Yamaha PA2120 PA2120 Technical Specifications - Page 1
Yamaha PA2120 Manual
View all Yamaha PA2120 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
POWER AMPLIFIER VAV9690 Technical Specifications Specifications Outputs (SPEAKER OUT) Output Power 20msec Burst (THD+N=1%) AMP MODE = 3Ω AMP MODE = 4Ω AMP MODE = 8Ω AMP MODE = 70V/120W AMP MODE = 100V/120W AMP MODE = 70V/200W AMP MODE = 100V/200W Terminal Outputs (THRU OUT) THRU OUT Output Level Terminal Actual source impedance For use with nominal Nominal Inputs LINE IN Input Level (INPUT A-B, Euro, balanced) Sensitivity Nominal Max before clip Input Level (INPUT A-B, RCA, unbalanced) Sensitivity Nominal Max before clip Terminal INPUT A-B INPUT A-B General Specifications Precautions for rack mounting Operating temperature Storage temperature Dimensions (W x H x D, not including knob) Net Weight Included Accessories Optional accessories 100W x 2ch 120W x 2ch 100W x 2ch 120W x 2ch 120W x 2ch 200W x 1ch 200W x 1ch 7.62mm BARRIER STRIP 4pin 600Ω 10kΩ lines -10dBV (316mV) MONO RCA PIN x2, Unbalanced +4dBu (1.23V) +4dBu (1.23V) +24dBu (12.3V) -10dBV (316mV) -10dBV (316mV) +10dBV (3.16V) 3.5mm Euro Block 6pin x1 balanced MONO RCA PIN x2 unbalanced Rack mountable (Leave more than 1U of spaces between this unit and others.) 0°C to +40°C -20°C to +60°C 480 x 44 x 351 mm (18.90 x 1.73 x 13.82 inch) 4.8kg AC power cord (2.0m) x1, 3.5mm Euroblock plug (6pin) x1, 3.5mm Euroblock plug (3pin) x1, Owner's Manual x1, Specification sheet x1 Digital Control Panel (DCP1V4S-US/EU, DCP4V4S-US/EU, DCP4S-US/EU) Electrical Characteristics Amplifier type (Output circuitry) THD+N LINE IN to SPEAKER OUT, Half power@1kHz AMP MODE = 3Ω, 4Ω, 8Ω LINE IN to SPEAKER OUT, Half power@1kHz AMP MODE = 70V, 100V/120W LINE IN to SPEAKER OUT, Half power@1kHz AMP MODE = 70V, 100V/200W Frequency Response LINE IN to SPEAKER OUT, 50Hz to 20kHz@1W AMP MODE = 3Ω, 4Ω, 8Ω LINE IN to SPEAKER OUT, 90Hz to 20kHz@1W AMP MODE = 70V, 100V/120W LINE IN to SPEAKER OUT, 90Hz to 20kHz@1W AMP MODE = 70V, 100V/200W LINE to THRU OUT, 20Hz-20kHz Load Protection POWER/STANDBY SW on/off Output Voltage Protection DC-fault Amplifier Protection Thermal Over current Integrated Power Limit Power Supply Protection Thermal Over voltage Over current Cooling Controls Front Panel Rear Panel Connectors Indicators Analog In (MIC/LINE) Analog In (LINE) Analog Out Speakers Remote AC Power Requirement Power Consumption Standby, default setting AMP MODE = All Idle AMP MODE = 3Ω, 4Ω, 8Ω Idle AMP MODE = 70V, 100V 1/8 Output, Pink noise AMP MODE = 4Ω 1/8 Output, Pink noise AMP MODE = 70V/120W Class D ≤ 0.2% ≤ 0.2% ≤ 0.2% 0dB, -3.0dB, +1.0dB 0dB, -3.0dB, +1.0dB 0dB, -3.0dB, +1.0dB 0dB, -2.5dB, +1.0dB Mute the output Compress output voltage when needed Power Supply shutdown Limit output " Mute " Shutdown Mute the output (with automatic restoration) Compress output Power supply shutdown Power supply shutdown Limit power " Power supply shutdown Conventional cooling, bottom to up airflow POWER/STANDBY SW, OUTPUT volume x 2, BASS EQ volume x 2, TREBLE EQ volume x 2 SETUP DIP SW x1, SPEAKER A/B DIP SW x2, MODE SW x1 - 3.5mm Euro Block 6pin x1 (Rear), MONO RCA PIN x2 (Rear) MONO RCA PIN x2 (Rear/THRU OUT) 7.62mm BARRIER STRIP 4pin x1 (Rear) RJ45 x1 (Rear/DCP), 3.5mm Euro Block 3pin x1 (Rear/REMOTE) POWER x1 (Green/Orange), OUTPUT SIGNAL x2 (Green), OUTPUT LIMIT x2 (Red) 100V, 120V, 230V-240V 50Hz/60Hz (*1) *1 It has confirmed that it is working with ±10% of the voltage of the rated supply voltage. ≤ 1W 15W 20W 60W 60W Dimensions 430 480 44 361.8 45.1 (unit: mm) 379.4