ASRock H110TM-ITX R2.0 User Manual - Page 23

Signal, 3W Audio AMP Output - manual

Get ASRock H110TM-ITX R2.0 PDF manuals and user guides View all ASRock H110TM-ITX R2.0 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

1. High Definition Audio supports Jack Sensing, but the panel wire on the chassis must support HDA to function correctly. Please follow the instructions in our manual and chassis manual to install your system. 2. If you use an AC'97 audio panel, please install it to the front panel audio header by the steps below: A. Connect Mic_IN (MIC) to MIC2_L. B. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L. C. Connect Ground (GND) to Ground (GND). D. MIC_RET and OUT_RET are for the HD audio panel only. You don't need to connect them for the AC'97 audio panel. E. To activate the front mic, go to the "FrontMic" Tab in the Realtek Control panel and adjust "Recording Volume". Analog Surround Audio Header (17-pin HD_AUDIO2) (see p.6, No. 26) Signal Signal PIN PIN Name Name 18 SENSE 17 KEY 16 LFE 15 A_GND 14 A_GND 13 Center 12 Surr_Rear_R 11 A_GND 10 A_GND 9 Surr_Rear_L 8 Surr_Side_R 7 A_GND 2 1 6 A_GND 5 Surr_Side_L 4 Front_R 3 A_GND 2 A_GND 1 Front_L 3W Audio AMP Output Wafer Header (4-pin SPEAKER1) (see p.6, No. 25) Please connect the chassis speaker to this header. SPDIF Out Connector (2-pin HDMI_SPDIF1) (see p.6, No. 24) 1 GND SPDIFOUT Please connect the SPDIF Out connector of a HDMI VGA card to this header with a cable. 1 Front_R- Front_R+ Front_L+ Front_L- English 18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
18
English
1.
High Definition Audio supports Jack Sensing, but the panel wire on the chassis must
support HDA to function correctly. Please follow the instructions in our manual and
chassis manual to install your system.
2. If you use an AC’97 audio panel, please install it to the front panel audio header by
the steps below:
A. Connect Mic_IN (MIC) to MIC2_L.
B. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L.
C. Connect Ground (GND) to Ground (GND).
D. MIC_RET and OUT_RET are for the HD audio panel only. You don’t need to
connect them for the AC’97 audio panel.
E. To activate the front mic, go to the “FrontMic” Tab in the Realtek Control panel
and adjust “Recording Volume”.
Analog Surround
Audio Header
(17-pin HD_AUDIO2)
(see p.6, No. 26)
3W Audio AMP Output
Wafer Header
(4-pin SPEAKER1)
(see p.6, No. 25)
Please connect the chassis
speaker to this header.
SPDIF Out Connector
(2-pin HDMI_SPDIF1)
(see p.6, No. 24)
Please connect the SPDIF
Out connector of a HDMI
VGA card to this header
with a cable.
SPDIFOUT
GND
1
PIN
Signal
Name
PIN
Signal
Name
18
SENSE
17
KEY
16
LFE
15
A_GND
14
A_GND
13
Center
12
Surr_Rear_R
11
A_GND
10
A_GND
9
Surr_Rear_L
8
Surr_Side_R
7
A_GND
6
A_GND
5
Surr_Side_L
4
Front_R
3
A_GND
2
A_GND
1
Front_L
Front_L+
Front_R-
Front_R+
Front_L-
1
1
2