Yamaha MG20XU Technical Specifications - Page 1
Yamaha MG20XU Manual
View all Yamaha MG20XU manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
ZK26480 Technical Specifications General Specifications 0 dBu = 0.775 Vrms, Output impedance of signal generator (Rs) = 150 Ω All level controls are nominal if not specified. Frequency Response Total Harmonic Distortion (THD+N) Hum & Noise *1 (20 Hz to 20 kHz) Crosstalk(1 kHz) *2 Input channels Output channels Bus Input Channel Function Level Meter Built-in Effect (MG20XU) USB Audio (MG20XU) Phantom Power Voltage Power Requirements Power Consumption Dimensions (W × H × D) Net Weight Included Accessory Optional Accessory Operating Temperature Input to STEREO OUT Input to STEREO OUT Equivalent Input Noise Residual Output Noise PAD HPF COMP EQ PEAK LED Pre Monitor LEVEL SPX Algorithm 2 IN / 2 OUT +0.5 dB/-1.5 dB (20 Hz to 48 kHz) , refer to the nominal output level @ 1 kHz, GAIN knob: Min 0.03 % @ +14 dBu (20 Hz to 20 kHz), GAIN knob: Min 0.005 % @ +24 dBu (1 kHz), GAIN knob: Min -128 dBu (Mono Input Channel, Rs: 150 Ω, GAIN knob: Max) -102 dBu (STEREO OUT, STEREO master fader: Min) -78 dB 20 channels: Mono [MIC/LINE]: 12, Mono/Stereo [MIC/LINE]: 2, Stereo [LINE]: 2 STEREO OUT: 2, PHONES: 1, MONITOR OUT: 1, AUX SEND: 4, GROUP OUT: 4 STEREO: 1, GROUP: 4, AUX: 4 (MG20XU: incl. FX) CH 1 - CH 12 26 dB CH 1 - CH 12, 80 Hz, 12 dB/oct CH 13/14 (MIC) - CH 19/20 (MIC) CH 1 - CH 8 1 knob compressor (Gain/Threshold/Ratio) Threshold: +22 dBu to -8 dBu, Ratio: 1:1 to 4:1, Output level: 0 dB to 7 dB, Attack time: approx. 25 msec, Release time: approx. 300 msec CH 1 - CH 12 HIGH: Gain: +15 dB/-15 dB, Frequency: 10 kHz shelving MID: Gain: +15 dB/-15 dB, Frequency: 250 Hz to 5 kHz peaking LOW: Gain: +15 dB/-15 dB, Frequency: 100 Hz shelving CH 13/14 - CH 19/20 HIGH: Gain: +15 dB/-15 dB, Frequency: 10 kHz shelving MID: Gain: +15 dB/-15 dB, Frequency: 2.5 kHz peaking LOW: Gain: +15 dB/-15 dB, Frequency: 100 Hz shelving CH 1 - CH 19/20 LED turns on when post EQ signal reaches 3 dB below clipping level 2 × 12 -segment LED meter [PEAK, +10, +6, +3, 0, -3, -6, -10, -15, -20, -25, -30 dB] 24 programs, PARAMETER control: 1, FOOT SW: 1 (FX RTN CH on/off) USB Audio Class 2.0 compliant, Sampling Frequency: Max 192 kHz, Bit Depth: 24-bit +48 V AC 100-240 V, 50 Hz/60 Hz 36 W 444 mm × 130 mm × 500 mm (17.5" × 5.1" × 19.7") MG20XU: 7.1 kg (15.7 lbs.), MG20: 6.9 kg (15.2 lbs.) AC power cord, Rack mount kit, Cubase AI Download Information (MG20XU), Owner's Manual, Technical Specifications (this leaflet) Foot Switch: FC5 (MG20XU) 0 to +40 °C *1 Noise is measured with A-weighting filter. *2 Crosstalk is measured with 1 kHz band pass filter. Specifications and descriptions in this document are for information purposes only. Yamaha Corp. reserves the right to change or modify products or specifications at any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer. Analog Input Characteristics 0 dBu = 0.775 Vrms Input Jacks PAD 26 dB MIC/LINE 1 - 12 OFF ON MIC 13/14 - 19/20 - LINE 13/14, 15/16 - LINE 17/18, 19/20 - GAIN Trim Actual Load For Use With Position Impedance Nominal +64 dB +20 dB +38 dB 3 kΩ 50-600 Ω Mics/Lines -6 dB +64 dB +20 dB 3 kΩ 50-600 Ω Mic +38 dB -6 dB 10 kΩ 600 Ω Lines +38 dB -6 dB 10 kΩ 600 Ω Lines Sensitivity *1 -80 dBu (0.077 mV) -36 dBu (12.3 mV) -54 dBu (1.55 mV) -10 dBu (245 mV) -80 dBu (0.077 mV) -36 dBu (12.3 mV) -54 dBu (1.55 mV) -10 dBu (245 mV) -54 dBu (1.55 mV) -10 dBu (245 mV) Input level Nominal -60 dBu (0.775 mV) -16 dBu (122.8 mV) -34 dBu (15.46 mV) +10 dBu (2.451 V) -60 dBu (0.775 mV) -16 dBu (122.8 mV) -34 dBu (15.46 mV) +10 dBu (2.451 V) -34 dBu (15.46 mV) +10 dBu (2.451 V) Max. before clip Connector -40 dBu (7.75 mV) +4 dBu (1.228 V) -14 dBu (154.6 mV) Combo jack *2 (Balanced) +30 dBu (24.51 V) -40 dBu (7.75 mV) +4 dBu (1.228 V) XLR-3-31 *3 (Balanced) -14 dBu (154.6 mV) +30 dBu (24.51 V) Phone jack *4 (Unbalanced) -14 dBu (154.6 mV) +30 dBu (24.51 V) RCA Pin (Unbalanced) *1 Sensitivity is the lowest level that will produce an output of +4 dBu (1.228 V) or the nominal output level when the unit is set to maximum gain. (All level controls are at their maximum position.) *2 1&Sleeve = GND, 2&Tip = HOT, 3&Ring = COLD *3 1 = GND, 2 = HOT, 3 = COLD *4 Tip = Signal, Sleeve = GND Analog Output Characteristics 0 dBu = 0.775 Vrms Output Terminals Actual Source Impedance For Use With Nominal STEREO OUT [L, R] 75 Ω MONITOR OUT [L, R] GROUP OUT [1 - 4] AUX SEND [1 - 4] PHONES 150 Ω 110 Ω *3 1 = GND, 2 = HOT, 3 = COLD *5 Tip = HOT, Ring = COLD, Sleeve = GND 600 Ω Lines 10 kΩ Lines 40 Ω Phones Output level Nominal Max. before clip +4 dBu (1.228 V) +24 dBu (12.28 V) +4 dBu (1.228 V) 3 mW + 3 mW +20 dBu (7.750 V) 100 mW + 100 mW Connector XLR-3-32 *3 Phone jack *5 (Balanced) Phone jack *5 (Impedance Balanced) Stereo phone jack Digital Input / Output Characteristics (MG20XU) Terminals USB Format USB Audio Class 2.0 Data length 16-bit/24-bit Fs 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz Connector USB Standard-B