Acer PD100 PD100 and PD120 Service Guide

Acer PD100 Manual

Get Acer PD100 PDF manuals and user guides View all Acer PD100 manuals
Add to My Manuals
Save this manual to your list of manuals

Acer PD100 manual content summary:

  • Acer PD100 | PD100 and PD120 Service Guide - Page 1
    PD100 / PD120 Service Guide Service guide files and updates are available on the AIPG/CSD web; for more information, please refer to http://csd.acer.com.tw PRINTED IN TAIWAN
  • Acer PD100 | PD100 and PD120 Service Guide - Page 2
    Revision History Please refer to the table below for the updates made on PD100 / PD120 service guide. Date Chapter Updates II
  • Acer PD100 | PD100 and PD120 Service Guide - Page 3
    software described in this manual is sold or licensed "as is". Should the programs prove defective following their purchase, the buyer (and not Acer Incorporated, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential
  • Acer PD100 | PD100 and PD120 Service Guide - Page 4
    Conventions The following conventions are used in this manual: Screen messages Denotes actual messages that appear on screen. actions. Gives precautionary measures to avoid possible hardware or software problems. Reminds you to do specific actions relevant to the accomplishment of procedures. IV
  • Acer PD100 | PD100 and PD120 Service Guide - Page 5
    available on your regional web or channel. If, for whatever reason, a part number change is made, it will not be noted in the printed Service Guide. For ACER-AUTHORIZED SERVICE PROVIDERS, your Acer office may have a DIFFERENT part number code to those given in the FRU list of this printed
  • Acer PD100 | PD100 and PD120 Service Guide - Page 6
    Procedure 8 Firmware Upgrade Troubleshooting 46 Equipment Needed 46 LED Lighting Message 46 Main Procedure 47 Function Test and Alignment Procedure 49 Product / Test Equipment / Test Condition 49 Inspection Procecdure 50 Guide to Entering Service Mode and Factory Reset (PD100
  • Acer PD100 | PD100 and PD120 Service Guide - Page 7
    with elevator mechanism +/-16 degree (32 degree) (Horizontal) Lamp power supply shut off automatically when door open Universal AC 100-240V ~ 50-60Hz with PFC input 200W for Philips UHP Lamp @ normal operation Variance FAN speed control (Depends on temperature variant) F#2.7~3.0, f=21.83mm~23.81mm
  • Acer PD100 | PD100 and PD120 Service Guide - Page 8
    Product Overview Main Unit Item 1 2 3 4 5 6 7 8 9 Focus Ring Zoom Ring Zoom Lens Elevator Button Elevator Foot Remote Control Receiver Connection Ports Power Socket Control Panel Description Chapter 1 2
  • Acer PD100 | PD100 and PD120 Service Guide - Page 9
    Control Panel Item 1 2 3 4 5 6 7 Description Lamp Indicator LED Temp Indicator LED Power / Standby and Indicator LED (Power LED) Source Resync Four Directional Select Keys Menu 3 Chapter 1
  • Acer PD100 | PD100 and PD120 Service Guide - Page 10
    Optional) PC Analog Signal / HDTV / Component Video Input Connector Audio Input Connector S-Video Input Connector Monitor Loop-through Output Connector USB Connector Remote Control IR Receiver Composite Video Input Connector KensingtonTM Lock Port 5V DC Output Jack (dfor attached dongle device) (for
  • Acer PD100 | PD100 and PD120 Service Guide - Page 11
    Connecting the Projector Item 1 2 3 4 5 6 7 8 9 5 Description Power Cord VGA Cable Composite Video Cable USB Cable VGA to Component / HDTV Adapter S-Video Cable Audio Cable Jack / Jack DVI Cable (Optional Accessory) 5V DC Output Jack for attached Dongle Device (for PD100 only) (for PD120 only)
  • Acer PD100 | PD100 and PD120 Service Guide - Page 12
    IR Front IR Data 2 4 / PC DVI RS-232 2 RS-232 WS RS-232 / VGA RS-232 A FAN 1 FAN 2 System Blower B CW Motor Photo Sensor Thermal Switch C Thermal Sensor Lamp Driver LAMP D Title Size B Date: Coretronic Corporation BLOCK DIAGRAM Document Number PD120D MB SCHEMATIC Thursday, August
  • Acer PD100 | PD100 and PD120 Service Guide - Page 13
    Firmware Upgrade Equipment Needed Software : (DDP 2000- USB) - DLP Composer - Firmware (PD100 / PD120) Hardware : Item Photo Item Projector (PD100) Projector (PD120) Chapter 2 Photo Power Cord PC or Laptop USB Cable 7 Chapter 2
  • Acer PD100 | PD100 and PD120 Service Guide - Page 14
    Composer Lite Setup Procedure No Step Procedure 1 Execute FW program Choose "DLP Composer Lite v3.6 Setup" program. 2 Next Click "Next" button. Photo 3 Next 1. Reading the "License Agreement" rules. 2. Choose "I accept and agree to be bound by all
  • Acer PD100 | PD100 and PD120 Service Guide - Page 15
    No Step 5 Next Procedure 1. Choose "All" icon 2. Click "Next" button. Photo 6 Next Click "Next" button. 7 Processing The program is executing "Initializing" status. 9 Chapter 2
  • Acer PD100 | PD100 and PD120 Service Guide - Page 16
    Procedure 1. Plug in USB Cable into the Projector. 2. Hold on "Menu" button and then plug in Power Cord. 3. Wait for about 5 seconds. (Note: The system fan will not function. The light will not function as well.) 2 Execute Program Execute the C:\Program files\DLP Composer\usbupdata.cmd. (Note: The
  • Acer PD100 | PD100 and PD120 Service Guide - Page 17
    No Step 4 Update Successfully Procedure Click "OK". The USB driver is updated successfully. Photo 5 Device Manager 1. Right click "My computer" on the desktop. 2. Select "Properties" on the popup menu to launch the "System Properties" window. 3. Choose "Hardware" and then click "Device Manager
  • Acer PD100 | PD100 and PD120 Service Guide - Page 18
    Firmware Upgrade Procedure No Step 1 Set-up 2 Procedure Link PC COM1 and projector Execute the "DLP ComposeTM" file.. 3 Click "Edit" and "Preferences". 1 Photo 2 4 1. Click "Library". 2. The library path located in the default installation directory is: C:\Program Files\DLP
  • Acer PD100 | PD100 and PD120 Service Guide - Page 19
    2. Click "Browse" to search the firmware file. (PD100 / PD120) 3. Select the item "Skip Boot Loader Area (load 1 all but the first 16KB)." 4. Click "Reset Bus" to erase the flash memory. (Note: If the error message "cannot open USB driver No projectors found" appears, please unplug the USB
  • Acer PD100 | PD100 and PD120 Service Guide - Page 20
    Picture Photo 9 1. When Firmware Upgrade Process is finished, the LED power 2. Unplug USB Cable and Power Cord. Re-plug in Power Cable after 3 mins. 10 Check Firmware Restart the unit and enter the Service Mode to check the Firmware Version. (For entering Service Mode, please refer to
  • Acer PD100 | PD100 and PD120 Service Guide - Page 21
    Needed Software: - EDID Key-in Program - EDID Program (Generic V0.51) - EDID Table (*.ini) Hardware: - V3 Fixture for EDID Key-in (Fixture: JP3 must be closed) Item Photo RS-232 Cable (F - M) Item Power Adapter for Fixture DVI Cable Generic Fixture VGA Cable PC Projector (PD100) Power
  • Acer PD100 | PD100 and PD120 Service Guide - Page 22
    Adapter to Fixture JP1 2. Fixture P1 to PC COM1 Port 3. Fixture P2 to Projector Analog Port 4. Fixture P3 to Projector Digital Port Photo Adapter To Digital Port JP1 P3 P1 P2 2. Power On Fixture Power on Fixture EDID Key-In Procedure No Step Procedure 1 Execute EDID Click on "EDID" to execute
  • Acer PD100 | PD100 and PD120 Service Guide - Page 23
    into the Barcode blank space. 2. In "White Source Select", make a check in "VGA" and "DVI". 3. Check the COM Port is "COM 1". 4. Click "Program is shown on the screen, then click "OK". Note: "RUN" message will appear on the screen. 5 Change Cable "Please change the Cable to Digital
  • Acer PD100 | PD100 and PD120 Service Guide - Page 24
    ". Note: If the code in the Serial Blank is scrambled, please make a check in "Trans". 2. Click on "Read" to read EDID information. 3. The "EDID Informations" will show the result. 4. Click "Reset" to do the next unit or "Exit" to close the EDID program. Photo 2 4 1 Note Chapter2 18
  • Acer PD100 | PD100 and PD120 Service Guide - Page 25
    This section provides disassembly & Reassembly procedures for PD100 Micro Portable SVGA DMD Projector. Before you begin any of these procedures, be sure to turn off the power, computer system, and other attached devices; then disconnect the power cable from the electrical outlet. Moreover, when
  • Acer PD100 | PD100 and PD120 Service Guide - Page 26
    Mechanical Disassembly Procedure 1. Remove Lamp Module No Procedure 1 Unscrew 2 screws to remove the Lamp Cover. Photo 2 Unscrew 2 screws to remove the Lamp Module. Chapter 3 20
  • Acer PD100 | PD100 and PD120 Service Guide - Page 27
    2. Remove IO Cover / Top Cover No Procedure 1 Unscrew 2 screws & 6 hex screws to remove the IO Cover. Photo 2 1. Lift up the Top Cover first and then pull the Bottom Cover for easily separting the Top Cover. 2. Remove 1 FPC Cable to remove the Top Cover. 21 Chapter 3
  • Acer PD100 | PD100 and PD120 Service Guide - Page 28
    3. Remove Keypad Board No Procedure 1 1. Unscrew 4 screws to remove the Keypad Board. 2. Separate the Keypad Module. Photo 2 Unscrew 2 screws to remove the Top Cover Shielding. Chapter 3 22
  • Acer PD100 | PD100 and PD120 Service Guide - Page 29
    Elevator Push Button No Procedure Photo 1 1. Unscrew 1 screw to remove the IR Receiver. 2. Unscrew 2 screws to remove the Front Cover. 2 Unplug 1 connector (red color) to remove the Front Cover Module. 3 Remove the Front IR Cover directly, and loosen 2 tenons to remove the IR Receiver Board
  • Acer PD100 | PD100 and PD120 Service Guide - Page 30
    5. Remove Bottom Cover Module No Procedure 1 Remove Bottom Cover Sponge. Photo 2 Remove Side Covers. (Right Cover & Left Cover) Note 1: When disassembing the Side Cover, push the side cover outside forwards and then pull it up directly. Note 2: When reassembing the Side Cover, please locate &
  • Acer PD100 | PD100 and PD120 Service Guide - Page 31
    be aware of the wire arrangement. The wire arrangement should go as the picture shows (not exceeding 1/2 of the red blank space) to best allocate the Top Cover Sponge. 2 1. Lift up the front part of Main Board first; then, take off the Main Board. 2. Unplug 1 connector to remove the Main Board. 25
  • Acer PD100 | PD100 and PD120 Service Guide - Page 32
    7. Remove EMI Shielding / Speaker No Procedure 1 Unscrew 4 screws to remove the EMI Shielding Cover of units. Photo 2 Unscrew 2 screws to remove the Speaker. Note: The Speaker isn't designed with error-proof. Please be aware of wire-arrangement as the picture shows. Chapter 3 26
  • Acer PD100 | PD100 and PD120 Service Guide - Page 33
    8. Remove Axial Fan Module No Procedure 1 Unscrew 3 screws to remove Axial Fan Module. Photo 2 Unscrew 4 screws to remove the System Fan. Note: The System Fan isn't designed with error-proof. Please be aware of the wirearrangement. 27 Chapter 3
  • Acer PD100 | PD100 and PD120 Service Guide - Page 34
    to remove the Lamp Driver Module. Note: When assembling the LVPS, please be aware of the LVPS connector connection. (the shorter wire should be connected to the LVPS, and the longer wire should be connected to the Lamp Driver.) 3 Unscrew 4 screws to separate the Lamp Driver Housing. Chapter 3 28
  • Acer PD100 | PD100 and PD120 Service Guide - Page 35
    10. Remove LVPS / Interlock Swtich / Thermal Switch No Procedure 1 1. Unscrew 4 screws 2. Unscrew 1 screw in the grounding wire. 3. Unplug 1 connector in the Interlock Swtich to remove the LVPS. 2 1 Photo 3 2 1. Unscrew 2 screws to remove the Interlock Switch. 2. Unscrew 1 screw to
  • Acer PD100 | PD100 and PD120 Service Guide - Page 36
    11. Remove Engine Module No Procedure 1 Unscrew 3 screws to remove the Engine Module. Photo 2 1. Unscrew 1 screw to remove the Light Cut. 2. Unscrew 1 screw to remove the Thermal Sensor. 1 2 3 Unscrew 1 screw to remove Photo Sensor Board. 4 1. Unscrew 4 screws and tear off 1 EMI tape to
  • Acer PD100 | PD100 and PD120 Service Guide - Page 37
    No Procedure When reassembling the DMD Module, please be aware of the following Notes. Note1: The DMD Heasink Spring Plate should be placed as the picture shows. Note 2: The DMD Insulator Mylar & DMD Heatsink Backer Plate should be placed as the picture shows. Note 3: The DMD Chip should be
  • Acer PD100 | PD100 and PD120 Service Guide - Page 38
    12. Remove Elevator / Blower Fan No Procedure 1 Unscrew 4 screws to remove the Elevator. Photo 2 Unscrew 3 screws to remove the Blower Fan. Chapter 3 32
  • Acer PD100 | PD100 and PD120 Service Guide - Page 39
    Mechanical Reassembly Procedure 1. Assemble Elevator / Blower Fan No Procedure 1 Screw 4 screws to assemble the Elevator. Photo 2 Screw 3 screws to assemble the Blower Fan. 33 Chapter 3
  • Acer PD100 | PD100 and PD120 Service Guide - Page 40
    2. Assemble Engine Module No Procedure 1 1. Screw 2 screws to assemble the Zoom Ring & Stopper. 2. Screw 3 screws to assemble the Focus Ring. 2 Screw 1 screw to assemble the Color Wheel. Photo Zoom Ring Zoom Ring Stopper 3 When reassembling the DMD Module, please be aware of the following
  • Acer PD100 | PD100 and PD120 Service Guide - Page 41
    No Procedure 1. Assemble the DMD Board Components. 2. Screw 4 big hex screws to assemble the DMD Board. 3. Screw 4 screws and put on 1 EMI tape to assemble the Heatsink. Photo 4 Screw 1 screw to assemble the Photo Sensor Board. 5 1. Screw 1 screw to assemble the Light Cut. 2. Screw 1
  • Acer PD100 | PD100 and PD120 Service Guide - Page 42
    3. Assemble Interlock Swtich / Thermal Switch / LVPS No Procedure 1 1. Screw 2 screws to assemble the Interlock Switch. 2. Screw 1 screw to assemble the Assy Thermal Switch Board. Photo 2 1 2 1. Screw 4 screws 2. Screw 1 screw in the grounding wire. 3. Plug 1 connector in the Interlock
  • Acer PD100 | PD100 and PD120 Service Guide - Page 43
    4 screws to assemble the Lamp Driver Housing. Photo 2 Plug in 2 connectors. Note: Please be aware of the wire arrangement of the LVPS with the Lamp Driver. (The shorter wire should be connected to the LVPS; while the longer wire should be connected to the Lamp Driver.) 3 Screw 4 screws to assemble
  • Acer PD100 | PD100 and PD120 Service Guide - Page 44
    5. Assemble Axial Fan Module No Procedure 1 Screw 4 screws to assemble the System Fan. Photo 2 Screw 3 screws to assemble Axial Fan Module. Note: Please be aware of the wire arrangement of the system fan. (the wire should be in the upper left side.) Chapter 3 38
  • Acer PD100 | PD100 and PD120 Service Guide - Page 45
    6. Assemble Speaker / EMI Shielding No Procedure 1 Screw 2 screws to assemble the Speaker. Note: Please be aware of the wire arrangement of the speaker. Photo 2 Screw 4 screws to assemble the EMI Shielding Cover of Units. 39 Chapter 3
  • Acer PD100 | PD100 and PD120 Service Guide - Page 46
    Assemble Main Board No Procedure 1 1. Plug 1 connector. 2. Locate the front part of Main Board. Photo 2 Screw 4 screws and plug in 8 connectors to assemble arrangement should go as the picture shows (not exceeding 1/2 of the red blank space) to best allocate the Top Cover Sponge. Chapter 3 40
  • Acer PD100 | PD100 and PD120 Service Guide - Page 47
    8. Assemble Bottom Cover Module No Procedure 1 Assemble the shieldings with the Main Unit based on the 2 tenons. Photo 2 Assemble Side Covers. (Right Cover & Left Cover) Note: When reassembing the Side Cover, please locate & align the tenons as the picture shows. 3 Assemble the Bottom Cover
  • Acer PD100 | PD100 and PD120 Service Guide - Page 48
    the Elevator Push Button directly. Photo 2 Assemble the IR Receiver Board and put on the Front IR Cover directly. 3 Plug in 1 connector (red color) to assemble the Front Cover Module. 4 1. Screw 1 screw to assemble the IR Receiver. 2. Screw 2 screws to assemble the Front Cover. Chapter
  • Acer PD100 | PD100 and PD120 Service Guide - Page 49
    10. Assemble Keypad Board No Procedure 1 Screw 2 screws to assemble the Top Cover Shielding. Photo 2 1. Assemble the Keypad Module. 2. Screw 4 screws to assemble the Keypad Board. 43 Chapter 3
  • Acer PD100 | PD100 and PD120 Service Guide - Page 50
    11. Assemble Top Cover / IO Cover No Procedure 1 1. Put on 1 FPC Cable to assemble the Top Cover. 2. Push the Bottom Cover first; then, push down the Top Cover to assemble the Top Cover. Photo 2 Screw 2 screws & 6 hex screws to assemble the IO Cover. Chapter 3 44
  • Acer PD100 | PD100 and PD120 Service Guide - Page 51
    12. Assemble Lamp Module No Procedure 1 Screw 2 screws to assemble the Lamp Module. Photo 2 Screw 2 screws to assemble the Lamp Cover. 45 Chapter 3
  • Acer PD100 | PD100 and PD120 Service Guide - Page 52
    Troubleshooting Equipment Needed - PC or Pattern Generator - DVD Player (Video, S-Video, Audio) - Quantum Data 802B or CHROMA 2327 LED Lighting Message Message Standby State (Input power cord) Lamp lighting Power LED Red Blue Slow Flashing O O Power on Power off (Cooling) O Quick Flashing
  • Acer PD100 | PD100 and PD120 Service Guide - Page 53
    a. Lamp LED Light - Check Lamp - Check Lamp Driver - Check Main Board b. Temp LED Light - Check Thermal Sensor - Check Thermal Switch - Check Fan c. Color Wheel - Check Color Wheel - Check Photo Sensor d. No Power - Refer to "No Power" troubleshooting - Ensure the Signal Cable and Source work as
  • Acer PD100 | PD100 and PD120 Service Guide - Page 54
    spec.) - Ensure the Projection Screen without dirt - Ensure the Projection Lens is clean - Clean DMD Chip and Engine Module - Check DMD Chip - Check Engine Module 11 Garbage Image - Ensure the Signal Cable and Source work as well - Check Main Board - Check DMD Board 12 Remote Controll or Control
  • Acer PD100 | PD100 and PD120 Service Guide - Page 55
    Function Test & Alignment Procedure Product - PD100 / PD120 Test Equipment - IBM PC with XGA 100 - Quantum Data 802B or CHROMA2316 - After changing parts, check the information below. Charge Parts/Update M/B FW Color Wheel Lamp Module Version Update v v Color Wheel ADC Index Calibration
  • Acer PD100 | PD100 and PD120 Service Guide - Page 56
    (discolor) 2. No light leakage *Please refer to page 4~7 to enter Service Mode. Use 480P signal, smtpe bar pattern to do video calibration; then, : 800x600@75Hz (PD100) - Test Pattern : Full White Pattern & Full Black Pattern - Please check and ensure the unit is under the spec. - Please check and
  • Acer PD100 | PD100 and PD120 Service Guide - Page 57
    PC Calibration - Test Signal : 800x600@75Hz (PD100) - Test Pattern : White (Top) Black (Bottom) Note: 1. Calibration Pattern should be in Full Screen Mode. 2. Please refer to 4-6. Guide to Entering Service Mode and Facotry Reset for entering Service Mode. 3. Choose and access Video Calibration & PC
  • Acer PD100 | PD100 and PD120 Service Guide - Page 58
    or amount to 6 pixel. - Test Pattern : Full White 12 Blemish (Bright) The bright - Test Pattern : Full Black / Gray 30 blemish cannot be accepted if the problem appear with Gary 30 pattern 13 Blemish (Dark) The dark blemish - Test Pattern : Full white / Blue 60 cannot be accepted if the
  • Acer PD100 | PD100 and PD120 Service Guide - Page 59
    Guide to Entering Service Mode and Factory Reset (PD100) No Item 1 Service Mode Steps Please do the following steps to enter Service Mode: 1. Turn on the projector. 2. Press "Power", "Left" button, "Left" button and "Menu" by order to enter the Service Mode. (As the following pictures show) 1
  • Acer PD100 | PD100 and PD120 Service Guide - Page 60
    Exploded Overview Chapter 5 Exploded Parts List Item Part Number Description 1 70.82V22G001 ASSY FRONT COVER MODULE PD100 2 70.82V24G001 ASSY TOP COVER MODULE PD100 3 70.82V15G001 ASSY BOTTOM HOUSING MODULE PD100 4 70.82G09G001 ASSY LAMP MODULE EP7190 5 70.82V23G001 ASSY BACK
  • Acer PD100 | PD100 and PD120 Service Guide - Page 61
    ASSY BACK COVER DC MODULE PD120 ASSY LAMP COVER MODULE PD120 SCREW PAN MECH M3*10 BLACK SCREW I/O STEEL #4-40UNC*H4*L5.5 NYLOK SCREW BIN MECH M3*6 Black GROUNDING CABLE CLAMP FN-008 "PINGOOD LOCK SCREW PAN MECH M3*8.5-3.5 BLACK Note: Please refer to RSPL for updated Part Number. 55 Chapter 5
  • Acer PD100 | PD100 and PD120 Service Guide - Page 62
    Parts List Item 1 2 3 Part Number 70.82V09G001 70.82V17G001 61.82G12G001 Description ASSY BOTTOM BASE MODULE PD120 ASSY ENGINE MODULE PD100 LAMP LIGHTCUT TOP FOR E19 AL 0.6t EP7190 4 70.82V10G001 ASSY AXIAL FAN 70.82G19G001 ASSY LAMP DRIVER MDULE EP7190 15 41.82G03G001 EMI GASKET USB CONNECTOR
  • Acer PD100 | PD100 and PD120 Service Guide - Page 63
    Parts List Item 1 2 3 Part Number 70.82V09G001 70.82V11G001 61.82G12G001 Description ASSY BOTTOM BASE MODULE PD120 ASSY ENGINE MODULE PD120 LAMP LIGHTCUT TOP FOR E19 AL 0.6t EP7190 4 70.82V10G001 ASSY AXIAL FAN 70.82G19G001 ASSY LAMP DRIVER MDULE EP7190 15 41.82G03G001 EMI GASKET USB CONNECTOR
  • Acer PD100 | PD100 and PD120 Service Guide - Page 64
    Assy Bottom Cover Module Exploded Parts List Item Part Number Description 1 51.82V02G002 BOTTOM COVER PC+ABS PD100 2 51.82V17G001 3 51.82V18G001 LEFT COVER PC+ABS PD120 RIGHT COVER PC+ABS PD120 4 52.89601.001 ADJUST FOOT RUBBER EP759 5 86.03123.035 HEX
  • Acer PD100 | PD100 and PD120 Service Guide - Page 65
    PD120 Assy Bottom Cover Module Exploded Parts List Item 1 2 3 Part Number 51.82V02G001 51.82V17G001 51.82V18G001 BOTTOM COVER PC+ABS PD120 LEFT COVER PC+ABS PD120 RIGHT HEX CAP HEAD NUT M3*0.5P L3.5 NI BOTTOM COVER SPONGE-2 PD120 Note: Please refer to RSPL for updated Part Number. 59 Chapter 5
  • Acer PD100 | PD100 and PD120 Service Guide - Page 66
    Bottom Base Module Exploded Parts List Item Part Number 1 49.88604.002 SPEAKER 8ohm 2W X16 EP759 2 85.1A123.050 SCREW PAN MECH M3*5 Ni 3 52.82G11G001 SPEAKER SPONGE EP7190 4 61.82V01G001 EMI SHIELDING AL PD120 Note: Please refer to RSPL for updated Part Number. Description Chapter
  • Acer PD100 | PD100 and PD120 Service Guide - Page 67
    85.WA123.040 9 42.82V02G001 LED HOUSING PC PD322 POWER LED HOUSING PC PD322 PCBA KEYPAD BOARD PD322 ''GREEN'' KEYPAD SHIELDING AL PD120 SCREW PAN TAP M3*4 Ni CABLE FFC 14P P=0.5 120mm PD120 10 51.82Q04G011 11 41.82V05G001 12 41.82V04G001 13 41.81M02G001 KEYPAD MENU BUTTON PC+ABS PD120 EMI
  • Acer PD100 | PD100 and PD120 Service Guide - Page 68
    .WA123.040 9 42.82V02G001 LED HOUSING PC PD322 POWER LED HOUSING PC PD322 PCBA KEYPAD BOARD PD322 ''GREEN'' KEYPAD SHIELDING AL PD120 SCREW PAN TAP M3*4 Ni CABLE FFC 14P P=0.5 120mm PD120 10 51.82Q04G011 11 41.82V05G001 12 41.82V04G001 13 41.81M02G001 KEYPAD MENU BUTTON PC+ABS PD120 EMI
  • Acer PD100 | PD100 and PD120 Service Guide - Page 69
    8 9 10 11 12 13 14 15 16 17 18 19 Part Number 61.82G01G001 51.85816.001 51.85824.001 75.88514.002 85 PD120 BUY ASSY W.A. 2P 150mm LVPS/LAMP EP719 ELEVATOR SPRING SUS304 SB21 PCBA THERMAL SENSOR BOARD PD120 BASE PLATE INSULATION MYLAR FOR LVPS EP7190 ASSY BLOWER FAN MODULE PD120 SCREW PAN MECH M4*5
  • Acer PD100 | PD100 and PD120 Service Guide - Page 70
    Axial Fan Module Exploded Parts List Item 1 2 3 4 5 Part Number 49.80N01G001 61.82V02G001 85.1F123.260 52.82V07G001 51.00075.001 Description SUNON 70*20 R-TYPE AXIAL FAN, GM1207PKVX-A 70*70*20mm, JST CONNECTOR,GREEN SUMITUDE FAN-LAMP BRACKET AL PD120 SCREW PAN MECH E/SF M3*26 Ni LAMP BRACKET
  • Acer PD100 | PD100 and PD120 Service Guide - Page 71
    Assy Engine Module Exploded Parts List Item Part Number Description 1 70.82V27G001 2 70.82V18G001 3 85.1A123.050 ASSY ENGINE BOTTOM COVER MODULE PD120 ASSY ENGINE TOP MODULE PD100 SCREW PAN MECH M3*5 Ni 4 41.82V02G001 EMI TAPE W30*L30mm PD120 Note: Please refer to RSPL for updated
  • Acer PD100 | PD100 and PD120 Service Guide - Page 72
    PD120 Assy Engine Module Exploded Parts List Item Part Number Description 1 70.82V27G001 2 70.82V12G001 3 85.1A123.050 ASSY ENGINE BOTTOM COVER MODULE PD120 ASSY ENGINE TOP MODULE PD120 SCREW PAN MECH M3*5 Ni 4
  • Acer PD100 | PD100 and PD120 Service Guide - Page 73
    PD100 Assy Engine Top Cover Module Exploded Parts List Item 1 2 3 4 Part Number 11.009F0G005-C 23.82G01G002 48.859DMGD13 51.80B31G002 5 51.82V09G001 6 51.82V10G001 7 51.82G08G001 8 51 Ni SCREW FLAT HEAD TAP M1.7x5 D3 BALCK Note: Please refer to RSPL for updated Part Number. 67 Chapter 5
  • Acer PD100 | PD100 and PD120 Service Guide - Page 74
    PD120 Assy Engine Top Cover Module Exploded Parts List Item 1 2 3 4 Part Number 11.009F0G005 23.82G01G002 48.82GDMGD01 51.80B31G002 5 51.82V09G001 6 51.82V10G001 7 51.82G08G001 8 51. Ni SCREW FLAT HEAD TAP M1.7x5 D3 BALCK Note: Please refer to RSPL for updated Part Number. Chapter 5 68
  • Acer PD100 | PD100 and PD120 Service Guide - Page 75
    Cover DC Module Exploded Parts List Item 1 2 3 4 Part Number 51.82V12G001 51.82V21G001 41.82V12G001 51.82V04G011 BACK IR LENS PC PD120 BACK IO OVERLAY-DC PC PD120 EMI TAPE W41*L129mm PD120 BACK COVER-DC PC+ABS PD120 Description Note: Please refer to RSPL for updated Part Number. 69 Chapter
  • Acer PD100 | PD100 and PD120 Service Guide - Page 76
    Cover DC Module Exploded Parts List Item 1 2 3 4 Part Number 51.82V12G001 51.82V21G001 41.82V12G001 51.82V04G012 BACK IR LENS PC PD120 BACK IO OVERLAY-DC PC PD120 EMI TAPE W41*L129mm PD120 BACK COVER-DC PC+ABS PD100 Description Note: Please refer to RSPL for updated Part Number. Chapter 5 70
  • Acer PD100 | PD100 and PD120 Service Guide - Page 77
    Exploded Parts List Item Part Number Description 1 51.82V01G002 FRONT COVER NORYL 9406P PD100 2 51.82V08G002 FRONT PUSH BUTTON PC+ABS PD100 3 SENSOR BD FOR PD120 6 35.82V01G002 MODEL NAME LABEL PC PD100 7 35.82V03G001 ACER LOGO LABEL PD120 8 52.82V11G001 FRONT COVER SPONGE PD120 9
  • Acer PD100 | PD100 and PD120 Service Guide - Page 78
    PD120 Assy Blower Fan Module Exploded Parts List Item Part Number 1 49.83A01G001 DELTA 4520 BLOW 2 52.82G08G001 BLOWER 4520 RUBBER EP7190 Note: Please refer to RSPL for updated Part Number. Description Chapter 5 72
  • Acer PD100 | PD100 and PD120 Service Guide - Page 79
    PD120 Assy Engine Bottom Cover Module 73 Chapter 5
  • Acer PD100 | PD100 and PD120 Service Guide - Page 80
    11 12 13 14 15 16 17 18 19 20 21 22 23 24 Part Number 23.82G02G001 23.82G06G001 23.82G10G001 23.82G20G001 23.82G20G011 43.80N01G001 51. 2t EP7190 ASSY COLOR WHEEL MODULE EP7190 ASSY ROD MODULE PJ406D BUY ASSY 50*25 BLOWER FAN DUCT AL EP719 SCREW DOUBLE FLAT MECH M2*3Ni SCREW PAN MECH M3*5 Ni SCREW
  • Acer PD100 | PD100 and PD120 Service Guide - Page 81
    PD120 Assy Lens Cap Module Exploded Parts List Item Part Number 1 52.82V01G001 LENS COVER RUBBER PD120 2 61.82V08G001 3 51.83150G001 LENS COVER PLATE PD120 CAP STRAP TDP-T90 Note: Please refer to RSPL for updated Part Number. Description 75 Chapter 5
  • Acer PD100 | PD100 and PD120 Service Guide - Page 82
    PD120 Assy LVPS Module Exploded Parts List Item Part Number Description 1 42.80S07G001 W.A. 14P 190mm LVPS TO M/B TDP-T90 '' 2 42.81G01.001 W.A. 2P #20 160mm LAPS/BALLAST H31 3 75.80W19G001 ASSY LVPS LITEON 200W 2300MP Note: Please refer to RSPL for updated Part Number. Chapter 5 76
  • Acer PD100 | PD100 and PD120 Service Guide - Page 83
    PD100 Assy Lamp Cover Module Exploded Parts List Item Part Number 1 51.82V13G002 LAMP COVER NORYL 9406P PD100 2 61.82V09G001 LAMP COVER PLATE SPTE PD120 3 52.82V08G001 LAMP COVER SPONGE PD120 Note: Please refer to RSPL for updated Part Number. Description 77 Chapter 5
  • Acer PD100 | PD100 and PD120 Service Guide - Page 84
    PD120 Assy Lamp Cover Module Exploded Parts List Item Part Number 1 51.82V13G001 LAMP COVER NORYL 9406P PD120 2 61.82V09G001 LAMP COVER PLATE SPTE PD120 3 52.82V08G001 LAMP COVER SPONGE PD120 Note: Please refer to RSPL for updated Part Number. Description Chapter 5 78
  • Acer PD100 | PD100 and PD120 Service Guide - Page 85
    PD120 Assy Elevator Module Exploded Parts List Item 1 2 3 4 5 Part Number 51.82V06G001 51.82V07G001 51.86809.001 61.86814.001 61.85913.001 Description ELEVATOR HOLDER PC+ABS PD120 ELEVATOR PUSH PC+ABS PD120
  • Acer PD100 | PD100 and PD120 Service Guide - Page 86
    Acer Barcode rule), 22 digits (Barcode Type: Code 128) PPPPPPPPPPWWWSSSSSMMEE The coding rule of the Bard Code: (1) PPPPPPPPPP (10 digitals) : Part from "00001". (4) MM (2 digitals) : Manufacturing Code Manufacturing Code will be applied by different manufacturing site. Coretronic : PP / RU / RM
  • Acer PD100 | PD100 and PD120 Service Guide - Page 87
    II. PCBA Code Definition PCBA Code for Projector A B XXXXXXXXXX C XXX EEEE 12 3 4 5 6 1: 2: 3: 4: 5: 6: ID Vendor Code P/N Revision Date Code S/N C: M/B B: DMD/ B 81 Appendix
  • Acer PD100 | PD100 and PD120 Service Guide - Page 88
    COVER-DC PC+ABS PD100 51.82V04G011 A BACK COVER-DC PC+ABS PD120 51.82V03G002 A TOP COVER PC+ABS PD100 51.82V03G001 A TOP COVER PC+ABS PD120 51.82V13G002 A LAMP COVER NORYL 9406P PD100 51.82V13G001 A LAMP COVER NORYL 9406P PD120 PD100 V V V V V V V V V PD120 V V V V V V V V V Appendix 82

We apologize, but we cannot currently deliver this PDF manual by request of the manufacturer.

We apologize for any inconveniece.