Yamaha NS-E105 Owner's Manual - Page 2

Specifications, Setting Up The Speakers

Page 2 highlights

SETTING UP THE SPEAKERS s Mounting the speakers on a wall The speakers may be mounted on a wall by using the holes provided on the speakers' back panels. Fasten wood screws into a firm wall or wall support as shown in the diagram, and hang the holes on the protruding screws. The holes on the speaker's back panels are arranged so that the speakers can be mounted in either of the two configurations shown by the following figures. Upright configuration 100 mm WARNING: * Each speaker weighs 2 kg (4 lbs. 7 oz.). Do not mount them on thin plywood or soft wall surface material, as the screws may come out of the flimsy surface, causing the speakers to fall down and be damaged, or result in personal injury. * Do not fasten the speakers to walls with nails, adhesives, or other unsound hardware. Long-term use and vibrations may cause them to fall down. * To avoid accidents resulting from tripping over loose speaker cables, fix them to the wall. Holes Diam. 4~5 mm Min. 12 mm 7 mm Tapping screw (Available at a hardware store) Wall or wall support Make sure that the screw is caught by a narrow part of the hole securely. Upright configuration Side long configuration Side long configuration 100 mm s Setting the speakers on a shelf or rack As shown in the figure, the speakers may be stood in a vertical or horizontal configuration on a shelf or a rack, by putting a supplied stand into a hole on the back of each speaker. Holes for the supplied stand Ex.) When placing the speaker upright SPECIFICATIONS Type 2 way Bass-Reflex type Speaker Unit........10 cm paper cone woofer (JA1075) 2.5 cm paper cone tweeter (JA05S4) Input Terminal Push-type Nominal Impedance 6 ohms Frequency Response ...........80 Hz - 20 kHz (-10 dB) Nominal Input Power 50W Music Input Power 200W Sensitivity 90 dB/w/m Crossover Frequency Tweeter (Low Cut 6 kHz, 6 dB/oct. Dimensions (WxHxD 210 mm x 297 mm x 100 mm (8-1/4" x 11-1/16" x 3-15/16") Weight 2 kg (4 lbs. 7 oz.) Accessories 2 speaker cables (10m each) 2 stands * Specifications subject to change without notice due to product improvements. VU 05290 Printed in Malaysia

  • 1
  • 2

The holes on the speaker’s back panels are arranged
so that the speakers can be mounted in either of the
two configurations shown by the following figures.
Upright configuration
Side long configuration
Setting the speakers on a shelf or rack
As shown in the figure, the speakers may be stood in
a vertical or horizontal configuration on a shelf or a
rack, by putting a supplied stand into a hole on the
back of each speaker.
WARNING:
* Each speaker weighs 2 kg (4 lbs. 7 oz.). Do not
mount them on thin plywood or soft wall surface
material, as the screws may come out of the flimsy
surface, causing the speakers to fall down and be
damaged, or result in personal injury.
* Do not fasten the speakers to walls with nails, adhe-
sives, or other unsound hardware. Long-term use
and vibrations may cause them to fall down.
*
To avoid accidents resulting from tripping over loose
speaker cables, fix them to the wall.
SPECIFICATIONS
Type
.......................................
2 way Bass-Reflex type
Speaker Unit
........
10 cm paper cone woofer (JA1075)
2.5 cm paper cone tweeter (JA05S4)
Input Terminal
.............................................
Push-type
Nominal Impedance
.........................................
6 ohms
Frequency Response
...........
80 Hz – 20 kHz (–10 dB)
Nominal Input Power
............................................
50W
Music Input Power
..............................................
200W
Sensitivity
...................................................
90 dB/w/m
Crossover Frequency
Tweeter (Low Cut)
..........................
6 kHz, 6 dB/oct.
Dimensions (WxHxD)
......................................
210 mm x 297 mm x 100 mm
(8-
1
/
4
” x 11-
1
/
16
” x 3-
15
/
16
”)
Weight
..............................................
2 kg (4 lbs. 7 oz.)
Accessories
...................
2 speaker cables (10m each)
2 stands
* Specifications subject to change without notice due
to product improvements.
SETTING UP THE SPEAKERS
Mounting the speakers on a wall
The speakers may be mounted on a wall by using the
holes provided on the speakers’ back panels. Fasten
wood screws into a firm wall or wall support as shown
in the diagram, and hang the holes on the protruding
screws.
Make sure that the screw is caught by a narrow part
of the hole securely.
Tapping screw
(Available at a
hardware store)
Diam. 4~5 mm
Min.
12 mm
7 mm
100 mm
Wall or
wall support
100 mm
Ex.) When placing
the speaker
upright
Holes
Upright configuration
Side long configuration
Holes
for the
sup-
plied
stand
VU 05290
Printed in Malaysia