ZyXEL P-100MH User Guide - Page 43

At Command Strings

Get ZyXEL P-100MH PDF manuals and user guides View all ZyXEL P-100MH manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

Prestige 100WH Internet Access Router Refer to Table 2-6 for details on how to fill in the AT commands fields. Table 2-6. Advanced WAN Setup Fields Field Description AT Command Strings: Dial Drop Answer The AT commands needed to dial. The default setting in this field is [atdt]. The AT command needed to drop a call. The default setting in this field is [+++ath]. The AT command needed to answer an incoming call. The default setting in this field is [ata]. Drop DTR When Hang Up If this field is set to [Yes], the Prestige will drop the DTR signal when hanging up a call. AT Response Strings: These strings specify the characters immediately preceding the various responses from the WAN device. CLID The string preceding the CLID (the number of calling party). The default setting in this field is NMBR. Called ID The string preceding the dialed number. The default setting in this field is TO. Speed The string preceding the DCE speed. The default setting in this field is CONNECT. When you have completed this menu, press [Enter] to return to Menu 2.1. At Command Strings For regular telephone lines, the default "Dial" string tells the modem that the line uses tone dialing. If your switch still requires pulse dialing, change the string to [atdp]. For ISDN lines, there are far more protocols and operational modes. Please consult the documentation of your TA, for you may need additional commands in both "Dial" and "Init" strings. The default AT strings should work fine for the majority of modems. Please consult the documentation of your WAN device if you need to alter them for your specific situation, especially if you have an ISDN TA. Chapter 2 Hardware Installation & Initial Setup 2-15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
Prestige 100WH Internet Access Router
2-15
Chapter 2
Hardware Installation & Initial Setup
Refer to Table 2-6 for details on how to fill in the AT commands fields.
Table 2-6.
Advanced WAN Setup Fields
Field
Description
AT Command Strings:
Dial
Drop
Answer
The AT commands needed to dial.
The default setting in this field is [atdt].
The AT command needed to drop a call.
The default setting in this field is [+++ath].
The AT command needed to answer an incoming call.
The default setting in this field is [ata].
Drop DTR When Hang Up
If this field is set to [Yes], the
Prestige
will drop the DTR signal
when hanging up a call.
AT Response Strings:
CLID
Called ID
Speed
These strings specify the characters immediately preceding the
various responses from the WAN device.
The string preceding the CLID (the number of calling party).
The default setting in this field is NMBR.
The string preceding the dialed number.
The default setting in this field is TO.
The string preceding the DCE speed.
The default setting in this field is CONNECT.
When you have completed this menu, press [Enter] to return to Menu 2.1.
At Command Strings
For regular telephone lines, the default “Dial” string tells the modem that the line uses tone
dialing. If your switch still requires pulse dialing, change the string to [atdp]. For ISDN lines,
there are far more protocols and operational modes. Please consult the documentation of your
TA, for you may need additional commands in both “Dial” and “Init” strings.
The default AT strings should work fine for the majority of modems. Please consult the
documentation of your WAN device if you need to alter them for your specific situation,
especially if you have an ISDN TA.