Yamaha MA2030a MA2030a/PA2030a Technical Specifications - Page 1

POWER AMPLIFIER ZV75870 Technical Specifications Specifications Outputs (Speaker Out) Output power 20msec burst (THD+N=1%) Terminal 3, 4, 8ohms 70V 100V MA2030a PA2030a 30W x 2ch 60W x 1ch 60W x 1ch 7.62mm barrier strip 4pin Outputs (Line Out) Line Out (MA2030a only) Output Level Terminal Actual source impedance For use with nominal Nominal MA2030a 600Ω 10kΩLines -10dBV (316.2mV) STEREO RCA PIN, unbalanced PA2030a - - - - Inputs MIC IN 1-2 (MA2030a only) Terminal STEREO IN Input Level (ST SOURCE Gain is set to maximum) Input Level (balance) (PA2030a only) Terminal (MA2030a) MIC IN 1 MIC IN 2 Sensitivity Nominal Max before clip Sensitivity Nominal Max before clip STEREO IN 1 Terminal (PA2030a) STEREO IN 2, 3 LINE IN (Unbalance) LINE IN (Balance) Electrical Characteristics Amplifier type (Output circuitry) THD+N 1kHz, 15W, 3Ω/4Ω/8Ω Stereo In to Speaker Out 1kHz, 30W, 70V/100V Stereo In to Speaker Out Frequency response Line In to Line Out 20 to 20kHz (MA2030a only) Line In to Speaker Out 50 to 20kHz, 1W, 3 or 4 or 8ohms Line In to Speaker Out 90 to 20kHz, 1W, 70/100V Crosstalk Stereo In to other Stereo In (MA2030a only) Load protection POWER switch on/off Output voltage protection DC-fault Amplifier protection Thermal Over current Integrated power limit Power supply protection Thermal Over voltage Over current Cooling MA2030a PA2030a XLR combo jack, balanced - 3.5mm Euroblock 3pin, balanced - -10.0 dBV (316.2 mV) -10.0 dBV (316.2 mV) 10.0 dBV (3.162 V) - 4.0dBu (1.228V) - 4.0dBu (1.228V) - 24dBu (12.283V) STEREO mini Phone (3.5mm), unbalanced - STEREO RCA PIN, unbalanced - - STEREO RCA PIN, unbalanced - 3.5mm Euroblock 3pin x 2 Class D ≤ 0.1% ≤ 0.2% 0dB, -2.5dB, +1.0dB 0dB, -3.0dB, +1.0dB 0dB, -3.0dB, +1.0dB ≤ -70dB Mute the output Compress output voltage when needed Power supply shutdown Limit output " Mute " Shutdown Mute the output (with automatic restoration) Compress output Power supply shutdown Power supply shutdown Limit power " Power supply shutdown Conventional cooling, bottom to up airflow MA2030a PA2030a Controls Front Panel POWER switch (seesaw), MIC IN 1 volume x 1, ST SOURCE encoder x 1 OUTPUT Volume x 1, BASS EQ Volume x 1, TREBLE EQ Volume x 1 POWER switch (seesaw), OUTPUT Volume x 1, Rear Panel AMP SETTING switch (100V | 70V | 3Ω/4Ω/8Ω ), SETUP switch (3Ω/4Ω/8Ω, SPEAKER EQ SURFACE/CEILING/HPF 150Hz, MIC1 DUCEKER, MIC2 DUCKER, STEREO/MONO, LEVELER), MIC IN 2 Volume x 1 AMP SETTING switch (100V | 70V | 3Ω/4Ω/8Ω ), SETUP switch (3Ω/4Ω/8Ω, SPEAKER EQ SURFACE/CEILING/VXS10S(T)/ HPF 150Hz/LPF 150Hz/LPF 200Hz, STEREO/MONO) Connectors Analog In (Mic input) XLR/PHONE combo x 1 (Front), Euroblock x 1 (Rear) - Analog In (Line) Stereo mini x 1 (Front), Stereo RCA x 2 (Rear) Euroblock x 2 (Rear), Stereo RCA x 1 (Rear) Analog Out (Line) Stereo RCA x 1 (Rear) - Speakers Barrier strip/ch Remote RJ45 x 1 (DCP) - Power AC inlet x1 Indicators POWER x 1 (Green), MIC IN 1 SIGNAL x 1 (Green), ST SOURCE x 3 (Green), OUTPUT SIGNAL x 1 (Green), POWER x 1 (Green), OUTPUT SIGNAL x 1 (Green), OUTPUT LIMIT x 1 (Red) OUTPUT LIMIT x 1 (Red) AC power requirement 100V, 120V, 230V-240V 50Hz/60Hz (*1) *1  It has confirmed that it is working with ±10% of the voltage of the rated supply voltage. Power consumption 1/8 MAX power, 3Ω, AC100V, Pink noise at all channel 30W 30W Idle, 3Ω, AC100V 25W 25W Precautions for rack mounting Rack mountable (Leave more than 1U of spaces between this unit and others.) Operating temperature 0°C to +40°C Storage temperature -20°C to +60°C General Specifications Dimensions (W x H x D, including knob) Net weight Included accessories Optional accessories MA2030a PA2030a 215mm x 54mm x 288 mm 8.5 x 2.1 x 11.4 inch 1.8kg AC power cord (2.0m) x 1, Euroblock connector (3P) x 1, Owner's Manual x 1, Specification sheet x1 AC power cord (2.0m) x 1, Euroblock connector (3P) x 2, Owner's Manual x 1, Specification sheet x1 Rack-mount Accessory (RKH1) Digital Control Panel (DCP1V4S-US/-EU) Current Draw 1/8 power is typical of program material with occasional clipping. Refer to these figures for most applications. 1/3 power represents program material with extremely heavy clipping Test signal: Pink Noise, bandwidth limited from 22Hz to 22kHz 1W = 0.860kcal/h, 1BTU = 0.252kcal Note that Line Voltage [V] x Line Current [A] = [VA], not equals to [W] Power Spec (PINK NOISE,100V/50Hz mains) MODE standby idle 30W/3Ω 30W/4Ω 1/8 output power 30W/8Ω 60W/70V 60W/100V 30W/3Ω 30W/4Ω 1/3 output power 30W/8Ω 60W/70V 60W/100V Line Current (A) 0.08A 0.28A 0.48A 0.47A 0.45A 0.44A 0.44A 0.87A 0.84A 0.74A 0.69A 0.68A Power Consumption (W) 0.1W 14W 27W 26W 24W 24W 24W 52W 49W 43W 40W 40W Watts Dissipated (W) 0.1W 14W 20W 19W 17W 17W 17W 32W 29W 23W 20W 20W Heat Dissipation Btu/h kcal/h 0.3 0.1 48 12 67 17 63 16 56 14 56 14 56 14 109 28 99 25 78 20 68 17 68 17 Power Spec (PINK NOISE,120V/60Hz mains) MODE standby idle 30W/3Ω 30W/4Ω 1/8 output power 30W/8Ω 60W/70V 60W/100V 30W/3Ω 30W/4Ω 1/3 output power 30W/8Ω 60W/70V 60W/100V Line Current (A) 0.12A 0.27A 0.44A 0.42A 0.40A 0.39A 0.39A 0.77A 0.74A 0.64A 0.59A 0.59A Power Consumption (W) 0.1W 14W 27W 26W 24W 23W 24W 52W 49W 42W 39W 39W Watts Dissipated (W) 0.1W 14W 20W 19W 17W 16W 17W 32W 29W 22W 19W 19W Heat Dissipation Btu/h kcal/h 0.4 0.1 48 12 67 17 63 16 56 14 53 13 56 14 109 28 99 25 75 19 65 16 65 16 Power Spec (PINK NOISE,230V/50Hz mains) MODE standby idle 30W/3Ω 30W/4Ω 1/8 output power 30W/8Ω 60W/70V 60W/100V 30W/3Ω 30W/4Ω 1/3 output power 30W/8Ω 60W/70V 60W/100V Line Current (A) 0.19A 0.25A 0.33A 0.32A 0.32A 0.31A 0.31A 0.50A 0.49A 0.44A 0.41A 0.41A Power Consumption (W) 0.4W 16W 28W 27W 26W 25W 25W 51W 49W 42W 39W 39W Watts Dissipated (W) 0.4W 16W 20W 19W 18W 17W 17W 31W 29W 22W 19W 19W Heat Dissipation Btu/h kcal/h 1.4 0.3 53 13 69 17 65 16 62 16 59 15 59 15 107 27 100 25 76 19 64 16 64 16 Dimensions MA2030a 215 260 288 44 54 PA2030a 215 260 288 44 54 (unit: mm) Block Diagram MA2030a G MIC IN 1 MIC IN 2 HA AD VOLUME HA AD GAIN ST IN1 ST IN2 AD ST IN3 Analog Switch DCP IN1 IN2 IN3 STEREO SOURCE SIGNAL HPF HPF Feedback Suppressor TRIGGER LEVELER VOL SOURCE EQ /ENHANCER ON/OFF BASS TREBLE MIXER DSP Process Ducker ON/OFF DCP Volume HPF 80Hz OFF SPEAKER EQ VOLUME ON/OFF SURFACE/CEILING HPF 150Hz LIMIT SIGNAL MUTE LIMITER MIC IN1 ON/OFF MIC IN2 ON/OFF CHIME GEN. STEREO /MONO Switch STEREO /MONO TEMP OUTPUT VOLTAGE INTEGRAL OUTPUT POWER AMP PROTECTION LOGIC OUTPUT FORMAT 100V SPEAKERS 70V DA 8ohms AMP 4ohms 3ohms LINE OUT DC-FAULT OUTPUT CURRENT AMP PROTECTION HARDWARE POWER SUPPLY PA2030a L R L R LINE IN G G MIXER AD DSP Process AD HPF LIMIT SIGNAL OUTPUT FORMAT 100V SPEAKERS 80Hz 70V SPEAKER EQ VOLUME MUTE LIMITER DA 8ohms AMP OFF 4ohms AD ON/OFF 3ohms AD SURFACE/CEILING HPF 150Hz VXS10S(T) LPF 150Hz LPF 200Hz TEMP STEREO /MONO Switch STEREO /MONO OUTPUT VOLTAGE INTEGRAL OUTPUT POWER AMP PROTECTION LOGIC DC-FAULT OUTPUT CURRENT AMP PROTECTION HARDWARE POWER SUPPLY Level Diagram MICIN 1 (MAX.：-9dBu) [NOM.：-53dBu] ※ MA2030a only COMBO JACK LINEIN L 3.5mm EURO BLOCK (MAX.：+24dBu) + [NOM.：+4dBu] - ※※ PA2030a only G MICIN 2 (MAX.：-9dBu) [NOM.：-53dBu] ※ MA2030a only 3.5mm EURO BLOCK + G LINEIN R 3.5mm EURO BLOCK (MAX.：+24dBu) + [NOM.：+4dBu] - ※※ PA2030a only G ST IN 1-L/R (MAX.：+12.2dBu) [NOM.：-10dBV=-7.8dBu] ※ MA2030a only ST IN 2 (MA2030a) L LINE IN (PA2030a) (MAX.：+12.2dBu) [NOM.：-10dBV=-7.8dBu] R ST IN 3 L (MAX.：+12.2dBu) [NOM.：-10dBV=-7.8dBu] R ※ MA2030a only GAIN:29.0dB normal HA phase GAIN +10.7dB @Vol=Max. +0.7dB @Vol=Nominal BA normal phase MICIN 1 GAIN GAIN:-21.3dB normal HA phase GAIN:29.0dB normal HA phase GAIN +10.7dB @Vol=Max. +0.7dB @Vol=Nominal BA normal phase GAIN:-21.3dB normal HA phase INV inverted phase GAIN:-9.5dB inverted INV phase INV inverted phase GAIN:-9.5dB inverted INV phase INV inverted phase GAIN:-9.5dB inverted INV phase MICIN 2 GAIN ※※ PA2030a only SEL INV normal phase GAIN:0dB INV normal phase +60 IN ADC normal phase IN ADC normal phase IN ADC normal phase IN ADC normal phase DSP normal phase normal phase normal phase normal phase DAC OUT inverted phase INV DAC OUT GAIN:+9.2dB normal phase + inverted phase LPF - normal phase ATT inverted phase INV DAC OUT DAC OUT GAIN:+9.2dB inverted phase + normal phase LPF - inverted phase 100V：GAIN=0dB 70V：GAIN=-3.0dB 8Ω：GAIN=-10.2dB 4Ω：GAIN=-13.2dB 3Ω：GAIN=-14.4dB ATT inverted phase INV DAC OUT inverted phase INV DAC OUT DAC OUT DAC OUT inverted phase GAIN:+9.2dB + LPF normal phase - inverted phase GAIN:+9.2dB + LPF normal phase - inverted phase inverted phase 100V：GAIN=0dB 70V：GAIN=-3.0dB 8Ω：GAIN=-10.2dB 4Ω：GAIN=-13.2dB 3Ω：GAIN=-14.4dB INV inverted phase GAIN:0dB INV normal phase GAIN:0dB INV normal phase GAIN:-7.7dB normal INV phase ST SOURCE VOLUME GAIN +50 Analog Digital Digital Analog +40 +30 +20 +10 0 (MA2030a LINE OUT) -10dBV=-7.8dBu -10 -20 -30 -40 PA2030a EURO Max.INPUT Level(+24dBu) ST IN Max. INPUT Level(+12.2dBu) PA2030a EURO INPUT SENSITIVITY[+4dBu] ST IN INPUT SENSITIVITY[-7.8dBu] MIC IN Max. INPUT Level(-9dBu) HA OUT Max.(+20.0dBu) ST IN Head Room Margin:20dB ADC 0dBFS(+2.7dBu) Unbalance MIC IN Head Room Margin:26dB DSP MIX OUT to SPEAKER OUT:+18dB DSP Digital dBFS 0 Digital dBFS 0 +2.7dBu -10 -10 ST IN to DSP MIX IN:+0dB -20 -20 Head Room Margin:2dB DAC 0dBFS(+10.7dBu)Balance DAC OUT[+8.7dBu]Balance LPF(+19.9dBu) +17.9dBu -0.1dBu -9.3dBu -17.3dBu -23.3dBu -34dBu Vol=Max. -30 -30 DSP MIX OUT to LINE OUT:+0dB -40 -40 -50 -50 +17.9dBu +14.9dBu +7.7dBu +4.7dBu +3.5dBu -50 -60 MIC IN Min. INPUT Level[-63dBu] ST IN ADC Nom.Input(-17.3dBu)Unbalance MIC IN ADC Nom.Input(-23.3dBu)Unbalance -70 MIC IN to DSP MIX IN:+6dB GAIN:+18.3dB P-AMP (-1) normal phase GAIN:+18.3dB P-AMP (-1) inverted phase ＋ SPEAKER OUT A (SE) ー 8Ω:30W@8ΩLOAD (THD+N=1%) 4Ω:30W@4ΩLOAD (THD+N=1%) 3Ω:30W@3ΩLOAD (THD+N=1%) SPEAKER OUT 100V/70V (BTL) ー SP OUTPUT B (SE) ＋ 8Ω:30W@8ΩLOAD (THD+N=1%) 4Ω:30W@4ΩLOAD (THD+N=1%) 3Ω:30W@3ΩLOAD (THD+N=1%) LINE OUT L LINE OUT R +60 BTL:+6dB +50 Hi-Z 100V BTL[+42.2dBu] Hi-Z 70V BTL[+39.2dBu] +40 +30 30W 8Ω SE[+26.0dBu] 30W 4Ω SE[+23.0dBu] 30W 3Ω SE[+21.8dBu] +20 +10 0 LINE OUT[-10dBV=-7.8dBu] -10 -20 -30 -40 -50 -60 -70 Notice All internal equalizer settings are "Flat" position and all internal dynamics effects are "OFF" position. ST SOURCE Gain is set to Maximum. * The contents of this manual apply to the latest specifications as of the publishing date. To obtain the latest manual, access the Yamaha website then download the manual file. * Der Inhalt dieser Bedienungsanleitung gilt für die neuesten technischen Daten zum Zeitpunkt der Veröffentlichung. Um die neueste Version der Anleitung zu erhalten, rufen Sie die Website von Yamaha auf und laden Sie dann die Datei mit der Bedienungsanleitung herunter. * Le contenu de ce mode d'emploi s'applique aux dernières caractéristiques techniques connues à la date de publication du manuel. Pour obtenir la version la plus récente du manuel, accédez au site Web de Yamaha puis téléchargez le fichier du manuel concerné. * El contenido de este manual se aplica a las últimas especificaciones según la fecha de publicación. Para obtener el último manual, acceda al sitio web de Yamaha y descargue el archivo del manual. * O conteúdo deste manual se aplica às especificações mais recentes a partir da data de publicação. Para obter o manual mais recente, acesse o site da Yamaha e faça o download do arquivo do manual. * Il contenuto del presente manuale si applica alle ultime specifiche tecniche a partire dalla data di pubblicazione. Per ottenere la versione più recente del manuale, accedere al sito Web Yamaha e scaricare il file corrispondente. Yamaha Yamaha