Yamaha YST-MS201 Owner's Manual - Page 6

CONTROLS & CONNECTORS (See figure 2 on page IV.) 1 INPUT Connect this 3.5 mm mini plug connector cable to the output terminal of a CD player, a personal computer, etc. which input an audio source to YST-MS201. 2 BASS control Allows you to adjust the output level of low range sound from the subwoofer. A typical (recommended) setting is the position between one o'clock and two o'clock. Rotate the control clockwise to increase the level and counterclockwise to decrease the level. 3 TO LEFT SPEAKER Connect the RCA pin plug cable from the left satellite speaker to this connector. 4 DC IN connector Connect the supplied AC adaptor to this connector. 5 TO RIGHT SPEAKER Connect the 8-pin cable from the right satellite speaker to this connector. 6 Power indicator Lights up when the power of YST-MS201 is on. 7 POWER/VOLUME control Slowly turn the control clockwise. When it clicks, the power of YST-MS201 turns on and the power indicator (6) lights up. Turn the control clockwise furthermore to increase the volume level of the entire speaker system and counterclockwise to decrease the level. To turn YST-MS201 into the standby mode, turn the control fully counterclockwise until it clicks. The power indicator (6) will also go off. SPECIFICATIONS Type Yamaha Active Servo Technology Driver Satellite 8.5 (3-3/8") ϫ 4.5 cm (1-3/4") cone, magnetically shielded type Subwoofer 12 cm (4-3/4") cone, magnetically shielded type Amplifier Output Satellite 6 W + 6 W (1 kHz, 4Ω at T.H.D.=10%) Subwoofer 18 W (100 Hz, 4Ω at T.H.D.=10%) Input sensitivity 200 mV (1 kHz, 4Ω at 6 W) Input impedance 20 kΩ Frequency response 45 Hz to 20 kHz (Satellite + Subwoofer) Power supply (AC adaptor) U.S.A. and Canada models AC 120 V, 60 Hz U.K. and Europe models AC 230 V, 50 Hz Australia model AC 240 V, 50 Hz Dimensions (W X H X D) Satellite speakers 70 (2-3/4") ϫ 195 (7-11/16") ϫ 145 (5-11/16") mm Subwoofer 193 (7-5/8") ϫ 207 (8-1/8") ϫ 214 (8-7/16") mm Weight Satellite speakers Right: 0.6 kg (1.3 lbs.) Left: 0.5 kg (1.1 lbs.) Subwoofer 2.8 kg (6.2 lbs.) Accessory AC adaptor (PA-M30) ϫ 1 * Specifications are subject to change without notice. TROUBLESHOOTING Refer to the chart below when the speakers do not function properly. If the problem you are experiencing is not listed below or if the instructions given below do not help, disconnect the AC adaptor and contact your authorized YAMAHA dealer or service center. Problem No sound comes from the speakers or subwoofer. Cause The AC adaptor is not properly plugged into the AC receptacle. The POWER/VOLUME control is set to off. The bass sound cannot be heard. Sound is distorted. Noise. Connections are faulty or incomplete. The volume setting is low. The level of the signal being inputted is too low. The BASS control is set to minimum. The level of the signal being inputted is too high. Connections are faulty or incomplete. What to Do Insert the AC adaptor firmly into the AC receptacle. Turn on the power by turning the POWER/ VOLUME control clockwise. (The power indicator lights up.) Make the connections again. Turn the POWER/VOLUME control clockwise to increase the volume. Turn up the volume on the connected component. Turn the subwoofer BASS control clockwise to increase the volume. Turn down the volume on the connected component. Make the connections again. E-2