUP & INITIALIZATION	103
VOICE LIST	104
DRUM KIT LIST	108
STYLE LIST	111
MIDI IMPLEMENTATION CHART	112
SPECIFICATIONS	115