Yamaha MG10XU Technical Specifications - Page 1

MIXING CONSOLE ZJ12600 Technical Specifications General Specifications 0 dBu = 0.775 Vrms Output impedance of signal generator (Rs) = 150Ω All level knobs are nominal if not specified. Frequency Response Input to STEREO OUT +0.5 dB/-1.0 dB (20 Hz to 48 kHz), refer to the nominal output level @1 kHz, GAIN knob: Min Total Harmonic Distortion (THD+N) Input to STEREO OUT 0.02 % @ +14 dBu (20 Hz to 20 kHz), GAIN knob: Min 0.003 % @ +24 dBu (1 kHz), GAIN knob: Min Hum&Noise *1 (20 Hz to 20 kHz) Equivalent Input Noise -128 dBu (Mono Input Channel, Rs: 150 Ω, GAIN knob: Max) Residual Output Noise -102 dBu (STEREO OUT, STEREO LEVEL knob: Min) Crosstalk (1 kHz) *2 -83 dB Input Channels 10 channels: Mono [MIC/LINE]: 4, Stereo [LINE]: 3 Ouput Channels STEREO OUT: 2, PHONES: 1, MONITOR OUT: 1, AUX (FX) SEND: 1 Bus Stereo: 1, AUX (FX): 1 PAD CH1 - CH4 26 dB HPF CH1 - CH4 80 Hz, 12 dB/oct Input Channel Function COMP CH1 - CH2 1-knob compressor Threshold: +22 dBu to -8 dBu, Ratio:1:1 to 4:1, Output level: 0 dB to 7 dB, Attack time: approx. 25 msec, Release time: approx. 300 msec CH1 - CH9/10 HIGH: Gain: +15 dB/-15 dB, Frequency: 10 kHz shelving EQ CH1 - CH4 MID: Gain: +15 dB/-15 dB, Frequency: 2.5 kHz peaking CH1 - CH9/10 LOW: Gain: +15 dB/-15 dB, Frequency: 100 Hz shelving PEAK LED CH1 - CH4 LED turns on when post EQ signal reaches 3 dB below clipping (+17 dBu) Level Meter Post STEREO LEVEL Knob 2×7 -segment LED meter [PEAK (+17), +10, +6, 0, -6, -10, -20 dB] Internal Digital Effect (MG10XU) SPX Algorithm 24 programs USB Audio (MG10XU) 2 IN / 2 OUT USB Audio Class 2.0 compliant Sampling Frequency: Max 192 kHz, Bit Depth: 24-bit Phantom Power Voltage +48 V Power Supply Adaptor PA-10 (AC 38 VCT, 0.62A, Cable length = 3.6 m) or equivalent recommended by Yamaha Power Consumption 22.9 W Dimensions (W×H×D) 244 mm×71 mm×294 mm (9.6" × 2.8" × 11.6") Net Weight MG10XU: 2.1 kg (4.6 lbs.), MG10: 1.9 kg (4.1 lbs.) Included Accessory AC Adaptor, Cubase AI Download Information (MG10XU), Owner's Manual, Precautions, Technical Specifications (this leaflet) Optional Accessory Mic Stand Adaptor: BMS-10A Operating Temperature 0 to +40°C *1 Noise is measured with A-weighting filter. *2 Crosstalk is measured with 1 kHz band pass filter. Analog Input Characteristics Input Jacks MIC/LINE 1 - 4 LINE 5/6, 7/8 LINE 9/10 PAD 26 dB OFF ON GAIN Actual Trim Load Position Impedance For Use With Nominal Sensitivity *1 +64 dB +20 dB +38 dB -6 dB 3 kΩ 50-600 Ω Mics/Lines -72 dBu (0.195 mV) -28 dBu (30.9 mV) -46 dBu (3.884 mV) -2 dBu (615.6 mV) Input level Nominal -60 dBu (0.775 mV) -16 dBu (122.8 mV) -34 dBu (15.46 mV) +10 dBu (2.451 V) - - 10 kΩ 600 Ω Lines -22 dBu (61.56 mV) -10 dBu (245.1 mV) Max. before clip -40 dBu (7.75 mV) +4 dBu (1.228 mV) -14 dBu (154.6 mV) +30 dBu (24.51 V) +10 dBu (2.451 V) Connector Combo jack*2 (Balanced) Phone jack *3 RCA Pin (Unbalanced) Phone jack *3 (Unbalanced) 0 dBu is referenced to 0.775 Vrms. *1 Sensitivity is the lowest level that will produce an output of +4dBu (1.228V) or the nominal output level when the unit is set to maximum gain (all level knobs are maximum position). *2 1&Sleeve = Ground, 2&Tip = Hot, 3&Ring = Cold *3 Tip = Signal, Sleeve = Ground Analog Output Characteristics Output Terminals Actual Source Impedance STEREO OUT [L, R] 75 Ω MONITOR OUT [L, R] AUX (FX) SEND PHONES 150 Ω 110 Ω 0 dBu is referenced to 0.775 Vrms. *1 1 = Ground, 2 = Hot, 3 = Cold *2 Tip = Hot, Ring = Cold, Sleeve = Ground For Use With Nominal 600 Ω Lines 10 kΩ Lines 40 Ω Lines Output level Nominal Max. before clip +4 dBu (1.228 V) +24 dBu (12.28 V) +4 dBu (1.228 V) 3 mW + 3 mW +20 dBu (7.750 V) 100 mW + 100 mW Connector XLR-3-32 *1 Phone jack *2 (Balanced) Phone jack *2 (Impedance Balanced) Stereo phone jack Digital Input / Output Characteristics Output Terminals USB Format USB Audio Class 2.0 Data Length*1 16 /24 bit Fs 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz *1 Data length depends on the particular audio format being used. USB Audio Class2.0: 16 / 24-bit, Yamaha Steinberg USB Driver: 24-bit Connector USB Standard-B European Models Inrush Current based on EN 55103-1:2009 1 A (on initial switch-on) 1 A (after a supply interruption of 5s) Conforms to Environments: E1, E2, E3 and E4 Specifications and descriptions in this document are for informational purposes only. Yamaha Corporation reserves the right to modify products or specifications at any time without prior notice. Since specifications, equipment, and options may not be the same in every locale, please check with your Yamaha dealer. See reverse side for block/level diagrams and dimensions.