Yamaha NX-E200 Owner's Manual - Page 3

Placing The Speakers, Removing The Front Cover, Dimensions W X H X D - speaker system

Page 3 highlights

How to connect: 1 Loosen the knob. 2 Insert the bare wire. [Remove the insulation coating at the extremity of each speaker cable by twisting the coating off.] Good No Good REMOVING THE FRONT COVER The front cover is fastened to the enclosure at four point and can be removed if desired. To remove the cover, hold on to both sides and slowly pull straight away from the speaker. To reattach, line up the four pegs on the inner surface of the cover with the four corresponding holes on the speaker and push gently. 3 Tighten the knob and secure the cable. Test the firmness of the connection by pulling lightly on the cable at the terminal. Note Do not let the bare speaker wires touch each other as this could damage the speaker or the amplifier, or both of them. PLACING THE SPEAKERS • Place the speakers on a sturdy, vibration-free surface. You may not be able to obtain good bass quality when the speakers are placed directly on the floor. Put a block, etc. under the speakers. • Better stereo images will be obtained when the speakers are slightly angled in towards the listening position. Note These speakers feature a magnetically shielded design, but there is still a chance that placing them too close to a TV set might impair picture color. Should this happen, move the speakers away from the TV set. Note When the cover is removed, be sure not to touch the speaker units with your hands or to exert excessive force with tools. SPECIFICATIONS Type 2-way bass-reflex speaker system (Magnetic shielding type) Driver 13 cm (5") cone woofer 2.5 cm (1") dome tweeter Nominal Input Power 60 W Maximum Input Power 110 W Impedance 6 Ω Frequency Response 55 Hz - 28 kHz Sensitivity 87 dB/2.83 V/m Crossover Frequency 3 kHz Dimensions (W x H x D 186 x 300 x 222 mm (7-5/16" x 11-13/16" x 8-3/4") Weight 4 kg (8 lbs. 13 oz.) x 2 Accessories Speaker cable (4 m) x 2 * Please note that all specifications are subject to change without notice. * Care should be taken not to exceed the input power values noted above. 3

  • 1
  • 2
  • 3
  • 4

3
Place the speakers on a sturdy, vibration-free surface.
You may not be able to obtain good bass quality when
the speakers are placed directly on the floor. Put a
block, etc. under the speakers.
Better stereo images will be obtained when the
speakers are slightly angled in towards the listening
position.
The front cover is fastened to the enclosure at four point
and can be removed if desired. To remove the cover, hold
on to both sides and slowly pull straight away from the
speaker.
To reattach, line up the four pegs on the inner surface of
the cover with the four corresponding holes on the
speaker and push gently.
REMOVING THE FRONT COVER
Type
.............................
2-way bass-reflex speaker system
(Magnetic shielding type)
Driver
...........................................
13 cm (5") cone woofer
2.5 cm (1") dome tweeter
Nominal Input Power
...............................................
60 W
Maximum Input Power
...........................................
110 W
Impedance
....................................................................
6
Frequency Response
................................
55 Hz – 28 kHz
Sensitivity
................................................
87 dB/2.83 V/m
Crossover Frequency
...............................................
3 kHz
Dimensions (W x H x D)
.................
186 x 300 x 222 mm
(7-5/16" x 11-13/16" x 8-3/4")
Weight
...........................................
4 kg (8 lbs. 13 oz.) x 2
Accessories
..................................
Speaker cable (4 m) x 2
*
Please note that all specifications are subject to change
without notice.
*
Care should be taken not to exceed the input power
values noted above.
SPECIFICATIONS
Note
When the cover is removed, be sure not to
touch the speaker units with your hands or to
exert excessive force with tools.
PLACING THE SPEAKERS
How to connect:
1
Loosen the knob.
2
Insert the bare wire. [Remove the insulation coating at
the extremity of each speaker cable by twisting the
coating off.]
3
Tighten the knob and secure the cable.
Test the firmness of the connection by pulling lightly
on the cable at the terminal.
Note
Do not let the bare speaker wires touch each
other as this could damage the speaker or the
amplifier, or both of them.
Good
No Good
Note
These speakers feature a magnetically shielded
design, but there is still a chance that placing
them too close to a TV set might impair picture
color. Should this happen, move the speakers
away from the TV set.