Yamaha YHT-16 Quick Connection Guide - Page 12
Perating, Emote, Ontrol, Rogramming
View all Yamaha YHT-16 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 12 highlights
YHT-16 QUICK-C ON N ECT GUIDE PROGRAMMING THE REMOTE CONTROL (CONT'D) SETTING UP YOUR DVD (OR LD) PLAYER 1. Look up a setup code for your DVD or LD player (on page 34 of the R-V703 Owner's Manual). 2. Turn on the DVD (or LD) player. 3. On the remote control, press DVD/LD; then press and hold SETUP until the indicator LED flashes twice. 4. Using the keypad, enter the three-digit number. The indicator LED will flash twice after your entry. 5. The unit's controls are now assigned to the remote control buttons (see Quick Reference Card for use). To test the code, press DVD/LD and then POWER. If the unit does not respond, try an alternate code. SETTING UP OTHER COMPONENTS (DEVICES) 1. Look up a setup code for your component (on pages 33 through 36 of the R-V703 Owner's Manual). 2. Turn on the component. 3. On the remote control, press the appropriate component button; then press and hold SETUP until the indicator LED flashes twice. 4. Using the keypad, enter the three-digit number. The indicator LED will flash twice after your entry. 5. The unit's controls are now assigned to the remote control buttons (see Quick Reference Card for use). To test the code, press the appropriate component button and then POWER. If the unit does not respond, try an alternate code. OPERATING THE REMOTE CONTROL (RAV141) The RAV141 Remote Control will control up to seven different types of components (including the R-V703 receiver), each of which becomes active when you press a selection (e.g., TV, VCR, etc.). We can only briefly describe some functions here, and we encourage you use the Quick Reference Card and R-V703 Owner's Manual to gain additional experience with this powerful unit. PLAYING A VIDEOCASSETTE 1. Aim the remote control at the receiver, press the blue RECEIVER/TUN button, and then press POWER to turn it on. Press VCR (or 6) in the Input Select area. 2. Aim the remote control at the TV, press the blue TV button, and then press POWER to turn it on. Press TV INPUT to select the correct input. 3. Aim the remote control at the VCR, press the blue VCR button, and then press POWER to turn it on. Put a tape in the VCR, press PLAY. NOTE: At this point, the VCR controls are assigned to the remote control, since VCR was the last blue device button pressed. If you now press the VOLUME + (or -) buttons, the TV/VCR volume will be raised (or lowered). To adjust the receiver's volume, you must press the blue RECEIVER/TUN button to activate its functions. PLAYING A DVD 1. Aim the remote control at the receiver, press the blue RECEIVER/TUN button, and then press POWER to turn it on. Press DVD/LD (or 5) in the Input Select area. 2. Press the power switch on the DVD player to turn the unit on. NOTE: If the DVD player is plugged into the switched AC outlet (on the back of the receiver) and its power switch was already engaged, the unit will come on each time the receiver is powered on. 3. Load a DVD into the DVD player. 4. Aim the remote control at the DVD player, press the blue DVD button, and then press PLAY. NOTE: The DVD player's controls are now assigned to the remote control buttons, since DVD was the last blue device button pressed. 5. Press the TV/DBS or DVD/LD button to switch the R-V703 inputs from the 2-channel stereo mode to the 6-channel discrete mode. This will accept signals from the unit connected to the 6CH DISCRETE INPUT terminals. Press the button again to return the R-V703 inputs to the 2-channel mode. ©1999 YAMAHA ELECTRONICS CORPORATION, USA 6660 Orangethorpe Avenue, Buena Park, CA 90620 PH: (714) 522-9105; FAX: (800) 634-0355 http://www.yamaha.com 10