ASRock B75TM-ITX User Manual - Page 36

Jumpers Setup

Get ASRock B75TM-ITX PDF manuals and user guides View all ASRock B75TM-ITX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

2.9 Jumpers Setup When the jumper cap is placed on the pins, the jumper is "Short". If no jumper cap is placed on the pins, the jumper is "Open". The illustration shows a 3-pin jumper whose pin1 and pin2 are "Short" when a jumper cap is placed on these 2 pins. Clear CMOS Jumper (CLRCMOS1) (see p.13/15/17, No. 31) Default Clear CMOS CLRCMOS1 allows you to clear the data in CMOS. To clear and reset the system parameters to default setup, please turn off the computer and unplug the power cord from the power supply. After waiting for 15 seconds, use a jumper cap to short pin2 and pin3 on CLRCMOS1 for 5 seconds. However, please do not clear the CMOS right after you update the BIOS. If you need to clear the CMOS when you just finish updating the BIOS, you must boot up the system first, and then shut it down before you do the clear-CMOS action. Please be noted that the password, date, time, user default profile, 1394 GUID and MAC address will be cleared only if the CMOS battery is removed. Backlight Power Jumper (3-pin BKT_PWR1) (see p.13/15/17, No. 13) 1-2 : +12V 2-3 : +19V Panel Power Jumper (3-pin PNL_PWR1) (see p.13/15/17, No. 14) 1-2 : +3V 2-3 : +5V 36

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
36
Clear CMOS Jumper
(CLRCMOS1)
(see p.13/15/17, No. 31)
CLRCMOS1 allows you to clear the data in CMOS. To clear and reset
the system parameters to default setup, please turn off the computer and
unplug the power cord from the power supply. After waiting for 15 seconds,
use a jumper cap to short pin2 and pin3 on CLRCMOS1 for 5 seconds.
However, please do not clear the CMOS right after you update the BIOS.
If you need to clear the CMOS when you just finish updating the BIOS,
you must boot up the system first, and then shut it down before you do the
clear-CMOS action. Please be noted that the password, date, time, user
default profile, 1394 GUID and MAC address will be cleared only if the
CMOS battery is removed.
Clear CMOS
Default
2.9
Jumpers Setup
When the jumper cap is placed on the
pins, the jumper is “Short”. If no jumper
cap is placed on the pins, the jumper is
“Open”. The illustration shows a 3-pin
jumper whose pin1 and pin2 are “Short”
when a jumper cap is placed on these
2 pins.
Backlight Power Jumper
(3-pin BKT_PWR1)
(see p.13/15/17, No. 13)
1-2 : +
12V
2-3 : +19V
Panel Power Jumper
(3-pin PNL_PWR1)
(see p.13/15/17, No. 14)
1-2 : +3V
2-3 : +5V