Yamaha MCX-RC100 Getting Started - Page 2

(continued from the front side) 5. $POUSPM QBE Enter the security key used by the selected access point and then select "OK". ;0/& .64*$ 3&.05& 70-6.& .65& ;0/& .64*$ 3&.05& #"$, )0.& ê /&5803,

.64*$

$0.."/%&3

.$93$ 70-6.& .65& #"$, )0.& /&5803,

.64*$

$0.."/%&3

.$93$ Now the Music Commander is connected to your WiFi router. 6. Make sure that no network cable is connected to the Music Player (MCX-A300 or MCX-P200). y If you want to make a wired connection between the Music Player and WiFi router, use a network cable to connect them and then turn on the Music Player. In this case, you can skip the following steps. ;0/& 7. Music Commander: 8. Music Player: While holding down MUTE, turn on the Music Player. ê Lights in umber 8*3&-&44 -"/ The "Client WiFi Setup" screen appears on the Music Commander. ;0/& .64*$ 3&.05& 70-6.& .65& #"$, )0.& /&5803,

.64*$

$0.."/%&3

.$93$ & Perform step 9 within three minutes. If it failed, your Music Player will exit the WiFi setup process. In this case, turn off the Music Player and then perform step 8 again. 9. Music Commander: :FT → &YJU ;0/& .64*$ 3&.05& 70-6.& .65& ;0/& .64*$ 3&.05& #"$, )0.& ê /&5803,

.64*$

$0.."/%&3

.$93$ 70-6.& .65& ê LightU in green #"$, )0.& /&5803,

.64*$

$0.."/%&3

.$93$ 8*3&-&44 -"/ & If "WiFi Setup uncompleted" appears, turn off the Music Player and then perform from step 8 again. Now the Music Player is connected to your WiFi router. 4 Playback Now you are ready to enjoy digital music distribution. As a system test, follow the procedure below to start to listen to Internet Radio stations using your MusicCAST2 products or Yamaha network receiver (RXV3900, etc) connected to your WiFi router. This unit uses the vTuner Internet Radio station database service particularly customized for this unit. & To output audio source at your receiver, you need to prepare the receiver for playback (turning on power, selecting input source, etc). For details, refer to the manual supplied with it. ;0/& 1. Music Commander: 2. $POUSPM QBE Select the device (zone) to which audio source is delivered. ;0/& .64*$ 3&.05& 70-6.& .65& ;0/& .64*$ 3&.05& 70-6.& .65& #"$, )0.& ê /&5803,

.64*$

$0.."/%&3

.$93$ #"$, )0.& /&5803,

.64*$

$0.."/%&3

.$93$ .64*$ 3&.05& 3. → $POUSPM QBE [Net Radio] ;0/& .64*$ 3&.05& 70-6.& .65& ;0/& .64*$ 3&.05& 70-6.& .65& #"$, )0.& ê /&5803,

.64*$

$0.."/%&3

.$93$ #"$, )0.& /&5803,

.64*$

$0.."/%&3

.$93$ 4. $POUSPM QBE Select an Internet Radio channel you want to listen to. ;0/& .64*$ 3&.05& 70-6.& .65& ;0/& .64*$ 3&.05& #"$, )0.& ê /&5803,

.64*$

$0.."/%&3

.$93$ 70-6.& .65& ;0/& .64*$ 3&.05& #"$, )0.& ê /&5803,

.64*$

$0.."/%&3

.$93$ 70-6.& .65& #"$, )0.& /&5803,

.64*$

$0.."/%&3

.$93$ 5. If playback starts, use the playback control buttons to operate desired functions. Start playback Pause (stop) playback 70-6.& Adjust the volume level .65& Turn on/off the audio mute y Playback control operations always work on the playback on the device (zone) selected in the "Zone" screen (shown in step 2). Playback screen [ a ] [ b ] ;0/& .64*$ 3&.05& [ c ] 70-6.& .65& #"$, )0.& /&5803,

.64*$

$0.."/%&3

.$93$ [ a ] Playback status ( : Play, [ b ] Station logo (if available) [ c ] Station name : Mute) 6. #"$, (to the previous menu screen) ;0/& .64*$ 3&.05& 70-6.& .65& ;0/& .64*$ 3&.05& #"$, )0.& ê /&5803,

.64*$

$0.."/%&3

.$93$ 70-6.& .65& #"$, )0.& /&5803,

.64*$

$0.."/%&3

.$93$ 7. )0.& (to the top menu screen) ;0/& .64*$ 3&.05& 70-6.& .65& ;0/& .64*$ 3&.05& #"$, )0.& ê /&5803,

.64*$

$0.."/%&3

.$93$ 70-6.& .65& #"$, )0.& /&5803,

.64*$

$0.."/%&3

.$93$ In case you need to turn off the Music Commander 1 ;0/& Music Commander: → 4FUVQ 2 $POUSPM QBE [Power Saving] - [Power Off] ;0/& .64*$ 3&.05& 70-6.& .65& #"$, )0.& /&5803,

.64*$

$0.."/%&3

.$93$