2012 Ford F550 Cab Diesel Supplement 3rd Printing - Page 52

2012 Ford F550 Cab Manual

Get 2012 Ford F550 Cab PDF manuals and user guides View all 2012 Ford F550 Cab manuals

Page 52 highlights

Maintenance and Specifications additive level (strength) of the coolant for maximum engine performance and protection. Three products are available for ensuring the life and health of the coolant: one tool, a test kit and a coolant inhibitor additive: • Rotunda tool ROB75240 available from your dealer - recommended refractometer to test coolant concentration. • Rotunda 328-00008 (Antifreeze Coolant ELC Contamination Kit) - Evaluates the corrosion inhibitor additive strength. Note the first step is to verify the vehicle's coolant concentration is in the correct range of 40 - 60%. Coolant concentrations outside this range will not provide valid test results. If the report results in a pass (i.e., the cooling system does not show excessive contamination/the corrosion inhibitor additive strength is sufficient), no action is required. If the report results as insufficient (does not pass), the corrosion inhibitor additive strength of the coolant is too low. If the ENGINE COOLING SYSTEM corrosion inhibitor additive strength is low, add 48 fluid oz. of Motorcraft௡ Specialty Orange Engine Coolant Revitalizer. If the SECONDARY COOLING SYSTEM corrosion inhibitor additive strength is low, add 16 fluid oz. of Motorcraft௡ Specialty Orange Engine Coolant Revitalizer. The coolant can be recharged with this additive up to two times before the coolant must be changed-out. When exchanging the full coolant volume, the system must be flushed and refilled per the instructions in the Workshop Manual. • Motorcraft௡ Specialty Orange Engine Coolant Revitalizer - Additive to boost the corrosion inhibitor level based upon the test results of the Antifreeze Coolant ELC Contamination Kit. The revitalizer may be added two times over the life of the coolant. If additional dosages are required, the cooling system must be flushed and refilled per the instructions in the Workshop Manual. Refer to Maintenance product specifications and capacities in this chapter for the proper coolant and additive specifications. Coolant change At specific mileage intervals, as listed in the scheduled maintenance information, the coolant should be changed. The optional message center, if equipped, will also display the message COOLANT CHANGE REQUIRED at this time. Refer to Maintenance product specifications and capacities in this chapter for the proper coolant. 52 2012 Diesel (67l) Supplement, 3rd Printing USA (fus)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
additive level (strength) of the coolant for maximum engine performance
and protection. Three products are available for ensuring the life and
health of the coolant: one tool, a test kit and a coolant inhibitor additive:
•
Rotunda tool ROB75240 available from your dealer – recommended
refractometer to test coolant concentration.
•
Rotunda 328-00008 (Antifreeze Coolant ELC Contamination Kit) –
Evaluates the corrosion inhibitor additive strength. Note the first step
is to verify the vehicle’s coolant concentration is in the correct range
of 40 – 60%. Coolant concentrations outside this range will not
provide valid test results. If the report results in a pass (i.e., the
cooling system does not show excessive contamination/the corrosion
inhibitor additive strength is sufficient), no action is required. If the
report results as insufficient (does not pass), the corrosion inhibitor
additive strength of the coolant is too low. If the ENGINE COOLING
SYSTEM corrosion inhibitor additive strength is low, add 48 fluid oz. of
Motorcraft
°
Specialty Orange Engine Coolant Revitalizer. If the
SECONDARY COOLING SYSTEM corrosion inhibitor additive strength
is low, add 16 fluid oz. of Motorcraft
°
Specialty Orange Engine Coolant
Revitalizer. The coolant can be recharged with this additive up to two
times before the coolant must be changed-out. When exchanging the
full coolant volume, the system must be flushed and refilled per the
instructions in the Workshop Manual.
•
Motorcraft
°
Specialty Orange Engine Coolant Revitalizer – Additive to
boost the corrosion inhibitor level based upon the test results of the
Antifreeze Coolant ELC Contamination Kit. The revitalizer may be
added two times over the life of the coolant. If additional dosages are
required, the cooling system must be flushed and refilled per the
instructions in the Workshop Manual.
Refer to
Maintenance product specifications and capacities
in this
chapter for the proper coolant and additive specifications.
Coolant change
At specific mileage intervals, as listed in the
scheduled maintenance
information,
the coolant should be changed. The optional message
center, if equipped, will also display the message
COOLANT CHANGE
REQUIRED
at this time.
Refer to
Maintenance product specifications and capacities
in this
chapter for the proper coolant.
Maintenance and Specifications
52
2012 Diesel
(67l)
Supplement, 3rd Printing
USA
(fus)