Zanussi ZEV6646XBA Product Manaul - Page 10

Installation instructions

Get Zanussi ZEV6646XBA PDF manuals and user guides View all Zanussi ZEV6646XBA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

Problem You cannot activate the outer ring. The sensor fields become hot. comes on. comes on. and a number come on. Possible cause You decreased the heat setting from . Remedy Start from and only increase the heat setting. Activate the inner ring first. The cookware is too large or you put it too near to the controls. The Automatic Switch Off operates. The Child Safety Device or the Lock function operates. There is an error in the appliance. Put large cookware on the rear cooking zones if necessary. Deactivate the appliance and activate it again. Refer to the chapter "Daily use". Disconnect the appliance from the electrical supply for some time. Disconnect the fuse from the electrical system of the house. Connect it again. If comes on again, speak to the service centre. If you tried the above solutions and cannot repair the problem, speak to your dealer or the customer service. Give the data from the rating plate, three digit letter code for the glass ceramic (it is in the corner of the glass surface) and an error message that comes on. Installation instructions Make sure, you operated the appliance correctly. If not the servicing by a customer service technician or dealer will not be free of charge, also during the warranty period. The instructions about the customer service and conditions of guarantee are in the guarantee booklet. Warning! Refer to the Safety chapters. Before the installation Before the installation of the appliance, record the information below from the rating plate. The rating plate is on the bottom of the appliance casing. • Model PNC Serial number Built-in appliances • Only use the built-in appliances after you as- semble the appliance into correct built-in units and work surfaces that align to the standards. Connection cable • Use the correct mains cable of type H05BBF Tmax 90°C (or higher) for a single phase or two phase connection. • Replace the damaged mains cable with a special cable (type H05BB-F Tmax 90°C or higher). Speak to your local Service Centre. 10 www.zanussi.com

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
Problem
Possible cause
Remedy
You decreased the heat setting
from
.
Start from
and only increase the
heat setting.
You cannot activate the outer
ring.
Activate the inner ring first.
The sensor fields become hot.
The cookware is too large or you
put it too near to the controls.
Put large cookware on the rear
cooking zones if necessary.
comes on.
The Automatic Switch Off oper-
ates.
Deactivate the appliance and acti-
vate it again.
comes on.
The Child Safety Device or the
Lock function operates.
Refer to the chapter “Daily use”.
and a number come on.
There is an error in the appliance.
Disconnect the appliance from the
electrical supply for some time.
Disconnect the fuse from the elec-
trical system of the house. Connect
it again. If
comes on again,
speak to the service centre.
If you tried the above solutions and cannot re-
pair the problem, speak to your dealer or the
customer service. Give the data from the rating
plate, three digit letter code for the glass ce-
ramic (it is in the corner of the glass surface)
and an error message that comes on.
Make sure, you operated the appliance correct-
ly. If not the servicing by a customer service
technician or dealer will not be free of charge,
also during the warranty period. The instruc-
tions about the customer service and condi-
tions of guarantee are in the guarantee booklet.
Installation instructions
Warning!
Refer to the Safety chapters.
Before the installation
Before the installation of the appliance, record
the information below from the rating plate. The
rating plate is on the bottom of the appliance
casing.
•
Model
...........................
•
PNC
.............................
•
Serial number
....................
Built-in appliances
•
Only use the built-in appliances after you as-
semble the appliance into correct built-in
units and work surfaces that align to the
standards.
Connection cable
•
Use the correct mains cable of type H05BB-
F Tmax 90°C (or higher) for a single phase or
two phase connection.
•
Replace the damaged mains cable with a
special cable (type H05BB-F Tmax 90°C or
higher). Speak to your local Service Centre.
10
www.zanussi.com