Zanussi ZCM1031X Product Manaul - Page 9
Overall Dimensions, Instructions For The User
View all Zanussi ZCM1031X manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 9 highlights
CARE AND MAINTENANCE Before cleaning the appliance, switch off the electrical supply at the control switch. Do not clean the appliance surfaces when still hot. ENAMELLED SURFACES Clean with a damp sponge using water and mild washing-up liquid. Grease can be easily removed using hot water or a specific cleansing agent for enamelled surfaces. Do not use abrasive cleansers. ALWAYS CHECK SUITABILITY ON THE PACKAGING. Do not leave any acid or alkaline substances (lemon juice, vinegar, salt, etc.) on the enamel. AGENTS CONTAINING BLEACH MUST NOT BE USED. Clean the parts in stainless steel with specific cleansers for stainless steel surfaces. PERFORM A SPOT TEST ON AN INCONSPICUOUS ARREAR. These detergents must be applied using a soft cloth. PANSTANDS AND BURNERS To clean the burners, remove them by pulling upwards and soak them for about 10 minutes in hot water with a little detergent. After having cleaned and washed them, wipe them carefully. Make sure that gas jets are not blocked. Clean the burners once a week or more frequently if necessary. MAKE SURE YOU HAVE ASSEMBLED THE BURNERS IN A RIGHT WAY. BE CAREFUL NOT TO DAMAGE THE SPARK ELECTRODE (see fig. 14 A) . OVEN DOOR For some models, the oven door can be disassembled in the following way: open the oven door fully, hinges A are provided with two movable jumpers B; rotate the jumpers into the slot C, After that lift the door outward carring out the two movements shown in the picture. To do that, grip the sides of the door at the centre and lift the door out by lifting up slightly and pulling gently outwards. In order to reassemble the door, introduce the hinges in their relevant slots. Before closing the door, do not forget to reset the movable jumpers B. Attention, do not attempt to move the jumpers while the door is out of the oven, the hinges are under high spring tension. Fig. 9 BC A OVEN Clean the enamelled parts with a damp cloth using mild washing-up liquid and water. Grease can be easily removed using hot water or a specific cleansing agent for enamelled surfaces. Do not use abrasive cleansers. ALWAYS CHECK SUITABILITY ON THE PACKAGING AND PERFORM A 'SPOT TEST' ON AN INCONSPICUOUS AREA INSTRUCTIONS FOR THE USER OVERALL DIMENSIONS Fig. 10 87 935 11 1000 60 WARNINGS The technical data is indicated on the data plate placed on the rear of the appliance. The adjustment conditions are shown on the label stuck on the packaging and on the appliance. ' Do not use the oven door handle to move the appliance, such as removing i from the packaging. The appliance is in class 1 or class 2 subclass 1. INSTALLATION IMPORTANT: The adjacent furniture must be able to withstand a minimum temperature rise of 85deg C during periods of use. If the appliance is to b installed near units, leave the minimum gaps specified in the table below. Location Your cooker is heavy, so be careful when moving or positioning it. Do not try to move the cooker by pulling on the doors, handles or control panel. The cooker is designed to slot in between 600mm deep cabinets, spaced approximately 1000mm apart. It can also be used free-standing, with a cabinet to one side, in a corner setting or with its back to a wall. However, it must not be situated with either side closer than 20mm to a combustible wall or cupboard that is higher than the cooker. It should not be installed at the end of a run of cabinets if there is a cabinet at immediate right angles to the cooker door. In case of installation between kitchen units, their sides must withstand a temperature of at least 85 degrees C. The wall behind the cooker and 450mm above and across the width of the cooker, should be an incombustible material or easy clean surface such as ceramic tiles. Any overhanging surface or cooker hood should be at least 750mm (28) above the cooker hob. We do not recommend positioning the cooker below wall cupboards, as the heat and steam from the cooker may cause damage to the cupboard and its contents. The cooker may be located in a kitchen, or a bed-sitting room, but not not in a room be installed in containing a a bed-sitting broaothmoor fslheosws ethr.aTnh2e0mco3ok. er must LPG Models must not be installed in a room or internal space below ground level, e.g. in a basement. min. 700 mm min. 400 mm min. 50 mm min.100 mm min. 20mm min. 50 mm min. 20mm Fig. 11 9