ASRock H110TM-ITX R2.0 User Manual - Page 20

Jumpers Setup, pin PNL_PWR1

Get ASRock H110TM-ITX R2.0 PDF manuals and user guides View all ASRock H110TM-ITX R2.0 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

H110TM-ITX R2.0 2.4 Jumpers Setup The illustration shows how jumpers are setup. When the jumper cap is placed on the pins, the jumper is "Short". If no jumper cap is placed on the pins, the jumper is "Open". The illustration shows a 3-pin jumper whose pin1 and pin2 are "Short" when a jumper cap is placed on these 2 pins. Clear CMOS Jumper (CLRMOS1) (see p.6, No. 2) Default Clear CMOS CLRMOS1 allows you to clear the data in CMOS. To clear and reset the system parameters to default setup, please turn off the computer and unplug the power cord from the power supply. After waiting for 15 seconds, use a jumper cap to short pin2 and pin3 on CLRMOS1 for 5 seconds. However, please do not clear the CMOS right after you update the BIOS. If you need to clear the CMOS when you just finish updating the BIOS, you must boot up the system first, and then shut it down before you do the clear-CMOS action. Please be noted that the password, date, time, and user default profile will be cleared only if the CMOS battery is removed. Backlight Power Jumper (3-pin BKT_PWR1) (see p.6, No. 13) 1-2 : +19V 2-3 : +12V [Default] Panel Power Jumper (3-pin PNL_PWR1) (see p.6, No. 14) 1-2 : +3V 2-3 : +5V [Default] Warning: If selected Backlight Power or Panel Power is higher than panel's spec, it may damage the panel. 15 English

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
15
English
H110TM-ITX R2.0
2.4
Jumpers Setup
°e illustration shows how jumpers are setup. When the jumper cap is placed on
the pins, the jumper is “Short”. If no jumper cap is placed on the pins, the jumper
is “Open”. °e illustration shows a 3-pin jumper whose pin1 and pin2 are “Short”
when a jumper cap is placed on these 2 pins.
Clear CMOS Jumper
(CLRMOS1)
(see p.6, No. 2)
CLRMOS1 allows you to clear the data in CMOS. To clear and reset the system
parameters to default setup, please turn off the computer and unplug the power
cord from the power supply. Aſter waiting for 15 seconds, use a jumper cap to
short pin2 and pin3 on CLRMOS1 for 5 seconds. However, please do not clear the
CMOS right aſter you update the BIOS. If you need to clear the CMOS when you
just finish updating the BIOS, you must boot up the system first, and then shut it
down before you do the clear-CMOS action. Please be noted that the password,
date, time, and user default profile will be cleared only if the CMOS battery is
removed.
Backlight Power Jumper
(3-pin BKT_PWR1)
(see p.6, No. 13)
1-2 : +19V
2-3 : +12V [Default]
Panel Power Jumper
(3-pin PNL_PWR1)
(see p.6, No. 14)
1-2 : +3V
2-3 : +5V [Default]
Warning:
If selected Backlight Power or Panel Power is higher than panel's spec, it may damage the
panel.
Clear CMOS
Default