Yamaha HTR-5450RDS Owner's Manual - Page 57

Refer to, Problem, Cause, Remedy, DIGITAL OUTPUT jack

Get Yamaha HTR-5450RDS PDF manuals and user guides View all Yamaha HTR-5450RDS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

INTRODUCTION TROUBLESHOOTING Problem The volume level cannot be increased, or the sound is distorted. The effect and surround sounds cannot be recorded. A source cannot be recorded by a digital recording component connected to the DIGITAL OUTPUT jack of this unit. The settings of the SET MENU and some other settings on this unit cannot be changed. This unit does not operate properly. The sound is degraded when listening with headphones connected to a tape deck or CD player that is connected to this unit. There is noise interference from digital or high-frequency equipment, or the unit. Cause The component connected to the REC OUT jacks of this unit is turned off. It is not possible to record the effect and surround sounds by a recording component. A source component is only connected to the analog input jacks of this unit. "9 MEM. GUARD" in the SET MENU is set to ON. The internal microcomputer has been frozen by an external electric shock (such as lightning or excessive static electricity) or by a power supply with low voltage. This unit is in the standby mode. The unit is too close to the digital or highfrequency equipment. Remedy Turn on the power to the component. Refer to page - 34 Connect the source component to the digital input jacks of this unit. 12 - 15 Select OFF. 39 Disconnect the AC power cord from the outlet - and then plug it in again after about 30 seconds. Turn on the power of the unit. - Move the unit further away from such - equipment. PREPARATION BASIC OPERATION ADVANCED OPERATION APPENDIX English 55

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
55
English
BASIC OPERATION
ADVANCED OPERA
TION
APPENDIX
INTRODUCTION
PREPARATION
TROUBLESHOOTING
12
–
15
The volume level cannot
be increased, or the
sound is distorted.
The component connected to the REC OUT
jacks of this unit is turned off.
Turn on the power to the component.
The effect and surround
sounds cannot be
recorded.
It is not possible to record the effect and
surround sounds by a recording component.
A source cannot be
recorded by a digital
recording component
connected to the
DIGITAL OUTPUT jack of
this unit.
A source component is only connected to the
analog input jacks of this unit.
Connect the source component to the digital
input jacks of this unit.
The settings of the SET
MENU and some other
settings on this unit
cannot be changed.
“
9 MEM. GUARD
”
in the SET MENU is set
to ON.
Select OFF.
This unit does not
operate properly.
The internal microcomputer has been frozen by
an external electric shock (such as lightning or
excessive static electricity) or by a power
supply with low voltage.
Disconnect the AC power cord from the outlet
and then plug it in again after about 30 seconds.
The sound is degraded
when listening with
headphones connected
to a tape deck or CD
player that is connected
to this unit.
This unit is in the standby mode.
Turn on the power of the unit.
There is noise
interference from digital
or high-frequency
equipment, or the unit.
Move the unit further away from such
equipment.
—
—
—
Refer to
page
The unit is too close to the digital or high-
frequency equipment.
Problem
Cause
Remedy
34
39
—