ASRock 890FX Deluxe5 User Manual - Page 27

Onboard Headers and Connectors

Get ASRock 890FX Deluxe5 PDF manuals and user guides View all ASRock 890FX Deluxe5 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

2.8 Onboard Headers and Connectors Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard! FDD connector (33-pin FLOPPY1) (see p.12 No. 29) Pin1 FLOPPY1 the red-striped side to Pin1 Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the connector. Primary IDE connector (Blue) (39-pin IDE1, see p.12 No. 17) PIN1 IDE1 connect the blue end to the motherboard connect the black end to the IDE devices 80-conductor ATA 66/100/133 cable Note: Please refer to the instruction of your IDE device vendor for the details. Serial ATA3 Connectors (SATA3_1_2: see p.12, No. 20) (SATA3_3_4: see p.12, No. 19) (SATA3_5_6: see p.12, No. 18) (SATA3_7: see p.12, No. 31) (SATA3_8: see p.12, No. 32) SATA3_8 SATA3_7 Serial ATA (SATA) Data Cable (Optional) SATA3_1_2 SATA3_3_4 SATA3_5_6 These eight Serial ATA3 (SATA3) connectors support SATA data cables for internal storage devices. The current SATA3 interface allows up to 6.0 Gb/s data transfer rate. If you install the HDD on the eSATA port on the rear I/O, the internal SATA3_8 will not function. Either end of the SATA data cable can be connected to the SATA3 hard disk or the SATA3 connector on this motherboard. 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
27
27
27
27
27
2.8 Onboard Headers and Connectors
2.8 Onboard Headers and Connectors
2.8 Onboard Headers and Connectors
2.8 Onboard Headers and Connectors
2.8 Onboard Headers and Connectors
Onboard headers and connectors are NOT jumpers. Do NOT place
jumper caps over these headers and connectors. Placing jumper caps
over the headers and connectors will cause permanent damage of the
motherboard!
FDD connector
(33-pin FLOPPY1)
(see p.12
No. 29)
Note:
Make sure the red-striped side of the cable is plugged into Pin1 side of the
connector.
Primary IDE connector (Blue)
(39-pin IDE1, see p.12
No. 17)
Note:
Please refer to the instruction of your IDE device vendor for the details.
Serial ATA (SATA)
Either end of the SATA data cable
Data Cable
can be connected to the SATA3
(Optional)
hard disk or the SATA3
connector on this motherboard.
SATA3_1_2
SATA3_3_4
SATA3_5_6
Serial ATA3 Connectors
These eight Serial ATA3
(SATA3_1_2: see
p.12, No. 20)
(SATA3) connectors support
(SATA3_3_4: see
p.12, No. 19)
SATA data cables for internal
(SATA3_5_6: see
p.12, No. 18)
storage devices. The current
(SATA3_7: see
p.12, No. 31)
SATA3 interface allows up to
(SATA3_8: see
p.12, No. 32)
6.0 Gb/s data transfer rate. If
you install the HDD on the
eSATA port on the rear I/O,
the internal SATA3_8 will not
function.
FLOPPY
1
Pin
1
the red-striped side to Pin1
connect
the black end
to the IDE devices
connect the blue end
to the motherboard
IDE
1
PIN1
80-conductor ATA 66/100/133 cable
SATA3_8
SATA3_7