Zanussi ZWH7122J Product Manaul - Page 16

Cleaning the water inlet filters, Frost precaution, Emergency emptying out

Page 16 highlights

Replace the filter into the pump by inserting it correctly into the special guides. Screw the pump cover firmly by turning it clockwise. Close the pump door. • Unscrew the hose from the machine. Keep a rag nearby because some water may flow. • Clean the filter in the valve with a stiff brush or with the piece of cloth. Caution! When the appliance is in use and depending on the programme selected there can be hot water in the pump. Never remove the pump cover during a wash cycle, always wait until the appliance has finished the cycle, and is empty. When refitting the pump cover, ensure it is securely re-tightened so as to stop leaks and young children being able to remove it. Cleaning the water inlet filters Important! If the appliance doesn't fill, takes long to fill with water, the starting button blinks yellow or the display (if available) shows the relevant alarm (see chapter "What to do if..." for more details), check if the water inlet filters are blocked . To clean the water inlet filters: • Turn off the water tap. • Unscrew the hose from the tap. • Clean the filter in the hose with a stiff brush. • Screw the hose back onto the tap. Make sure the connection is tight. 35° 45° • Screw the hose back to the machine and make sure the connection is tight. • Turn on the water tap. Frost precaution If the machine is exposed to temperatures below 0°C, certain precautions should be taken. • Turn off the water tap. • Unscrew the inlet hose. • Place the end of the emergency emptying hose and that of the inlet hose in a bowl placed on the floor and let water drain out. • Screw the water inlet hose back on and reposition the emergency emptying hose after having put the cap on again. • When you intend to start the machine up again, make sure that the room temperature is above 0°C. Emergency emptying out If the water is not discharged, proceed as follows to empty out the machine: • pull out the plug from the power socket; • close the water tap; • if necessary, wait until the water has cooled down; • open the pump door; 16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28

Replace the filter into the
pump by inserting it cor-
rectly into the special
guides. Screw the pump
cover firmly by turning it
clockwise.
Close the pump door.
Caution!
When the appliance is in use and
depending on the programme selected there can be
hot water in the pump.
Never remove the pump cover during a wash cycle, always
wait until the appliance has finished the cycle, and is
empty. When refitting the pump cover, ensure it is
securely re-tightened so as to stop leaks and young
children being able to remove it.
Cleaning the water inlet filters
Important!
If the appliance doesn't fill, takes long to fill
with water, the starting button blinks yellow or the display
(if available) shows the relevant alarm (see chapter "What
to do if..." for more details), check if the water inlet filters
are blocked .
To clean the water inlet filters:
Turn off the water tap.
Unscrew the hose from
the tap.
Clean the filter in the
hose with a stiff brush.
Screw the hose back onto the tap. Make sure the
connection is tight.
Unscrew the hose from the machine. Keep a rag
nearby because some water may flow.
Clean the filter in the valve with a stiff brush or with
the piece of cloth.
35°
45°
Screw the hose back to the machine and make sure
the connection is tight.
Turn on the water tap.
Frost precaution
If the machine is exposed to temperatures below 0°C, cer-
tain precautions should be taken.
Turn off the water tap.
Unscrew the inlet hose.
Place the end of the emergency emptying hose and that
of the inlet hose in a bowl placed on the floor and let
water drain out.
Screw the water inlet hose back on and reposition the
emergency emptying hose after having put the cap on
again.
When you intend to start the machine up again, make
sure that the room temperature is above 0°C.
Emergency emptying out
If the water is not discharged, proceed as follows to empty
out the machine:
pull out the plug from the power socket;
close the water tap;
if necessary, wait until the water has cooled down;
open the pump door;
16