Yamaha YDP-163 YDP-163_143 Owners Manual - Page 32

Connect the pedal cord and the AC, adaptor., Set the adjuster., YDP-163 only, Attach the headphone - review

Get Yamaha YDP-163 PDF manuals and user guides View all Yamaha YDP-163 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

Keyboard Stand Assembly 6. Connect the pedal cord and the AC adaptor. 6-1 Insert the pedal cord plug to the [TO PEDAL] jack from the rear. 6-2 Securely wind the cord holder around the pedal cord. The cord holder is attached to D. 6-3 Insert the AC adaptor plug into the DC IN jack from the rear. 6-1 6-2 7. Set the adjuster. Rotate the adjuster until it comes in firm contact with the floor surface. (YDP-163 only) 8. Attach the headphone hanger. Use the included two screws (4 x 10 mm) to attach the hanger as shown in the illustration. D 6-3 B Insert the pedal cord securely until the metal part of the cord plug disappears from view. Otherwise, the pedal may not function properly. 32 YDP-163/YDP-143 Owner's Manual NOTICE Do not hang anything other than the headphones on the hanger. Doing so may damage this instrument or the hanger. After completing the assembly, please check the following. • Are there any parts left over?  Review the assembly procedure and correct any errors. • Is this instrument clear of doors and other movable fixtures?  Move the instrument to an appropriate location. • Does this instrument make a rattling noise when you shake it?  Tighten all screws. • Does the pedal box rattle or give way when you step on the pedals?  Turn the adjuster so that it is set firmly against the floor. • Are the pedal cord plug and the adaptor plug inserted securely into the sockets?  Check the connection.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
Keyboard Stand Assembly
32
YDP-163/YDP-143 Owner’s Manual
6.
Connect the pedal cord and the AC
adaptor.
6-1
Insert the pedal cord plug to the
[TO PEDAL] jack from the rear.
6-2
Securely wind the cord holder around the
pedal cord.
The cord holder is attached to D.
6-3
Insert the AC adaptor plug into the DC IN
jack from the rear.
7.
Set the adjuster.
Rotate the adjuster until it comes in firm contact
with the floor surface.
(YDP-163 only)
8.
Attach the headphone hanger.
Use the included two screws (4 x 10 mm) to attach
the hanger as shown in the illustration.
NOTICE
Do not hang anything other than the headphones on the
hanger. Doing so may damage this instrument or the hanger.
Insert the pedal cord securely until the metal part of the
cord plug disappears from view. Otherwise, the pedal may
not function properly.
6-1
6-3
6-2
D
B
After completing the assembly, please check the
following.
•
Are there any parts left over?
Review the assembly procedure and correct any
errors.
•
Is this instrument clear of doors and other
movable fixtures?
Move the instrument to an appropriate location.
•
Does this instrument make a rattling noise when
you shake it?
Tighten all screws.
•
Does the pedal box rattle or give way when you
step on the pedals?
Turn the adjuster so that it is set firmly against the
floor.
•
Are the pedal cord plug and the adaptor plug
inserted securely into the sockets?
Check the connection.