Yamaha SPS-30MMS SPS-30MMS Owners Manual - Page 2
Speaker Stand
View all Yamaha SPS-30MMS manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 2 highlights
Read this before use SPEAKER STAND SPS-30MMS Thank you for selecting the Yamaha SPS-30MMS speaker stand. ASSEMBLY INSTRUCTIONS PRECAUTIONS ● This speaker stand is only for the speaker systems listed in "USABLE SPEAKERS" below. Do not use the speakers other than these listed. ● To prevent the speaker from falling, use the screws and parts provided with the stand. ● To prevent the speaker stand from falling over, select a location which is flat and stable. ● To avoid accidents resulting from tripping over loose speaker cables and to prevent the speaker stand from falling over, fix the speaker cables to the wall, etc. ● Do not let the children lean on the stand as this might cause the serious accidents resulting from the falling over of the speaker stand. ● To prevent the speaker stand from discoloring and warping, keep the speaker stand away from the stoves and places where it will be exposed to direct sunlight, etc. ● Do not attempt to clean the speaker stand with chemical solvents as this might damage the finish. Use a clean, dry cloth. ● When moving the speaker and stand, be sure to hold the support detached from the speaker. ● Secure placement or installation is the owner's responsibility. YAMAHA shall not be liable for any accident caused by improper placement or installation of speakers. ■ DIMENSIONS Top view 80 (3-3/16") 60 (2-3/8") Front view 320 (12-5/8") unit: mm(inch) ■ USABLE SPEAKERS ● NS-10MMT (NS-10MMTS) ● NX-430P (the main and rear speakers included in the NS-P430/ NS-P436 speaker package) ● NX-S20 (the front and rear speakers included in the AVX-S20 home theater sound system) ● NS-M125 ● NS-M225 ● NX-S30 (the satelite speakers included in the AVX-S30 home theater sound system) 320 (12-5/8") 6 4 (2-1/2") 278 (11") 25 (1") 618-868 (24-5/16"-34-3/16") ■ SPECIFICATIONS Dimensions (W x H x D) Weight : 320 x 618 - 868 x 320 mm (12-5/8" x 2 -5/16" - 34-3/16" x 12-5/8") : 2.4 kg (5 lbs. 4 oz.) YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A. YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA © 2005 All rights reserved. Printed in China WG59990 ● ASSEMBLY PROCEDURES Before beginning assembly, check the parts list and make sure all the parts are included. ● ASSEMBLY FIGURE For speakers with screw holes at the left and right of the speaker base. Speaker 8 Plate Pole 5 4 3 Limit of the stand height Use the binding machine screw 3 or 5 Speaker cable 8 4 3 5 2 2 7 Support ● PARTS LIST NAME QUANTITY 1 Binding tapping screw (4 x 14 mm) 6 2 Hexagon socket set screw 3 + 1 spare 3 Binding machine screw (4 x 12 mm) 2 4 Washer 2 5 Binding machine screw (6 x 14 mm) 2 6 Pad 4 7 Wrench (hexagonal) 1 8 Gasket 2 . ● ASSEMBLY PROCEDURES (You will need a screwdriver for assembly.) 1. Attaching the base and support. Pass the support through the hole from the bottom of the base, and fasten the binding tapping screws 1. • Fix the support so that the holes for the screws comes to the rear side. • Do not overtighten the binding tapping screws 1. Doing so may damage the screws or assembly. 2. Attaching the pole and support. Insert the pole to the support, and fasten the hexagon socket set screws 2 into the three holes on the support using the included wrench 7. • The line on the pole shows the limit of the stand height. Do not use the stand pulling out the pole above from this line. The hexagon socket set screw 2 of the lower side becomes ineffective and the fixation becomes unstable. Base 6 6 1 1 For speakers with screw holes at the front and rear of the speaker base. Speaker Use the binding machine screw 3 or 5 Speaker cable 8 8 4 3 Pass the speaker cable through the hole on the plate. 5 4 53 3. Attaching the pads. Put the pads 6 to the four corners on the bottom of the base to prevent the stand from moving rickety. 4. Attaching the gaskets. Put the gaskets 8 to the both sides of the plate. 5. Wiring the speaker cables. Insert the speaker cables to the hole on the plate, and pass through the pole. Aligned them to the grooved part on the bottom of the base. 6. Attaching the speakers. Line up the holes on the bottom of the speaker and the center holes on the both sides of the plate. Depending on the speakers, choose either the binding machine screws 3 (4 x 12mm) or the binding machine screws 5 (6 x 14mm) to fasten them into the holes. ■ If the speaker has 4mm holes on the bottom: Fasten the binding machine screws 3 (4 x 12mm) into the holes with a screwdriver putting the supplied washers between the screws and the plate. ■ If the speaker has 6mm holes on the bottom: Fasten the binding machine screws 5 (6x 14mm) into the holes with a screwdriver. Note • After assembly is complete, always loosen the 3 hexagon socket set screws 2 before adjusting speaker height and direction. • In order to ensure that the speakers do not fall, always hold the speakers during the assembly process.