3Com 3CDSG8-US User Guide - Page 25

System Identity, Address Information, Port Information, Number of Ports, Hardware Version - default ip

Get 3Com 3CDSG8-US - OfficeConnect Managed Gigabit Switch PDF manuals and user guides
UPC - 662705533162
View all 3Com 3CDSG8-US manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

Status 25 • VLAN Information - Displays the membership information for all VLANs. Note: This page displays an overview of the switch configuration. To change the switch configuration, use the Web Management-Interface pages referenced on this page. There are two main buttons associated with this page: • HELP - Displays this window. • REFRESH - Refreshes the page with the current switch configuration and status information. 3.1.1 System Identity This section contains general information about the switch. System Name, System Location, and System Contact are set in the SYSTEM > Name page. The Software Version changes when a new version of software is updated on the switch from the SUPPORT > Update Software page. The Number of Ports, Hardware Version, and Serial Number values are created when the switch is manufactured and cannot be changed. 3.1.2 Address Information IP Address, Subnet Mask and Gateway IP Address are set from the SYSTEM > IP Address page. Management VLAN and MAC Address are fixed during manufacture and are provided here for information. 3.1.3 Port Information This table contains one row for each port on the switch. Each row is divided into eight columns as follows: • Port - The front-panel port number. • Type - All ports on this switch are 10/100/1000BASE-T. • Link Status - Up indicates that the port is connected to another device. Down indicates there is no connection. The front-panel "image" that is always visible at the top of the page, also displays this information. • Speed/Duplex Status - An indication of the speed and duplex setting of the port. This is a number, the speed in Mbps, followed by either FDX for full-duplex or HDX for halfduplex. This can be changed on the PORTS > Configuration page. • Flow Control Status - Enabled indicates that Flow Control has been enabled on the PORTS > Configuration page. • Auto-negotiation - Auto-negotiation is Enabled by default and is only Disabled when a Speed/Duplex setting other than Auto is selected on the PORTS > Configuration page. • Frame Type - Tagged means that the port will only send and receive VLAN-tagged frames. When set to All the port will also send and receive untagged packets. See VLANS > Port Config for more information. • PVID - The Port VLAN ID. When Frame Type is set to All, untagged packets arriving on the port will be associated with this VLAN. See VLANS > Port Config for more information.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
Status
25
•
VLAN Information
- Displays the membership information for all VLANs.
Note:
This page displays an overview of the switch configuration. To change the switch
configuration, use the Web Management-Interface pages referenced on this page.
There are two main buttons associated with this page:
•
HELP
- Displays this window.
•
REFRESH
- Refreshes the page with the current switch configuration and status
information.
3.1.1
System Identity
This section contains general information about the switch.
System Name, System Location
,
and
System Contact
are set in the
SYSTEM > Name
page. The
Software Version
changes
when a new version of software is updated on the switch from the
SUPPORT > Update
Software
page. The
Number of Ports, Hardware Version
, and
Serial Number
values are
created when the switch is manufactured and cannot be changed.
3.1.2
Address Information
IP Address
,
Subnet Mask
and
Gateway IP Address
are set from the
SYSTEM > IP Address
page.
Management VLAN
and
MAC Address
are fixed during manufacture and are provided
here for information.
3.1.3
Port Information
This table contains one row for each port on the switch. Each row is divided into eight columns
as follows:
•
Port
- The front-panel port number.
•
Type
- All ports on this switch are 10/100/1000BASE-T.
•
Link Status
-
Up
indicates that the port is connected to another device.
Down
indicates
there is no connection. The front-panel "image" that is always visible at the top of the
page, also displays this information.
•
Speed/Duplex Status
- An indication of the speed and duplex setting of the port. This is
a number, the speed in Mbps, followed by either
FDX
for full-duplex or
HDX
for half-
duplex. This can be changed on the
PORTS > Configuration
page.
•
Flow Control Status
-
Enabled
indicates that Flow Control has been enabled on the
PORTS > Configuration
page.
•
Auto-negotiation
- Auto-negotiation is
Enabled
by default and is only
Disabled
when
a
Speed/Duplex
setting other than
Auto
is selected on the
PORTS > Configuration
page.
•
Frame Type
-
Tagged
means that the port will only send and receive VLAN-tagged
frames. When set to
All
the port will also send and receive untagged packets. See
VLANS
> Port Config
for more information.
•
PVID
- The
Port VLAN ID
. When Frame Type is set to
All
, untagged packets arriving on
the port will be associated with this VLAN. See
VLANS > Port Config
for more
information.