Zanussi ZDF22002XA User Manual - Page 16

The Washing And Drying Results Are Not Satisfactory

Page 16 highlights

Problem and alarm code Possible cause and solution The appliance trips the circuit-beaker. • The amperage is insufficient to supply simultaneously all the appliances in use. Check the socket amperage and the capacity of the meter or turn off one of the appliances in use. • Internal electrical fault of the appliance. Contact an Authorised Service Centre. Refer to "Before first use", "Daily use", or "Hints and tips" for other possible causes. For alarm codes not described in the table, contact an Authorised Service Centre. Once you have checked the appliance, press . If the problem occurs again, contact an Authorised Service Centre. THE WASHING AND DRYING RESULTS ARE NOT SATISFACTORY Problem Possible cause and solution Poor washing results. Poor drying results. There are whitish streaks or bluish layers on glasses and dishes. There are stains and dry water drops on glasses and dishes. The dishes are wet. • Refer to "Daily use", "Hints and tips" and basket loading leaflet. • Use more intensive washing programmes. • Clean spray arm jets and filter. Refer to "Care and Clean- ing". • Tableware has been left for too long inside a closed appli- ance. • There is no rinse aid or the dosage of rinse aid is not enough. Set the rinse aid dispenser to a higher level. • Plastic items may need to be towel dried. • For the best drying performance activate AirDry. • We recommend to always use rinse aid, even in combination with multi-tablets. • The release quantity of rinse aid is too much. Adjust the rinse aid level to a lower level. • The quantity of detergent is too much. • The released quantity of rinse aid is not sufficient. Adjust the rinse aid level to a higher level. • The quality of the rinse aid can be the cause. • For the best drying performance activate AirDry. • The programme does not have a drying phase or has a drying phase with low temperature. • The rinse aid dispenser is empty. • The quality of the rinse aid can be the cause. • The quality of the multi-tablets can be the cause. Try a differ- ent brand or activate the rinse aid dispenser and use rinse aid and multi-tablets together. 16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20

Problem and alarm code
Possible cause and solution
The appliance trips the circuit-beaker.
The amperage is insufficient to supply simultaneous-
ly all the appliances in use. Check the socket am-
perage and the capacity of the meter or turn off one
of the appliances in use.
Internal electrical fault of the appliance. Contact an
Authorised Service Centre.
Refer to
"Before first use"
,
"Daily
use"
, or
"Hints and tips"
for other
possible causes.
Once you have checked the appliance, press
. If
the problem occurs again, contact an Authorised
Service Centre.
For alarm codes not described in the table, contact
an Authorised Service Centre.
THE WASHING AND DRYING RESULTS ARE NOT SATISFACTORY
Problem
Possible cause and solution
Poor washing results.
Refer to
"Daily use"
,
"Hints and tips"
and basket loading
leaflet.
Use more intensive washing programmes.
Clean spray arm jets and filter. Refer to
"Care and Clean-
ing"
.
Poor drying results.
Tableware has been left for too long inside a closed appli-
ance.
There is no rinse aid or the dosage of rinse aid is not enough.
Set the rinse aid dispenser to a higher level.
Plastic items may need to be towel dried.
For the best drying performance activate AirDry.
We recommend to always use rinse aid, even in combination
with multi-tablets.
There are whitish streaks or blu-
ish layers on glasses and dishes.
The release quantity of rinse aid is too much. Adjust the rinse
aid level to a lower level.
The quantity of detergent is too much.
There are stains and dry water
drops on glasses and dishes.
The released quantity of rinse aid is not sufficient. Adjust the
rinse aid level to a higher level.
The quality of the rinse aid can be the cause.
The dishes are wet.
For the best drying performance activate AirDry.
The programme does not have a drying phase or has a drying
phase with low temperature.
The rinse aid dispenser is empty.
The quality of the rinse aid can be the cause.
The quality of the multi-tablets can be the cause. Try a differ-
ent brand or activate the rinse aid dispenser and use rinse
aid and multi-tablets together.
16